Search Documents

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By T. MacKinnon, M. C. Bétournay, D. Eastick, F. C. Delabbio, C. Graves

"The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation.This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory, and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project."

Jan 1, 2005

By F F. Pitard

The optimization of metallurgical processes requires knowledge of the heterogeneity carried by constituents of interest. The common scenario, almost an industry standard, is to rely on the engineering firm who in turn relies on favorite manufacturers of sampling equipment to provide the appropriate sampling systems in the plant to perform accurate metallurgical accounting. This sequence is flawed from the beginning to the end because everything should be based on a careful understanding of the Theory of Sampling (TOS) by the company project team and their expert who invariably would suggest various approaches and different sampling systems.The necessary progressive and iterative approach should be that the company’s project team (mining or other industries) would do its home work to have a good understanding of the geometallurgy, mineralogy and texture of the ore in each geological unit so consultants and engineers would have the best information to start with. Then a reputable sampling expert would recommend which sampling systems are needed, so the company would require engineering firms to follow pre-established, non-negotiable requirements, and finally select the sampling equipment existing on the market today that is most likely to lead to accurate and precise enough metallurgical accounting.It is the author’s experience that when this necessary progressive and iterative approach is bypassed, sampling systems installed in the plant are likely to transgress the most elementary rules of sampling correctness. Invariably the argument is that the company cannot afford correct sampling systems for metallurgical accounting as suggested in the Theory of Sampling. There is nothing that is farther from the truth when later problems will develop and inevitable reconciliation difficulties with miners and geologists become daily routine with impossible answers; as a last resource the sampling expert may be called to perform a post-mortem analysis.The progressive and iterative approach suggested in this paper should be a due diligence requirement for any bank providing a loan for an important new mining project; anything less is most likely to generate unpleasant financial losses; historical, well-known examples are referred to.CITATION:Pitard, F F, 2015. A progressive, iterative approach leading to reliable metallurgical accounting sampling systems, in Proceedings MetPlant 2015, pp 78–91 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Jack Elorenta

We often hear that, "Blasting was an art, but now blasting is now a science". 'Scientific' blasting implies that we have quantified and reproducible measurements of the feedstock and product of the blasting process. However, the industry's reluctance to adopt two key technologies, drill monitoring and optical size analyzers, sheds doubt on the claims of scientific blasting.

Jan 1, 2003

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By R. F. Favreau, P. Favreau

Rock excavation is the first process in the cycle of operation of a mine, and efficient blasting is paramount to the profitability of the mine. The traditional way to design blasts has been by trial and error, based on the experience of the designer. This is probably the only important engineering practice which continues to be done without a precise engineering technique. The efficiency of most other mine processes has been improved by the use of high-tech, while a majority of blast design has not yet profited from the advantages of the computer. However, with the advent of the high-tech blast simulator Blaspa, it has become possible to design the parameters of the blast according to normal engineering practices. Over the last 50 years, the chemical and physical mechanisms which occur during a blast have come to be identified; they are reviewed in section B. Although these mechanisms are complex, they have nevertheless been expressed in terms of mathematical equations which have been assembled together in the computer to create the blast model Blaspa.

Jan 1, 2002

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By N. R. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract No. J0395028, "Noise Control of Rubber-Tired Front-End Loaders Used in Surface Mining. " Two loaders, a Caterpillar 988 and an International H-400B, were chosen for this program, and the noise sources and acoustic paths that contribute to the operator's noise exposure were identified. Retrofit noise control treatments were designed and installed on these loaders, and noise reductions of more than 10 dBA at the operator position were achieved on both machines. The retrofit packages are low cost and have been field tested in two mines for more than two years. The results of the program were communicated to the mining industry through a series of noise control workshops and a field manual. The workshops were given in nine states across the U.S. and more than 440 manuals were distributed An audio/visual slide presentation was also developed which the program.

Jan 1, 1983

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

Newmont Waihi Operations is participating in the initiation of a community liaison forum in association with the local district council. The objective is to provide a forum for the free and regular exchange of ideas, concerns and information, and through improved communication seek to achieve a more comprehensive set of solutions to community, operating and closure issues associated with Martha Mine. A similar liaison forum has been operated on two previous occasions during earlier phases of the present mine's operation. This paper deals with the practical aspects of setting up a liaison forum to act as an effective conduit between regulators, mine operators, local businesses and the community. The mechanisms and procedures for identifying community issues and concerns are dealt with. The actions and structures required to ensure effective ongoing community 'buy in' at all levels are discussed. Corporate philosophies are addressed. Specific examples from Martha Mine, Waihi New Zealand will be used to illustrate the paper. This will include a brief explanation of previous and current community issues, Newmont Waihi's operations both at Martha Mine and the proposed Favona underground mine, and the practical issues involved in setting up a liaison forum.

Jan 1, 2003

By J. Miettunen

"The lining of a grinding mill has an important role in creating the conditions for the grinding process. The main purpose of the lining is to transfer the energy taken by the mill motor to the contents of a mill. The power draw curve of the mill, if measured with sufficiently short intervals, describes how well the lining works in lifting and mixing the material to be ground.The power draw curve can also be used for determining the volumetric filling of a mill. This new measuring technique was developed at the Pyhasalmi concentrator in 1989-90. The measuring device with its PC-connections offers an excellent tool for controlling volumetric mill filling, for maximizing throughput and for research purpose (e.g. process studies, mill linings design).The paper describes the new method and the results achieved at Outokumpu's concentrators.INTRODUCTIONVarious methods have been developed for measuring mill load; weighing, noise, etc. Weighing is one of the most reliable methods but installing the sensor to existing mills is often difficult. Besides the load measurement does not indicate the volumetric filling if the specific gravity of the mill feed fluctuates. Noise measurement has often failed with its sensitivity to various disturbance sources.As known, the power draw measurement is one of the most accurate measurements in grinding circuits and therefore it has been utilized in sophisticated control, e.g. in power peak seeking algorithms for maintaining maximum grinding efficiency.About 10 years ago power oscillation measurement was developed at Pyhasalmi concentrator. In this method the amplitude of the oscillation caused by the lifters was measured. The oscillation amplitude and the mill filling has quite a good correlation and together with the power draw measurement it could be used for maximizing mill throughput (Koivistoinen and Miettunen, 1989). The main difficulties in this method were that the dependence between mill filling and the amplitude is unlinear and that the dependence also is individual for each mill.The method developed during 1989-90 is also based on the power oscillation but on its phase shift. In principle level of the material in a mill is measured. The method has been successfully used for maximizing throughput at Pyhasalmi and Enonkoski concentrators and at Harjavalta slag concentrator."

Jan 1, 1991

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah,4 and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co.5 at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By R. E. Gilchrist, R. F. Nielsen

When a gas is displaced by mother in a porous medium, and there is a relative immobile liquid present. there is a transition zone in which the gas composition varies from essentially that of the original gas to that of the injected gas. The change in extent of this zone with time may be governed by a mixing process in the direction of flow and by the rate of establishment of gas-liquid equilibrium, if the gases are appreciably soluble in the liquid. The relative importance of these two factors in deterri~ining the growth of the transition zone is discussed, with appropriate equations and experimental data. INTRODUCTION The various solution methods of oil recovery involve a transfer of the components of a mixture, whether within a single phase or between a liquid and gas. The similarity of a natural porous medium to systems used in separation and chromatographic processes makes it seem reasonable that certain concepts used by chemical engineers in "mass transfer" might be applicable to petroleum reservoirs. One approach, the HETP (height equivalent to a theoretical plate), involves a distance or length of time over which equilibrium might be con. sidered as established. Another approach involves direct use of a rate of mixing or rate of establishment of equilibrium. The latter approach has been preferred in relation to production problems. DISCUSSION AND PROCEDURE When a gas or liquid in a porous medium is displaced by one of different composition but miscible with it there will be set up a transition zone in which the composition varies from cssentially that of the original fluid to essentially that of the injected fluid. If the fluid being displaced is a gas, and there is a relatively immobile liquid present, the transition zone may be

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996