Search Documents

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

By I. C. L. Webster, G. E. Ray

"The magnetite-rich Heff Cu-Au skarn lies in the Quesnel Terrane of south-central British Columbia, approximately 26 km northeast of Kamloops. The skarn formed close to the northern margin of the Heffley Creek pluton, and is hosted by Carnian (Late Triassic) Nicola Group limestone. The Late Triassic pluton (208.1 ± 6.1 Ma, U-Pb zircon) is a composite body of alkaline affinity that includes dioritic, gabbroic, and magnetite-rich clinopyroxene ± olivine ultramafic phases.The skarn has been discontinuously traced along strike for more than 1 km, and individual skarn layers are up to 40 m thick. The most common non-opaque minerals are garnet, clinopyroxene, and carbonate, with lesser epidote, biotite, amphibole, and chlorite. Apatite locally forms more than 3 vol.% of the rock. Compositionally the garnet is a low Mn grandite averaging Pyr3-Grs41-Adr56 mol.%.Mineralization consists of lenses, up to 10 m thick, containing massive low Ti-V magnetite (avg. 0.03 wt.% TiO2 and 0.01 wt.% V2O3). Magnetite is associated with up to 20 vol.% pyrrhotite, lesser pyrite, and trace chalcopyrite and gold. There is a moderate enrichment in rare earth elements with assays up to 570 ppm La and 490 ppm Ce. The Heffley Creek pluton belongs to a suite of Late Triassic-Early Jurassic alkalic and Fe-rich intrusions that are widely developed throughout the Quesnel Terrane. Some host Cu-Au porphyry mineralization, but less commonly they are associated with magnetite-apatite veins such as at the Glen Iron mine and Magnet occurrence, or with magnetite-rich Cu-Au skarns such as the Heff occurrence.Although abundant low Ti magnetite is present in the Heff skarn, it does not appear to represent iron oxide copper- gold (IOCG) type mineralization. Microprobe analyses completed during this study show that low Ti magnetite is not a unique feature of IOCG deposits, but also characterizes some other types of hydrothermal mineralization. In British Columbia these include some alkalic porphyry-related magnetite-apatite veins in the Quesnel Terrane, as well as the well-known Wrangellia-hosted Fe skarn deposits. Thus, low Ti magnetite appears to be a common signature of many magmatic hydrothermal deposits in contrast to the high Ti primary magnetite found in most igneous rocks."

Jan 1, 2007

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

So many emergencies that crop up in mining necessitate a departure from ordinary methods that the writer has been led to illustrate a few of the examples that have come under his notice during a somewhat lengthy career; and as most of the methods illustrated are certainly outside the ordinary, it may be hoped that while to many they may convey little that is new, to the larger number some acceptable information may be gleaned whenever the occasion calls for it. Experience has shown that there can be no hard and fast rule in mine timbering that will fit the varying- necessities of different localities, and the engineer must divest his mind of all prejudices that his practice of any particular system or systems may have induced, and must direct his attention to the character of the local timber and its fitness or otherwise for the purpose he has in view. Fortunate indeed are the man and mine that can claim an abundance of good and cheap mining timber it simplifies, oftentimes, what would be, under unfavourable timber conditions, a difficult problem. In many parts of the States there is either none or at best a scrub if the latter, he has to either pigstye, balk, or bulkhead, if his ground will permit; if, not, and the necessary timber has to be imported, then some system of recovering his timber and using it over and over again may be possible. As an illustration of this, Fig-s. Nos. I and 2 show a method applied to the copper deposits of the LyellTharsis, Tasmania. The workings were wide; varying from 30 ft. to 50 ft., and the deposit a taIcose schist of fairly good...

Jan 1, 1902

By Joe Holmes, Peter Langlois

"Falconbridge’s Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region, has been in operation since December 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,000,000 tonnes per year. Optimization of the ABC grinding circuit has proven to be the most challenging component of this capacity increase. Concurrent flotation circuit modifications have allowed concentrate grades to increase from 16 to 18 percent nickel, while maintaining recoveries. Concentrate drying problems encountered during the first 15 months of operation have been addressed through equipment upgrades. The challenges associated with surface deposition of filtered tailings in an arctic environment are now better understood, and detailed design of the progressive reclamation cover is underway.GRINDINGCircuit OverviewOre from open pit and underground mining operations is introduced to the underground ore handling system via surface and underground truck dumps. Two underground bins with a combined capacity of 4000 tonnes provide roughly a day of live capacity for ore storage. Ore from the two bins is conveyed to a 150 tonne surge bin immediately ahead of the grinding circuit in the concentrator.The Raglan grinding circuit has a conventional ABC configuration (Figure 1) with a design capacity of 100 mtph (800,000 tonnes per year). The 24’ AG mill is powered by a 3000 hp motor with variable speed drive. AG discharge is sized on a 8’x16’ single deck vibrating screen, with screen oversize recirculating to a 5 %’ short head cone crusher (400 hp) before returning to the AG mill. Screen undersize is combined with ball mill discharge to feed up to 5 15” Krebs hydrocyclones. The ball mill is a 14’x 21’ overflow mill driven by a 3000 hp motor at 73% critical speed. Target Pgo for the grinding circuit product is 65 microns"

Jan 1, 2001

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

Determination of Flotation Kinetics of Coal Grain Types in a Pilot Scale Jameson Cell using Coal Grain Analysis Method

Sep 13, 2010

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979