Search Documents

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By I. Gaballah

Cadmium is toxic to plant, animals and humans. The council directive of the European Communities No 8315 13lEEC has fixed an upper limit of 200 ppb for the release of cadmium in industrial effluents. The conventional method of neutralization/prccipitation ( NIP ) is inefficient to reach this limit. The objective of this study is to test the efficiency of the trees modified bark to remove cadmium cations from industrial effluents after the conventional treatment by NIP. Laboratory scale tests with synthetic solutions show that the cadmium removal depends upon pH and initial concentration. About 99.9 %, 99 % and 96 % of the metal are removed from synthetic solutions containing 10, 100 and 1000 ppm respectively. Pilot plant trials ( 1 m3 ) with an industrial effluent bearing about 500 ppb of cadmium lead to the almost complete elimination of the cadmium ( final concentration is lower than the analytical detection limits < 20 ppb ).

Jan 1, 1994

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By G. Barbery

The models for particle composition prediction that have been put forward are limited to simple textures and lead to an independance of grade with respect to particle size in broken ore. A presentation is made of a modification in texture description; binary textures, in which each subeonstituent has its own breakage characteristics are introduced. The calibration of the textural model can be made using heavy liquid separation results. The application to the case of coal is presented. Coal washability data present spe¬cial difficulty due to the distribution in the specific gravity of coal, which must be taken into account. Coal s.g. distribution is taken as a generalized exponential distribution. Model calibration is then possible and is shown to be in good agreement with experimental data.

Jan 1, 1987

By Liow Jong-Leng

A survey of the interactions of large gas bubbles formed from top and bottom injection of gases into melts was carried out. Spherical cap bubbles were found not to produce much splash when they break through the bath free surface except for that formed by plunging of the-spout at its edges. In contrast, the bursting of balloons produces cavities which give rise to liquid jets being ejected from the bath free surface. The position of the balloons relative to the bath free surface is an important parameter in the formation of the liquid jet. It is found that the interactions of multiple bubbles close to the free surface is important in determining the splash behaviour of gas injected systems.

Jan 1, 1996

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from &apos;Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By Joseph Gambogi

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of futile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium. In this paper, we discuss all aspects of the titanium industry from ore deposits through extraction to present and future applications. The methods of both primary (mining of ore, extraction, and purification) and secondary (forming and machining) operations will be analyzed. The chemical and physical properties of titanium metal will be briefly examined. Present and future applications for titanium will be discussed. Finally, the economics of titanium metal production also are analyzed as well as the advantages and disadvantages of various alternative extraction methods.

Nov 26, 1999

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were carefully examined during the entire growth stage of bacteria (fermentation). Several very important discoveries were made. For example, the pyrite surface invariably drastically changed its properties at the second day of fermentation. Beyond two days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became insensitive to convective diffusion in solution (stirring).

Jan 1, 1990

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By Ahmet Haxhiaj, Jaroslaw Drelich

"Both composition and porosity of pellets are the main parameters influencing the reductive melting process in water-jacket furnace during the roasting of sulfide lead concentrate. Roasting in a smelter located in Trepçë is done at about 9000C, for pellets which are composed of PbS, CaCO3, Fe2O3, and SiO2. In order to faciltiate the formation of slag in the reductive melting, the pellets must have the proper content of CaO, SiO2, and FeO, and porosity. The plant’s practice indicates that pellets with porosity of 18% do not melt adequately in the water-jacket furnace. The optimum porosity for the proper melting of pellets needs to be 32-40% and can be achieved when pellets are loaded with more than 10 wt.% CaO. Pellets with less than 10% CaO have a limited network of pores, such that reactive gases cannot reach the entire ore structure. Also, the composition of the pellets must satisfy the ratio of CaO : SiO2 : FeO = 1 : 1.2 : 1.8 to facilitate the formation of slag in the reductive melting process.IntroductionAgglomeration roasting of sulfide lead concentrate is an important phase in the production of lead by reductive melting [1-6]. The reductive melting process is a complex process with contradictory effects of several technological indexes which many times are hard to measure and determine. In this process, loading the water-jacket furnace with pellets of optimized composition and structure can reduce the consumption of coke, and achieve high level of lead recovery. Pellets (agglomerates) should be porous, but at the same time they should have necessary mechanical strength. ‘Self-melting’ ability of pellets is controlled by the types and quantities of fluxes blended into the pellet composition. Three major additives and their role are:"

Jan 1, 2011

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By Rajesh Kumar Mishra

About 500,000 troy ounces of Platinum Group Metals (PGM) will be available for recycling each year from spent automobile catalytic converters in North America alone. Platinum Group Metals? from spent catalyst can be extracted by Hydrometallurgical, Pyrometallurgical or Gas Phase volatilization processes. This paper is a review and comparative study of various processes investigated for PGM extraction. A number of processes described in this paper have already been commercialized. The technical and environmental aspects of the important processes are discussed.

Jan 1, 1989

By Kunwar Pal, S. K. Tyagi, A. K. Pandey

"This study deals with the performance evaluation, technical and environmental aspects of different cookstove models (NIRE-02, NIRE-03 & NIRE-04). These cookstove models were designed, fabricated and evaluated following Bureau of Indian Standards (BIS) and their performance was compared from technical and environmental points of views. The theoretical efficiencies of all the cookstove models are found to be in good agreement with the experimental one. Also, the overall performance of these models is found to be in the order of (NIRE-04 > NIRE-03 > NIRE-02) which is also observed to be much better than that of the traditional cookstoves being used by the people in most of the developing countries around the world. The CO2 emission reduction from these models is found to be between 2.0-3.0 tons per household annually which is ultimately in good agreement with the experimental values.IntroductionMore than 2.5 billion people around the world depends on the biomass based resources for cooking and heating applications which includes wood, cattle dung, charcoal and agriculture residue [1,2]. Generally, people of rural area cook their food on unvented open fire, which burn biomass fuel inefficiently besides it creates many thermal and environment pollution hazardous causing health problems in the women and girl children due to more exposure of emissions. Also the consumption of biomass is very high as compared to the fossil fuels due to the fact that the large population of the developing countries lives in the rural area than that of in the urban area. It is estimated that about 3% of the diseases are caused due to incomplete combustion of biomass, which results in the around 1.8 million premature death every year including around 0.9 million death under five year of their age [3,4].Ramanathan and Carmichael [5] recently found that the black carbon of unburned smoke is playing a major role in global warming. The emission factors for different combinations of fuel and stove tested in China for direct and indirect GHGs as well as other airborne pollutants such as, CO2, CO, CH4, TNMHC, N2O, SOx, NOx, TSP etc. for a typical set of operating parameters [6]. The improved biomass cookstove technology came into assistance which is technically feasible, socially reliable and economically viable [7, 8]. The improved biomass cookstove not only reduces pressure on the biomass resource, but also reduces the environmental pollution and also minimize the time required for collection of fuel wood [9, 10]. Sharma et al. [11] emphasized on the adoption and large-scale propagation of efficient stoves to improve the health of rural women and to reduce the consumption of firewood and environmental pollution."

Jan 1, 2014

By Kandipati Sreenivasarao

Ion and precipitate flotation involve adding an appropriate collector to aqueous solutions containing metal ions, to form hydrophobic metal-collector complexes or precipitates that can be removed by flotation. With a better fundamental understanding of the effects of physical, engineering and chemical parameters on the performance, ion and precipitate flotation techniques could usefully complement techniques now available for removing metal ions from dilute solutions. The removal of Cu(II), Pb(II), Cd(II), Cr(III) and Cr(V1) has been studied, using different types of collector, according to the nature of the metal-bearing species. The effects of collector/metal ion ratio, and solution and froth height on the flotation kinetics, bubble coverage by the metal-collector complex, recovery of metal and effluent quality are reported. The observed behavior is related to the solubility products of the metal-collector complexes, which were also determined.

Jan 1, 1994