Search Documents

By Akira Tsune, Shingo Sugimoto, Tadayuki Ishiyama, Nadao Saito, Masatsugu Okazaki

"The Deep Ocean Resources Development Co. Ltd. (DORD) of Japan signed a 15-years contract with the International Seabed Authority for exploration of polymetallic nodule in a 75,000 km2 area, consisting of West and East Areas in the Clarion and Clipperton Fracture Zone in 2001. The exploration work is now concentrated in resource estimation of the first generation of mining area, the High Abundance Area.A detail survey of the Model Area, set in the High Abundance Area, was conducted using AUV (Autonomous Underwater Vehicle) equipped with MBES (Multi-Beam Echo Sounder), SSS (Side Scan Sonar), Sub-Bottom Profiler (SBP) and still camera. The seafloor topographic map based on 1 m grid data was produced in an area of approximately 80 km2 (Figure 1). Photographs, continuously covering the seafloor taken by AUV along two west-east trending traverse lines, together with detail seafloor topographic map produced from MBES give an excellent opportunity to observe distribution manner of pollymetalic nodule related to topographic features. This helps to understand more accurate resources estimation of a whole area of the High abundance Area. Furthermore, information of micro-topography gives ideas for conducting ore collecting operation and designing ore collector."

Sep 1, 2014

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By Michael Wieland

The resolving capacity of the thermodynamic work-principal model has been seriously refined over its twelve year history, so a review of the innovations, wrong turns and their rectification is warranted to help future researchers. The work-principal model rests upon the four laws of thermodynamics that drive the universe and relatively few other assumptions: like the removing and imposing of constraints on the quasi-potential to yield trapped minimum key-states that represent the wanted process. The formative research was concerned with the role of ingredient changes, the removal of booster influence and the quench temperature with which to reckon toxic fumes. The transfer of reaction-zone energy as work upon the surrounding rock/water/fixture was not fully rationalized until the notion of reversed-inertial pressure was formulated and determined (for water) with underwater trinitrotoluene (TNT) shots. The rock-water-jelly model incorporated that term into its dynamic pressure formula as a way to represent rock blasts or underwater shots, while the zone of reaction gases remained trapped. The real irreversible thermodynamic process, which yielded the total expansion work, was later complemented with a wholly reversible imaginary process, to form a closed thermodynamic loop, with a remarkable consequence – the determination of the theoretical heave and hence, the undissipated-shock by difference from the total work. With the wholly developed model, it was recently possible to quantify the time retardation of reaction chemistry for non-molecular (mining) explosives, as compared to the rather negligible time-retardation found for the molecular (military) explosives in underwater tests.

Jan 1, 2009

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

By Alex Del Castillo

The mineral processing industry has followed the development of database control systems, and various systems have been installed in existing and new plants. The goal is to improve product quality, raise productivity and lower production costs. Improvements in different units for mineral .processing .have been applied. This has led to increasing information for the operators. To support the operators and for an easy overview of the process, a complete concept for an integrated process-control system is required. This paper describes the plant-wide [process control system for the Collahuasi copper project located in northern Chile. The total investment for the project was $1,700,000,000 and included a port area and two copper processing plants, an oxide plant with a cathode production of 50 tons per year and a sulfide plant with a concentrate production of 330 kilotons per year. The main characteristics of the plant-wide process control system include a 200- kilometer long redundant control network and a 24-kilometer long redundant serial network providing coverage for the entire plant. The plants are located around 4,700 meters above sea level, serial communication lids allow the integration of over 2,700 SCADA data units, and the system handles over 7,500 physical signals plus the SCADA data integration. The main equipment consists of 39 different sized controllers, 16 operator stations, 5 engineering stations, 2 information management systems and 4 X- terminals. The project management, control configuration, factory acceptance test, system integration test, training, commissioning and start-up were carried out in close cooperation with the customer. The result was completely satisfactory for the customer.

Jan 1, 1999

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

By E. A. Adey, C. Baciu, P. Whitbread-Abrutat, M. Varul, T. Ejdemo, R. K. Shail, F. Wall

Responsible mining requires stakeholder engagement throughout all operational stages and after mine closure. By assessing the current and anticipated future socio-economic and environmental impacts, a company can maximise the positive impacts they can have on a community, whilst minimising any negative impacts. Despite the current emphasis on companies maintaining effective stakeholder relations to gain their ‘social license’ to operate, findings of the present study reveal a wide variation in community expectations, with different degrees of ‘acceptability’ evident across seven sites in Romania (Rosia Montana), Sweden (Kristineberg), the United Kingdom (Cornwall), Bosnia Herzegovina (Vihovici) and Russia (Karabash, Gay and Mednogorsk). These variations reflect the current status of mining within a community, as well as its socio-economic background and the nature of existing engagement with mining companies already operating in the region.

Jan 1, 2011

The green field site is one that has no history of mining and as such it presents the designer with a blank canvas, on which any number of drill and blasting options can be drafted. No matter which mining method is selected all technology and experience will need to be acquired from outside sources, applied quickly and produce the right results. North Limited, in joint venture with the Sumitomo Group (20 per cent), have developed AustraliaÆs first block cave mine at Northparkes in New South Wales, Australia. This innovative and large scale mining project was taken from a green field site in November 1993 to a fully commissioned block cave mine in December 1997. NorthparkesÆ Endeavour 26 mine is now producing at a rate of 3.9Mt per annum from a 27Mt ore block. Prior to 1993 no history of mining activity existed at Northparkes. The rock had never been blasted and many questions were raised about how it would behave. While it was clear that the Endeavour 26 (E26) orebody contained geotechnical properties appropriate to block caving, the blasting methods required to establish a block cave mine had never been used in Australia and no designs were available. The joint venture partners had no prior experience with block caving and it was immediately apparent that this blasting technology would have to be acquired from foreign sources and applied to the unique local conditions. Conceptual designs for the block cave drill and blast were first drafted in 1994, first issued for drilling in December 1995 and first blasted in January 1996. 470 km of drill metres and four million tonnes of rock were blasted to complete the undercutting project by September 1997. This paper will provide those developing new drill and blast projects with an inside view of how one small technical team solved many design challenges to successfully construct AustraliaÆs first block cave mine under strict quality controls and ambitious time constraints.

Jan 1, 1998

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

The paper presents a brief history of endeavours to start a mining education programme which began in the days when Papua New Guinea's first large mine, at Panguna (Bougainville), was coming into production. The status of the Public Investment Programme in Mining Engineering and the facilities being created for the education and training of Papua New Guinean citizens in mining and mineral processing are also described. Future expansion plans are also detailed including those for the commencement of petroleum engineering and geological engineering which would include courses in mining geology, exploration geology, engineering geology and petroleum geology. The paper also looks at the manpower training requirements in the lower levels of mining industry such as pit foreman, blasting foreman and other similar positions. It stresses the need to start mining technical training programs at pre- employment level and at certificate level in a technical college, possibly Lae Technical Colleqe.

Jan 1, 1991

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.