Search Documents

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Jouko L. Lehtonen

Sheet pile walls can be sealed watertightly using various methods. The objective of this paper is to introduce a new innovation comprising the use of continuous cement grouting during embedding. The method has been tested on a field test site and installation and permeability features have been observed and analyzed. Installation can be carried out using traditional sheet piling machinery, merely some additional grouting equipment is needed. Installation speed of grouted sheet piles corresponds to that of conventional embedding. The permeability of the tested method is satisfactory in applications where e.g. polluted soil or water has to be isolated from the surrounding environment. In addition, this method can be used for conventional retaining walls where very low permeability is required or for reduction of soil vibration, e.g. close to a railway embankment. The new method to grout simultaneously and continuously during embedding has been developed based on respective innovations on impact driven steel piles.

Jan 1, 2006

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper focuses on determining the favorable geological and hydrogeological conditions for forming uranium occurrences in the Froqlos-Jabal Abou Rabah region, Palmyrides, Syria. Eighty rock samples from this area were analyzed by spectrometric gamma-ray technique to determine the radioactive concentrations of eU and eTh, and of %K. Uranium concentrations in shallow and deep groundwaters were also determined. High uranium concentrations were registered owing to the presence of phosphatic outcrops in the study region. The uranium migration trends and its remobilization were analyzed through the analysis of the behavior of eU, eTh, and their ratio. A positive relationship between eU and eU/eTh, and a negative relationship between eTh and eU/eTh in geological formations of different ages supports the secondary remobilization of uranium. The role of groundwater movement in transportation and redeposition of uranium mineralization is discussed: deep waters are less oxidizing than near-surface waters, and do not appear to have significantly remobilized uranium. This indicates that the source of secondary uranium mineralization is surficial or near surficial, and is mainly related to the leaching of outcropping phosphatic layers.Integration of the results with established radioactive and geological sections reveals four radioactive anomalous zones: north Froqlos, Kherbet Hannora, northwestern flanks of Jabal Abou Rabah (Kherbet Al-Hajar), and the northwestern limit of the Ghuntor depression. The high uranium concentration in north Froqlos is because of its original presence in the phosphate beds and extensive fracturing, which allows groundwaters to penetrate and remobilize the uranium. High uranium concentrations in the other three locations are caused by the presence of evaporites and capillary action, which draws solutions upwards and causes redeposition as surface crusts (gypcrete)."

Jan 1, 2009

By Thomas Barkley

Recent developments in hardware and software have made accurate measurement of Underground Face (Development) Drilling a reality. New and compact laser profiling equipment makes it possible to measure drilled material left on the face as well as the actual tracks of the holes drilled in the rounds. Utilization of these available technologies makes it possible to correctly define the drilling accuracy and the blasting pull. Through the use of actual face round measurements, I will show the level of definition and amount of information that can be collected.

Jan 1, 2003

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Donald B. Lindsay

This report presents the findings of an investigation into the characteristics of a number of techniques for cleaning ambient air with special emphasis on their applicability to the removal of the short-lived radioactive decay products of 222-radon, the so-called " radon daughters" that have been identified with the induction of lung cancer in underground uranium miners. The purpose of the study was to review the requirements for control of radon daughter concentrations in mine air, and to examine all techniques whose feasibility has been demonstrated in principle and which in our judgment would be capable of meeting those requirements. The study has included a review of all pertinent literature, both technical and proprietary, on the subject of the control of miner exposure to the radon daughters and in the area of potentially applicable air cleaning technology. Information about the nature of the problem and about the experience of the uranium mining industry in applying air cleaning methods to its solution was obtained by visiting mines where such methods are in use, and by written correspondence and telephone conversations with other industry sources. Information on performance characteristics and costs of applicable air cleaning methods and equipment was obtained from the experience of our own engineering staff and by visits, interviews, and correspondence with manufacturers of industrial air cleaning equipment.

Jan 1, 1978

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By James Tarr, Matthew Eichler, Brent Tardif

ANFO was being used as one of the blasting agents on a construction site in New England. Groundwater was encountered in numerous blast holes. The blasting contractor was employing typical explosives loading procedures for wet conditions. An abutter to the project complained that blasting caused her well water to have an odd taste and smell. Through testing, it was determined that there were hydrocarbons and nitrates in the well water. Several days later a second neighbor complained of foul tasting water; again it was determined that hydrocarbons and nitrates were present.

Jan 1, 2003