Search Documents

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By Paul Worsey, Dave McCool, Ryan Freeman, Chris Wolters, Rick Hines, John Bowles

Carroll Cave, located in Camden County, in south central Missouri, is one of the most significant caves in Missouri with over 12 miles of mapped passages and over 100 known but unmapped side passages. In the early 1990’s there was a breakdown of the originally excellent landowner/caver relations as the ownership of the only known entrance moved to a new generation and grottos squabbled for control. Subsequently the current owner of the natural cave entrance refused to grant anyone permission to enter.

Jan 1, 2003

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By Michael Valencia, Alonso Marchena, Fredy Arcos, Miguel Chumbe

Cobrepampa es un depósito de cobre ubicado en Acarí (Caravelí-Arequipa). La mineralización se emplaza en pórfidos dioríticos pertenecientes al intrusivo Cobrepampa (Superunidad Linga) y está constituida por bornita, calcosina, covelina y calcopirita y en la zona de oxidación cuprita, crisocola, malaquita y hematita. El magmatismo es calcoalcalino con alto K. El intrusivo Cobrepampa evoluciona por fraccionamiento y contaminación en una corteza más delgada que la superunidad Linga. Petromineralógicamente se tiene epidotización con diseminaciones de calcopirita, pirita y bornita, gangas de cuarzo y calcita con hematita acicular. Las inclusiones fluidas muestran temperaturas de homogenización de 165.5 - 266.43 °C y salinidad 3.5 - 16.8 % eq. peso NaCl de un mesotermal o epitermal, pero que por sus características geomineralógicas sería un mesotermal. Por tanto, Cobrepampa presenta más de un evento de mineralización: una con magnetita y actinolita, y otro mesotermal de vetas de cuarzo con sulfuros.

May 22, 2019

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By R. N. Zitter

PRESENT work was done in connection with a program for obtaining a low energy gap semiconductor suitable for photodetection. The inter-metallic compound InSb, which is now being in-

Jan 1, 1959

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick's Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for <20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick's Stream.

Jan 1, 2003

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009