Search Documents

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Pooley F. D

The coal measures of the South Wales coalfield contain at least 50 horizons at which coal seams are known, to occur. More than 300 samples of coal were collected from these coal measures and this paper outlines thefindings of an investigation of the pattern and distribution of 12 trace elements in South Wales coals. A comparison of trace element contents of the South Wales coals is made with trace element values found elsewhereand an attempt was made to establish the organic affinity of the elements in different seams and in the coalfield 'as a whole. An important function of such an analysis is to determine the order of abundance of trace elements and this was performed for individual seams and for the whole coalfield.The interrelationship of certain elements in some seams is also examined with a view to understanding the effectiveness of such an approach to seam correlation.Ranges of values are quoted together with the mean values of the various elements. Variations of elemental values within a seam section and over the coalfield as a whole are discussed.

Jan 1, 1977

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By W L. Jennings

This paper summarises work undertaken to date as part of an investigation into the mineral resources of the proposedNorth West South Island National Park. The area covered by the proposed national park is underlain by many rock types that have undergone a long and complex history of evolution which has endowed it with some of the best potential for a wide range of different minerals in New Zealand. Many of these minerals occur only in this area or in Fiordland National Park.   The first gold-rush in the area occurred in 1856 and followed the discovery of payable gold at Lightbands Gully, south of Collingwood. The miners first focused on the alluvial deposits but soon shifted attention to lode potential. The total historical gold production for the area may be over 400 000 oz (NZ$250 - NZ$295.6 M at 1993 prices).   In addition to gold, a wide range of other minerals have been reported from the area including molybdenum, copper, nickel, zinc, silver, bismuth, stibnite, lead and antimony. The Onekaka iron-ore deposits have produced small tonnages of ochre and iron-ore at various times. Tungsten, platinoids and other metals have been. given only minor attention. The diverse geology of the Northwest Nelson has resulted in the occurrence of many industrial minerals which have been exploited in generally small-scale operations. Aggregate, chrysotile asbestos, clay, dolomite, marble, limestone, dimension stone, rip-rap, talc-magnesite and wollastonite have all been produced.

Jan 1, 1993

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By S Rupprech, T Lund, H Fourie, PH van Rooyen, NM Vegter

Rosh Pinah Zinc Corporation (Pty) Ltd (RPZC) operates an underground mine at Rosh Pinah in southern Namibia producing zinc and lead sulphide concentrates. It currently mines around 0.7 Mtpa run-of-mine ore containing around 6-10% zinc and 1.5-3.5% lead. As part of past exploration and current intensified exploration, a massive continuous low grade ore body was identified which grades at around 3% zinc equivalent. This ore body is near current mining infrastructure and could be amenable to bulk mining methods. In the present paper a concept is presented on how it could be exploited. As a precursor to exploitation of the low grade a number of enhancements are proposed for the current mining operations including: ? shortening load-and-haul distances by extending the conveyor raise further down the mine in a phased manner and back-filling of waste into mined-out stopes; ? use of mobile crushing plant at the crusher tip, and; ? installation of a system to allow scoops to load directly from stopes into ore passes close by combined with truck loops to haul from these ore passes to the crusher tip. To exploit the low grade ore body the following concepts are proposed: ? open stope mining from two areas at a total rate of up to 2 Mtpa; ? underground pre-beneficiation of mined low-grade ore near the stopes using either dense medium separation or X-ray sorting; ? pre-beneficiated tails back-filled to mined-out stopes and; ? pre-beneficiated product transported to surface by linking into proposed run-of-mine conveying system.

Jan 1, 2007

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By Malcolm Ross

Fibrous minerals are common in nature but asbestiform minerals are rare. The unique mineralogical characteristic common to all the asbestos minerals is their morphologic form (or habit of crystallization) as polyfilamentous fiber bundles. The individual fibrils within the bundles have a tendency to be very long with a narrow range of diameters and grow with their long fiber axis in parallel orientation to the bundle length. The asbestiform habit imparts to the asbestos minerals sufficient flexibility and tensile strength so that most can be woven into cloth. In the past application has focused on their ability to insulate against the transfer of heat. However, these minerals possess other properties which make them useful in many industrial applications. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Asbestiform; Fibrous

Jan 1, 2007

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978