Search Documents

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

By José Cuadros

"El presente trabajo describe la aplicación del ""método gráfico de estabilidad"" como herramienta de diseño en el dimensionamiento de tajeos a través de técnicas geomecánicas que pueden ser aplicadas en otros yacimientos con similares condiciones que la mina Chupa a fin de mejorar la productividad y y mantener adecuadas condiciones de estabilidad de las excavaciones. En consecuencia, el dimensionamiento de los tajeos de Chupa fue uno de los varios trabajos que la Empresa Minera Iscaycruz S.A. realizó para el inicio de la explotación de este yacimiento a través del método de minado “tajeos por subniveles” con la utilización de taladros largos, sostenimiento con cables y relleno cementado. "

Sep 13, 2001

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By B. Boberg

Annual requirements of uranium to fuel the 441 currently operating nuclear reactors in the world is 170 million pounds U3O8 (65,385 tonnes U). 2005 global production was 108 million pounds (41,595 t U), of which only 2.7 million pounds U3O8 (1,039 t U), was produced from US uranium deposits. US nuclear utilities represent 26% of the global nuclear capacity but only obtain 2.5% of their supply from US uranium mines. Since 2002 annual global production increased from 93 million pounds U3O8, a 15% increase and the US production increased from 2.3 million pounds to 2.7 million pounds, a 17% increase. Reasonably Assured Resources (RAR) of 12,332 million pounds U3O8 (4.7 million t U) are reported from a wide variety of countries and types of uranium deposits. This RAR suggests that there are significant global uranium resources potentially producible at a price of $50 per pound U3O8 ($130 per kg U). Table 1 shows the distribution of global uranium resources. This table, prepared from historic data maintained by the World Nuclear Association, does not include some areas of the world that are currently considered to contain significant resources of uranium such as Mongolia. Table 1 suggests that the United States contains the fourth largest uranium resource in the world with 890 million pounds U3O8, behind Australia, Kazakhstan and Canada in resources that are producible at a price of $50 per pound U3O8 ($130 per kg U). Within the US, the states that demonstrate the greatest amount of uranium resource are Wyoming, New Mexico, Texas and the Four Corners Area of Arizona, Colorado and Utah.

Jan 1, 2007

By Sergio Neves Monteiro

This work had as its objective the characterization of a waste material, steel slag, generated from an integrated steel plant, with a view to its recycling and incorporation into red ceramics fabrication. The characterization was performed in terms of chemical composition by X-ray fluorescence (XRF), particles size distribution, X-ray diffraction (XRD), thermal analysis (DTA/TG) and scanning electron microscopy (SEM). The results indicate that the steel slag presents high amount of Ca, Fe, Mg and Si. The weight loss of the steel slag at temperatures above 800oC is associated with calcium carbonate decomposition. The coarse particle size of the steel slag is inadequate for its direct recycling into red ceramic fabrication. It is necessary to screen or to grind the waste. As a possible solution, it is suggested that screening or grinding the steel slag to a convenient particle size distribution would allow its successful industrial incorporation into red ceramics products.

Jan 1, 2006

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975

By G. Baldermann, Hüttenrauch

Occupational health and safety are an important tool to increase a company’s economic efficiency. The integration of safety-related tasks into the overall structure of entrepreneurial tasks is an inalienable requirement for the sustainable achievement of positive effects. Investments into technical and personnel occupational safety that are tied in a streamlined organizational structure guarantee the improvement of defined indicators. The labor force is of central importance. Its added value ought to be ensured. It is necessary to move away from the employees‘ hazard awareness towards a safety awareness including many other aspects in order to save costs in the long run.

Jan 1, 2005

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

By Pengfu Tan

Converter slag chemistry control has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter has been developed to predict the behavior of magnetite in the converter slag. Predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2005

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005