Search Documents

By P. R. Taylor

Laboratory experiments have been performed to evaluate the kinetics of roasting pyrite and arsenopyrite in air at elevated temperatures, in the presence of lime. The effects of temperature, time, air flow rate, particle size, lime type, and mineral/lime weight ratio on the rates of oxidation, lime sulfation, and lime arsenation were studied. The reaction products were identified using chemical analysis, x-ray diffraction, SEM analysis, and optical microscopy. The results are discussed in terms of the utilization of lime to capture sulfur and arsenic during the roasting of refractory precious metal concentrates. More than 99.9% of the arsenic and 98% of the sulfur are contained when roasting pyrite and arsenopyrite with hydrated lime under typical roasting conditions.

Jan 1, 1991

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By A. W. Bryson, K. C. Lenthall

"With the growth in the use of cobalt in industry, interest in its extraction and recovery has increased. With this increased interest comes the need for a fundamental knowledge of the processes involved in the recovery of cobalt metal. This paper examines the effects of cobalt concentration, catholyte pH, operating temperature and current density on cobalt electrowinning with respect to the current efficiency, cell potential and nature of the cobalt deposit. It is found that the cobalt concentration and catholyte pH affect the current efficiency, while current density and temperature affect the cell potential and thus the specific power consumption. Pitting on the deposit is affected by the catholyte pH and the operating temperature. Furthermore, the effect of feed flow-rate on catholyte pH, and thus current efficiency, is investigated. A model to predict the cell performance, which includes the flux of hydrogen ions through the diaphragm, is proposed.IntroductionCobalt metal is a silvery transitional metal found between nickel and iron on the periodic table. Due to its resistance to corrosion and other properties under high temperatures and its good work-hardening characteristics, it is favoured in alloys used in high temperature applications. These include aerospace, aircraft and high speed tools. Other applications include its use as a colourant in glass and ceramics, a drying agent in paints, a nutrient for livestock, a catalyst in the petroleum industry and, in the medical field, in prosthetics and radiology.The main deposits of cobalt are found in Central Africa, specifically Zaire and Zambia, although deposits also occur in Morocco, Canada and Australia. The cobalt is generally associated with other transitional metals including nickel, iron and copper. It is generally extracted by hydrometallurgical means and recovered from solution by electrowinning or hydrogen reduction. Little data [1-2] exists in literature on the electrowinning of cobalt from aqueous solutions. This paper investigates the effects of various operating conditions on the current efficiency, cell potential and deposit nature under continuous operation."

Jan 1, 1997

By James P. Bennett

The U.S. Bureau of Mines, Tuscaloosa Research Center, is conducting a review of the usage of different types of refractories, the current industrial practices to recycle/dispose of spent refractories, and the concerns associated with these practices. This information will serve as the technical basis for initiating a research program to recycle or find alternate uses for spent refractory materials. Approximately 1.6 million metric tons of clay based and 1.2 million metric tons of non-clay based refractory materials were manufactured in the United States in 1992 alone, representing a value of almost 2 billion dollars. Landfill has been and remains the disposal means of choice. Issues such as environmental regulations, concerns over landfill disposal, future liability, and product stewardship programs have brought about increased emphasis for recycling or alternate material use. Information on refractory consumption and the issues associated with recycling or disposing of used materials will be discussed, including current recycling practices.

Jan 1, 1995

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By Shengli Tao, Hongxu Li, Hao Bai, Yu Chen, Daqiang Cang

"China is the world's largest steel producer, in order to give environment load comprehensive analysis of steel and iron industry in china using LCA method, the life cycle inventory was compiled and assessment model based on Gabi software was also established. Environmental impact of two different routes ofBF-BOF and the EAF were analyzed respectively and intercompared. The results show that the modem EAF route is superior to the traditional BFBOF route on almost all the environmental impact indexes, which including acidification potential, eutrification potential, global warming potential, ozone depletion potential, etc. In the whole life cycle ofBF-BOF route in China, the transporting process ranks the biggest contribution part to the overall global warming potential, which can be explained by the fossil fuel burning of transporting vehicles during the long distance from Australia to China as the iron ore used are mainly imported from Australia. Apart from transporting process, Coking, blast furnace and iron mining processes could induce great environmental problems, while for the EAF route, the electricity consumption is considerable, which causing large amount ofC02 emission indirectly. Based on the analysis, several further countermeasures were proposed. Key words: Iron and steel industry, LCA, Gabi software, C02 emissionIntroductionCrude steel of china which reached 101.24 million tons in 1999 ranked the first column in the world since1999, So far has been to keep the world's largest steel output. At the year of2009, China crude steel output of 568 million tons, accounting for 46.6% of the global crude steel production, more than the total sum of crude steel production produced by 20 countries ranked behind. In 2011, China's crude steel production which is expected to be or close to 700 million tons, an increase of 12% than last year, will account for half of the global steel production.The steel industry, however, is intensive resources industry with huge consumptions of energy and water together with mineral resources. Energy consumption of the iron and steel industry has been about 10% of the total energy consumption since 1980. Coal dominants, power next and other energies share least in the energy consumption structure, for example coal accounts for 72.19%, power 23.52% and other total sums less than 5% in the steel energy consumption at year of 2002[2,3]. The consumption of coal discharges much emission of CO2, yet emissions of C02 in China steel industry, secondary only to the power and cement industry, ranked the third, and the coal dominant energy structure and its process have a close relationship. The aim of this research is to target steel production of typical blast furnace-converter (BFBOF) and electric furnace, using GABI software to evaluate and analyze resources and environment influence of LCA, directing at the existing problems in the development of China steel as well as finding the possible way to improve ability of reducing pollution and energy consumption in order to realize the sustainable development of the steel industry [ 4-7]."

Jan 1, 2012

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Isabella Lancellotti, Fabrizio Passarini, Luisa Barbieri, Fernanda Andreola, Ivano Vassura, Luciano Morselli

"The techniques able to incorporate wastes by means of a heat treatment present the advantage to fix the residue with chemical bonds. Among these techniques there are vitrification and sintering which are characterised by different operating temperatures in the range of 950-1500°C and the involved raw materials develop silicatic crystalline phases and glassy matrices capable to immobilize heavy metal contents in the waste matrix. In this work incinerator bottom ash, polishing and glazing ceramic sludges have undergone to thermal treatments in order to valorise the waste as secondary raw material for the obtainment of re-products. The chemical efficiency of the process adopted has been evaluated by comparing the results of release tests applied to the as-received wastes and to the thermally treated materials in order to verify the effectiveness of the different matrices to fix the waste components.IntroductionVitrification is one of the most promising technological options for the treatment of some kinds of waste. The high temperature involved in the process (1200-1500°C) leads to the complete destruction of organic pollutants, such as dioxins, and glassy network formed can incorporate heavy metals. Some vitrification processes naturally occur: glasses produced by volcanic eruptions, such as obsidians (Na2O-K2O-Al2O3-SiO2) and basaltic (CaO-MgO-Al2O3-SiO2) rocks, are basically inert materials even when they contain toxic elements, because these are embedded in an extremely stable glassy matrix. The disadvantage of vitrification is that it is an energy-intensive process involving relatively high costs, therefore its use is better justified if a high-quality product with optimised properties can be fabricated. The most effective way to improve the properties of the vitrified material is the transformation into glass ceramic. This is a fine-grained polycrystalline material (typically from 50% to 98% of the volume may be crystalline) formed when a glass of suitable composition is heat treated and hence undergone to controlled crystallisation (phenomenon named devitrification). The three key variables in the design of a glass-ceramic are: glass composition which controls glass viscosity related to the effectiveness of nucleation and rapidity of crystallisation; glass-ceramic phase assemblage (that is, the types of crystals and the proportion of crystals to glass) which is responsible for many of the physical and chemical properties; nature of the crystalline microstructure (crystal size and morphology and the textural relationship among the crystals and glass) which is the key to many mechanical and optical properties. In particular, a partly crystalline material can be obtained by powder sintering."

Jan 1, 2008

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By L. A. Harris

The formation of coke during coal liquefaction can eventually result in catastrophic failure of the conversion system. Coking typically proceeds by the formation of liquid crystals (mesophase) and the subsequent separation of these crystals from the plastic phase formed during heating of coal. The anisotropy of the mesophase makes it readily detectable in the optical microscope under polarized light. This study examines the solids formed during coal liquefaction processing by optical and electron microscopy. Observations on the relationships between the coke morphology, minerals and inert macerals are presented.

Jan 1, 1982

By Qian Li, Li-chen Hou, Yong-bin Yang, Tao Jiang, Jian-jun Hu, Bing Xu

Extraction of gold from refractory gold concentrates usually requires an oxidation step to remove arsenides、sulphides and carbonaceous matter. In this investigation, the gold concentrates were two-stage roasted under different atmospheres and temperatures. Results indicated that at the first stage, under neutral atmosphere, the removal rate of arsenic increases as the temperature rises. Under the oxidizing atmosphere, with the increase of temperature, arsenic content in the residued calcine increases, in addition, the volatilization of arsenic is also affected by the oxidation of carbon that generated CO, which is advantageous to the decomposition of arsenate decomposition. At the second stage of roasting, it is the higher temperature and stronger oxidizing atmosphere, the faster sulfur and carbon oxidated rate is, but at the same time, the calcine appears the phenomenon of consolidation because of the phase of silicate compounds generate.

Jan 1, 2015

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By Run Huang, Xuewei Lv, Lei Lei, Guibao Qiu, Chenguang Bai

"The TiO2-rich slag and pig iron can be produced from ilmenite concentrate by the electric furnace process. In this study, ilmenite concentrate was reduced in a vertical furnace equipped with a weighting data acquisition system. The effects of reducing agent (carbon) amount on the iron reduction were studied. The phase transformation, morphology and chemical compositions of reduced samples were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. It was found that the reductive degree of ilmenite concentrate increased with the increase of reducing time. The phases of reduced samples were mostly iron, rutile, Ti3O5 and Fe2TiO5. The mass loss percentage increased with increasing the carbon amount from 8% to 12%. When the carbon amount exceeded 12%, the mass loss percentage decreased with the increasing of carbon amount.IntroductionIlmenite and rutile are the main raw materials for producing titania pigment and titanium metal. With the development of the titanium industry, huge amounts of titanium resources are needed. As sources of high-grade titania mineral decrease worldwide, more attention should be paid to the processes involving low grade mineral such as ilmenite ore. In ilmenite, MgO and CaO are the gangue parts. Therefore, the ilmenite refining becomes more and more popular. In the previous studies, the methods of ilmenite refining are electric furnace smelting, direct acid leaching, selective chlorination and thermal reduction [1]. Electric furnace smelting method is widely used in the titanium industry, however, which consumes a great deal of energies and has a high CO2 emission. Its essence is to remove iron oxides and obtain a high titania slag. So the thermal reduction of ilmenite concentrate is an important step in titanium industry, which can decrease carbon reagent consumption and save energy.Over the past several decades, many studies have been carried out on the mechanism and kinetics of the reduction of different ilmenite ores, which are as follows: The carbothermal reduction of Panzhihua ilmenite initiated at about 860 oC. In the temperatures ranging from 900 oC to 1400 oC, the reaction rate was changed like a shape of “M”. That was to say that the reaction rate increased with the growth of temperature at first, then decreased, afterward increased again and at last the reaction was arrested [2]. The Mohammad A.R group [3, 4] showed that the carbothermal reduction of primary ilmenite concentrate was faster in hydrogen and initiated at a lower reduced temperature than in argon and helium. The reduction in argon and helium had about the same rate and extent. Titanium oxycarbide started at 1000°C in hydrogen. The conversion of primary ilmenite concentrate to metallic iron and titanium oxycarbide at 1200 °C was completed in 300 minutes. Monoxide as the reductant to reduce ilmenite had been studied intensively by a few research groups [5, 6]. The rate and the degree of reduction depended on the formation of a metallic shell of iron which inhibited the transfer of CO to the reaction zones; titanium had a strong effect on the mechanism and rate of reduction of iron oxides. Wang and Yuan [7] studied the reductive kinetics of the reaction between a natural ilmenite and carbon. At temperature below 1100°C, chemical reaction was the rate controlling step, at 1100 to 1250°C mixed controlling was rate controlling step, above 1250°C diffusion through the product layer controlled the reaction. Zhang [8] investigated the reduction of natural, sintered and preoxidized ilmenite concentrates in hydrogen methane mixtures. Preoxidation and sintering of ilmenite concentrates changed their phase composition and caused a sharp decrease in specific surface area of raw materials and an increase in carburization temperature. Sintering also increased the metallization temperature of iron."

Jan 1, 2011