Search Documents

By H. Hahn, B. H. Kear, K. Kan, S. C. Danforth, G. Skandan, W. Chang

"A new chemical synthetic process for the production of non-agglomeratednano structured ceramic (n-ceramic) powders, starting from metalorganic precursors, is described. The process combines rapid thermal decomposition of a precursor/carrier gas stream in a hot tubular reactor with rapid condensation of the product particle species on a cold substrate. Critical to the success of this Chemical Vapor Condensation (CVC) process are (1) a low concentration of precursor compound in the carrier gas, (2) rapid expansion of the gas stream through an uniformly heated tubular reactor under a reduced inert gas pressure of 1-35 mbar, and (3) rapid quenching of the gas phase nucleated clusters or nanoparticles as they exit from the reactor tube. A wide variety of metal organic precursors is available commercially, all of which can be utilized in the CVC process to produce n-ceramic powders, including single phase, multiphase and multicomponent systems.The CVC process has been used to synthesize non-agglomerated n-SiCxNy and n-ZrOxCy powders, with controlled particle size in the range 2-20 nm. Heat treatment of the assynthesized n-powders in various high purity gas streams causes compositional and structural modifications, including particle purification and crystallization, as well as transformation to a whisker-like morphology. Thus, as-synthesized amorphous n-SiCxNy particles transform to (1) cubic n-SiC particles, when heated in flowing argon at temperatures> 1350 °C, (2) hexagonal n-Si3N4 whiskers, when heated in flowing NH3IH2 at 1400 °C, and (3) cubic nSiC whiskers, when heated in flowing H2 at 1400 °C.Non-agglomerated n-ceramic powders form uniformly dense powder compacts by cold pressing, which can be sintered to theoretical density at temperatures as low as 0.5 Tm' For example, full densification ofn-Zr02 powder compacts under free sintering conditions can be achieved at 1125 °C."

Jan 1, 1994

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By Yu Hu, Gabriella Tranell, Song Zhang, Eivind Johannes Øvrelid

"In the present research, recycling feedstock of silicon for Photovoltic (PV) application is investigated. Whether these recycling feedstocks are reliable in the future use is discussed in this work to assess the properties of the crystal silicon ingot, which is commercially pulled from top-cuts of casted multicrystalline ingot via one kind of Czochralski method - FerroTech. Dopant is the acceptor type Boron (B) and growth direction was <100>. Crystal diameter and the length were 190mm and about 1700mm, which were controlled by the temperature and the pulling speed, then cut to 156mm * 156mm wafers with 2000um and 200um thickness. Resistivity measurements of these wafers by Four Point Probe (FPP) are in good agreement to the calibrated profile after Rapid Thermal Process (RTP). In this work, the Minority Carrier Lifetime MCI, shown by Carrier Density Image (CDI) and Quasi Steady State Photo Conductance (QSSPC), gives the mapping results on the cross section and the relationship to the injection level, increases in an arrange from 40us to 90us along the ingot height, which is abnormal distribution compared to the standard ingot. Then Oxygen and other metal impurities distributions, measured by Flourier Transform Infra - Red (FTIR) respectively, account for the novel phenomenon of the continuously increased MCI. Various types of heat treatments were performed on these wafers (different ingot and different positions) in N 2 and 0 2 mixture atmosphere. Before and after heat treatment, micro-defects were revealed by copper decoration and etching work. Solar cells are fabricated by Energy Research Center of the Netherlands from the experimental ingot, and processed under an industrial standard line. Compared to results of the reference mono-crystalline and multi-crystalline silicon solar cells, the performances of experimental ones show excellent efficiency values up to 18.5%, and Jsc values up to 37mA/cm2.IntroductionThe PV industry has gone through rapid development, with a high growth rate resulting in an increasing demand for silicon feedstock. In addition, costs in production need to be reduced such that solar energy can compete other conventional and renewable energy. Searching low cost, reliable and efficient feedstock is one promoting way to improve and enhance the competitiveness of the PVindustry.More and more researchers start searching new raw materials for PV application [1]-[4]. The key to make full use of low cost raw materials is to control the distribution and effect of impurities, such as Carbon, Nitrogen, and other metal contamination [5]."

Jan 1, 2013

By Duan Xin-hui, Wang Xin, Peng Jin-hui, C. Srinivasakannan, Zhang Li-bo

The work attempts to optimize the process of preparation of modified semi-coke from semi-coke using phosphoric acid (H3P04) as the activating agent using the response surface methodology (RSM). The influences of three major dependent variables, the impregnation ratio, activation time, and activation temperature were assessed on the independent variables yield and the iodine number. The empirical relationship between the dependent and the independent variables were established using the quadratic response surface models, which were utilized to optimize the process parameters. The significance of each of the parameters and interaction among the parameters on the independent variable was assessed based on analysis of variance (ANOVA). The process variables were varied within the range of impregnation ratio (IR) from 1.5 to 4, activation time from 30 to 90 min and activation temperature from 550 'C to 650 'C. The optimized process conditions were estimated to be an IR of 2.29, activation time of 32 min, and an activation temperature of 605°C respectively using the process optimization tool. The BET surface area of modified semi-coke of the optimized sample was estimated to be 915m2/g, with the pore volume of0.71cm3/g, with an average pore diameter of 3.09 nm, with micropore volume fraction being 52.36%. The scanning electron microscope (SEM) images were utilized to visualize the surface pore structure.

Jan 1, 2013

By Richard A. Shulkosky

The American Iron and Steel Institute (AlSO, in conjunction with the U.S. Department of Energy (DOE) jointly funded the development of a mechanical properties model for Hot Strip Mills. INTEG process group, inc. validated an enhanced version of the model under a project funded by the AlSI/DOE Technology Roadmap Program (fRP). The Hot Strip Mill Model (HSMM) version 6.0 allows users to easily set-up their mill configuration, simulate a rolling mill schedule and calibrate the model for a variety of grades of steel. Starting from reheat furnace drop out, the model simulates roughing mill stands (reversing and continuous), heat retention equipment (coil box and covers), finishing mill stands (tandem and Steckel mills), the run out table and the mill exit area. The HSMM uses a series of physical models to calculate both the thermo-mechanical and the microstructure evolution of steel being processed in a hot mill to predict its final mechanical properties. The enhanced HSMM was validated using a multitude of samples from several steel companies. Excellent agreement was obtained for tensile strength. The supporting steel companies have utilized the model for a variety of practical applications. Keywords: Process Modeling, Microstructure Evolution, Mechanical Properties

Jan 1, 2003

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from Copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu10), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, Cu2O bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties of the CaO-FeOX-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation. -

Jan 1, 2003

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Z. B. Moukhametshina

The process of various zirconium alloys iodination by the iodine vapor was investigated. The nature of impurities, conditions of iodination, iodine flow rate, and zirconium tetraiodide condensation rate effect on the metal impurities transfer process was analyzed, both qualitative and quantitative correlations were established. Impurities were classified according their transfer extent. Another classification of impurities transport dependence on iodination process temperature was also offered. Obtained results were compared with impurities transport data in the process of iodide refining available in literature. Some impurities transport mechanisins and iodide-refined metals improvement possibility by means of iodination conditions control were discussed.

Jan 1, 1997

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By M. L. Apel

A conceptual approach to the bioremediation of uranium mill tailings (UMT) is presented., This approach focuses on, biosorption to remediate the. effluent solution and bioleaching remediate the. solid fraction. Comparative biosorption studies were performed with synthetic single metal solutions using a commercially available biopolymer. The maximum rate of metal sorption by calcium alginate was found to be 5.43, 6,39, 6.48, and 9.74 mg dm-3 min-1 for U022*, Ba2+, Cd2+ and Zn2+, respectively. Activation energy (AEa) for barium uptake by calcium alginate beads was determined to be 11.5 kJ, indicating a diffusion controlled reaction mechanism. Thermodynamic values (AG+ AH+ and ASt) of the metal-alginate activated complex, as reported in the literature, were found to be in agreement with those calculated from this research. Results show that this biopolymer can be effectively applied in the removal of select metals prevalent in uranium mill tailing effluents and associated waste streams.

Jan 1, 1991

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By E. T. White, Dean Ilievski

"Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known. This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal ""best"" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.IntroductionCrystallisation operations, including precipitation, are widely used in a number of hydrometallurgical processes to recover a desired component or to remove an undesired impurity. The goals of industrial precipitation processes are to maximise the recovery while maintaining product quality (generally product crystal size distribution, purity and morphology and product handling properties). Knowledge of the precipitation mechanisms and kinetics is invaluable for designing new precipitators or for improving existing units. The mechanistic and kinetic information is generally incorporated into mathematical precipitator models, which are then used for process design and optimisation."

Jan 1, 1996

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By Dean Ilievski

Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known: This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal "best" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.

Jan 1, 1996

By Songsong Wang

Recently, replacing Pierce-Smith converting process with the oxygen bottom-blowing continuous converting technology has become a new research focus. Based on the principle of Gibbs free energy minimization, the thermodynamic model of oxygen bottom-blowing continuous converting multiphase equilibrium system has been established. The elements distribution behavior is calculated at the same burden composition and operation parameters as the industrial production. The results show that the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in crude copper are 0.06, 0.0030, 0.070, 0.38, 0.39, 0.020, 0.017, 0.034, 0.010, respectively, and the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in slag are 0.53, 0.81, 0.020, 0.23, 2.5, 0.0048, 0.0010, 0.0030, 1.49, respectively. The calculated results agree well with the actual industrial production data, indicating that the model can be well applied in the oxygen bottom-blowing continuous converting practice.