Search Documents

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By F. M. Doyle

Ion flotation shows great promise for recovering and removing metal ions from dilute process streams, either for environmental compliance or to recover values. This technique uses an ionic collector to concentrate non-surface active colligend ions of the opposite charge from a bulk solution at the solution?vapor interface. With a sufficiently large solution?vapor interfacial area (provided, for example, by sparging gas through the solution), the colligend can be concentrated and removed along with the collector in a foam phase. A key limitation on using the technique in the minerals industry, where many process streams contain a variety of ions and have relatively high ionic strengths, is the need to control which ions are interacting with the collector. Here the effect of three different chelating agents, namely dodecyldiethylenetriamine (Ddien), ethylene diamine tetraacetic acid (EDTA) and triethylenetetraamine (Trien), on the selectivity of copper, nickel and cobalt, or copper and alkaline earth metal ions, is reported. The results are discussed in terms of their implications for adoption in the minerals industry.

Jan 1, 2009

Sphalerites from Devonian cassiterite-sulphide deposits and Pb-Zn-Ag fissure veins have similar ranges of Cd contents, but the average Cd and Fe contents could indicate a small initial difference in availability of Cd between the Zeehan-Renison Bell district and the Mt. Bischoff-Waratah district. Sphalerites from banded Pb-Zn deposits (Rosebery and Hercules) are characterized by low Cd content which is a world-wide feature of such deposits in exIrusive rocks, and may indicaIe a genetic relationship between ore deposition and vulcanism.

Jan 1, 1968

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By D Wiseman, D Weedon, T Akroyd

Models of the size specific processes of particle collision, attachment and detachment have been combined in a form suitable for analysis of a full-scale flotation plant. The model is based on a first principal approach to particle collection by bubbles. Parameters considered include particle size, bubble size, particle contact angle, energy dissipation, entrainment and froth recovery. Using data structures configured within an Excel spreadsheet using æLimn: The Flowsheet ProcessorÆ, the model has been incorporated into a description of the individual cells within a simple roughing and cleaning flotation circuit. Simulated feeds of varying particle size distribution, feed tonnage and varying mineral hydrophobicity representing different mineral phases are presented to the model to produce predicted final concentrate grades and recoveries. Practical techniques for measuring many of the parameters included in the model are now becoming readily available. However, relating the terms included for contact angle, energy dissipation, entrainment (ie water recovery) and froth recovery to measurable parameters in operating plants remain as continuing challenges for research.

Jan 1, 2004

By Marlyn King, Kevin Peterson

Power Decks are voids created in the bottom of the borehole through the use of a suspended Super Plug. Explosive energy is started downward at initiation creating high pressures which find relief at the comers of the borehole cylinder in the bottom of the hole. This relief creates a horizontal break to the neighboring boreholes - the same effect as presplitting. This “presplit” represents a change of mass to.the explosive energy,and it is reflected upward in the more efficient form of tensile waves. This provides better use of the explosive energy than compression waves. This technique has created a new way of looking at the ways that explosive energy is transported through the rock mass.

Jan 1, 2002

By P. Roghanchi

The Rock Mass Rating (RMR) system is an internationally recognized classification system that can be used for preliminary ground control design. The RMR system assigns quantifiable values to predefined classified parameters of a rock mass. Assigning a single value rather than a range to each parameter is a source of uncertainty, however, assigning a single value can be useful for further studies related to RMR ratings. Fuzzy systems are being used in an increasing number of application areas where linguistic rules are used to describe the system. In past decades, fuzzy systems have been successfully used in geotechnical and mining engineering problems to cope with uncertain data as well as with vagueness. In such scenarios, linguistic rules and rating-based classification of rock masses have always been questionable. The objective of this study is to apply fuzzy set theory to the RMR classification system. The fuzzy system proposed in this study is specified for weak and very weak rock masses (RMR<50) based on data collected from Nevada gold mines where 68% of RMR data is in the ?poor? and ?very poor? classes. In this approach, a Mamdani fuzzy algorithm has been constructed to evaluate basic RMR89 rating for the ?wet condition.? Comparison between basic RMR89 and fuzzy RMR shows the fuzzy RMR system is valid to predict RMR from the discrete rating of each input parameter.

Feb 27, 2013

By E. L. Litchfield

The electrification of ammonium nitrate-fuel oil (AN-FO) blasting agents by pneumatic loaders is described and discussed. The consequences of the electrification are considered in light of the initiation requirements of electric blasting caps. It is recommended (1) that semiconductive loading tubing be utilized and (2) that the resistivity of the AN-FO be controlled; it is further recommended that the operator (3) test to assure continuity of the electric detonator legwire-bridgewire-legwire circuit prior to insertion of the cap into charge or borehole, (4) keep the legwires shunted but not otherwise connected to ground during loading of the blasting agent into the borehole, (5) assure that the borehole is discharged prior to hooking up the detonator leads, (6) assure that he is himself discharged prior to handling the detonator leads, and (7) assure that the blasting cap leads are never carried to the AN-FO loader. The basis and significance of these recommendations are explained.

Jan 1, 1968

Pilot-Plant Testing of Ammoniacal-Cyanidation for Gold Recovery from Copper Gold-Bearing Ore The results of pilot-plant tested ammoniacal-cyanidation of gold recovery from copper gold-bearing ore are presented in this paper. This ore is from a deposit of Russian Federation with gold and copper grade 9.5&nbsp;g/t and 0.4 per cent, respectively. Copper is largely present as malachite and azurite. The presence of chalcopyrite and bornite is also observed. In order to recover gold, gravity is recommended. Two options of ammoniacal-cyanidation using leaching of gravity tails, CIP and filtration, were tested. It was found that ammoniacal-cyanidation using filtration of leaching tailings and recycled solutions is the most optimal option. The proposed flow sheet provides for 89.7 per cent gold recovery from gravity tailings at the consumption of NaCN 0.9 kg/t and (NH4)2CO3 7.5&nbsp;-&nbsp;9 kg/t. Compared to conventional cyanidation, this technology decreases the consumption of sodium cyanide from 4 up to 0.9 kg/t at the same gold recovery. It can be recommended for the treatment of copper gold-bearing ores with the similar composition.

Sep 13, 2010

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman&apos; equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday&apos;s constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune&apos;s compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25&apos;C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:&apos; where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"&apos; system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

By Vanessa C. Koppe

During ore body modeling normally additional samples are required to improve resources evaluation and mining planning. At this stage one rises the question about where additional samples should be located. Regular sampling pattern seems to be a reasonable choice, since all the regions within the deposit receive the same number of samples without a clear clustering. Nevertheless, values for certain attributes (grades for instance) from a mineral deposits may behave more erratic in some regions than others. Consequently, by adding samples to these regions could bring more benefit for reducing the uncertainty related to a transfer function such as Net Present Value (NPV), instead of adding samples to location of low grade uncertainty. Thus, for a given number of additional data, the test of a regular pattern and a pattern which add samples on areas of high uncertainty of the attribute of interest is worth. This paper presents an algorithm that allows the construction of these two patterns, automatically, on a software commonly used in the mining industry. The algorithm leads to a fast analysis on the efficiency of the two patterns in reducing the uncertainty associated with a transfer function.

Oct 1, 2009

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system&apos;s outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle&apos; published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer&apos; in this study. The squase drainage system of a well was rep-

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.&apos;s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d&apos;Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995