Search Documents

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By Wenya Du, Qingbo Yu, Peng Li, Qin Qin

"A new heat recovery system is proposed. This system uses the endothermic heat of gasification reaction instead of sensible heat to recover the energy of molten blast furnace slag. The gasification technological parameter in molten blast furnace was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer. The results showed that, according to different gasification agent, this system can produce syngas with different C-H ratio. The exergy efficiency of this system is high and its internal exergy loss rate is about 11%. This method can bring huge economic and environmental benefits which are important to the survival and sustainable development of iron-steel enterprises. The molten BF slag acts as not only thermal media but also good catalyst. The kinetic parameters on gasification reaction with different types of coal used differ from each other.IntroductionEnergy consumption in the iron-making process is about 50%~60% of the total energy input. The blast furnace is very important in the iron & steel process. So energy conservation and emission reduction about blast furnace is very important. In recent years, in order to recovery energy, many new technologies such as TRT (Top gas pressure Recovery Turbine) and CCPP (Combined Cycle Power Plant) were used in iron-making. But the energy of molten blast furnace (BF) slag has only been used limitedly so far.Molten BF (Blast Furnace) slag is the byproduct of iron-making at the high temperatures range from 1723 to 1923K, and has a large amount of sensible heat remaining. The yield of molten BF slag is about 300 kg per ton of pig iron. In conventional processes, molten BF slag is quenched rapidly using a large amount of water to produce a glassy-granulated slag. The quenching slag must be dried before it can be used in cement manufacture. During the process, a large amount of water was consumed and the energy of molten slag can not be recovered. At the same time, it causes environmental pollution problems. So the critical problems of the process are not only energy recovery of molten slag and reducing emission of H2S and SO2, but also guaranteeing the subsequent use value of slag. For this propose, many new technologies were investigated to recover the thermal energy of molten slag. The promising methods are dry granulation [1-4] and reforming of methane [5-9]. The method, utilization of reaction heat instead of latent heat and sensible heat, is quite attractive from viewpoints of energy storage without heat loss, and makes a connection to other industry. But both of them are in laboratory. In this paper, coal gasification in molten BF slag was used to recover the energy of molten BF slag. The gasification technological parameter in molten BF was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer."

Jan 1, 2011

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in' the Fe-Pb-C system are 95A%Fe-4.5%C-0.l %Pb and 99.9%Pb-0.1 %Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx=[masso/uX in molten Pb]/(masso/uX in molten Fe), are 2.2, 2.2 and lA, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Jonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the Ni3S2-FeS matte with either FeOx-CaO or FeOX-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Gregory A. Knapp

Treatment of industrial wastewaters generally advances with specific chemical concentration and mass-flow targets, established by National Pollutant Discharge Elimination System (NPDES) permits. Treated discharges must also address toxicity to test and receiving water organisms. Various parameters might need consideration during treatment design and planning, such as the known toxicants, hardness, alkalinity, solids, nutrients, metals in both the dissolved and particulate state, and even flow. Since toxicity is used as a "catch all" regulatory monitoring tool, design of treatment systems should focus on the various factors contributing to toxicity.

Jan 1, 1996

By V. M. Paretsky

Oxygen-flame converting of a solid ground matte containing heavy non-ferrous metals in a wide range of concentrations is one of the perspective trends meeting the demands of modern non-ferrous metallurgy. As. a result, of semicommercial tests on oxygen-flame smelting of nickel matte containing 13,5-17,5% Ni; 0,45-0,65% Co under continuous autogenous conditions a converter matte containing 68 8-75,0% Ni and 0,48-1-,0% Co and ferrite -calcium slag containing 1,4-8,4 Ni and 0,16-0,56 Co were pro¬duced. Nickel recovery in a converter-matte was 76,2%, copper - 58,'2% and cobalt recovery in. a slag was 90%. Slag cleaning in an electric furnace allowed to after-recover nickel and cobalt in an alloy to produce a dumpy slag containing 0,03% Ni and 0,02% Co. The development of modern' ecologically pure energy-saving autogenous technologies of the treatment of sulphide raw materials containing heavy non-ferrous metals makes certain demands of the perfection of a process of converting rich sulphide-metallic intermediate products obtained at autogenous smelting. These-demands were connected first of all with the fact that converting process stages because of process periodicity are more unfavourable from the point of ecology, power intensity and unit stability. Besides, during rich matte treatment the problems connected with heat shortage when using air blast and heat excess-when using top oxygen blast to treat luquid matte a-rise and when enriching air blast by oxygen up to 26% fast erosion of the brickwork of a tuyere zone takes place. The technology of Outokumpu and Kennecott companies-on solid- copper matte converting in a flash smelting furnace using air blast is not universal as its possibilities are limited by certain composition of mattes. Besides, flash smelting to produce highly basic or combined slags requires larger enrichment-of blast by oxygen or extra fuel feed. Naturally a flowsheet with continuous converting of matte of various composition up to white matte production is simple,

Jan 1, 1993

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By Florian Aurelian, Mihai Popescu

"It will be tested four types of “geochemical barriers”. All those mixtures were contacted with mine waters containing uranium, radium and heavy metals. The loading capacity was determined. The optimum mixture was determined and its efficiency was tested within an uranium areal, where the activity was stopped. It was determined the possibility to recover the radioactive elements and the heavy metals from the investigated barriers.IntroductionThe paper presents the results concerning the performances of some “geochemical barriers” used for the decontamination of mine waters from uranium mining sites, which were tested in lab and in situ.ExperimentalThe research activity was carried out in lab and on the site.In the lab a module was constructed in order to follow up the uptake capacity of the “permeable reactive geochemical barriers” used to remove the radiolelements from the contaminated waters originated from the uranium mining industry. The barriers, which were used, are made of cheap natural materials, which can be easily got (wood chips, peat coal, sawdust, iron span, steel and zeolitic tuff). The following types of barriers were tested:•, 1st barrier: peat coal, sawdust, zeolite on weight ratio of 1/1/1;•, 2nd barrier: bentonite, sand, wood chips, peat coal on weight ratio of 1/1/1/1;•, 3rd barrier: iron span, steel, sawdust, peat coal on weight ratio of 2/1/1;•, 4th barrier: iron span, steel, sand, firry wood chips on weight ratio of 1/1/1.Lab researches concerning the uranium uptake capacity of the above described “reactive barriers” pointed out that the 3rd mixture (iron span, steel, sawdust, peat coal on a ratio of 2/1/1) didn’t reach the maximum uranium uptake capacity not even after eleven contact stages (the uptake capacity being of 70.6 mg U/ kg of mixture) and the mixture of peat coal, sawdust and zeolite has an uranium uptake capacity of 26.6 mg U/kg of mixture and becomes saturated after four contact stages.Each one of the components involved in physical-chemical processes of sorption, reduction and precipitation, will determine the diminution of uranium and other metals contents upstream the permeable reactive barrier."

Jan 1, 2008

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001

By Peter G. Mason

Over the last 15 years numerous Pressure Oxidation and Pressure Leach plants have been installed throughout the world. The technology is no longer regarded with awe and trepidation as plants designed to treat a wide range of feedstocks continue to be successfully brought on line. Important aspects of the design of such plants include feed preparation, slurry pumping, heating and heat recovery, pressure control and let-down, vessel design, safety and provision of associated services.

Jan 1, 1999

By G. Van Weert, A. van Sandwijk, O. W. J. S. Rutten

"Cathodic and anodic reactions in an acidic nitrate medium were studied in reference to the production of electrolytic manganese dioxide from pyrolusite' (Mn02) ores by reductive leaching. Two USA ores were investigated. The reductant for the pyrolusite ore is produced cathodically in an electrolytic cell and can either be nitrous acid (HN02) or nitric oxide gas (NO). In this work emphasis was placed on the nitrous acid leach. In a high-temperature leach in a nitrous/nitric acid medium, manganese and silver are solubilized and iron is not. Anodic electrowinning of manganese dioxide from the acidic manganese nitrate electrolyte yields flaky y-Mn02, similar to that produced from sulfate and chloride electrolytes. Cathodic regeneration of nitrorts acid was studied in a membrane cell in 1.0 M nitric acid and 0.0 to 0.1 M nitrous acid on a' platinized titanium cathode. At cathode potentials ranging from +950 to +700 mV (SHE), cathodic reduction to nitrous acid takes place, at cathode potentials < +700 mV, cathodic reduction of nitrous acid to nitric oxide takes place. A conceptual process is presented and discussed.IntroductionManganiferous-silver oresLarge reserves of manganiferous-silver ores are present in the Southwestern United States and Latin America. These ores are generally refractory to hydrometallurgical methods of treatment, due to the insolubility of the higher oxides of manganese (Mn 4+) in all common lixiviants such as cyanide solutions, dilute sulfuric acid, nitric acid, ammonia, salt solution, thiosulfates, etc. The silver is either bound by the insoluble manganese, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization.Higher oxides of manganese will dissolve if they are first reduced pyrometallurgically to manganous oxide (Mn2+). This is a widely used pretreatment for manganese dioxide ores and subsequent dissolution in sulfuric acid is common. In order to avoid the pyrometallurgical pretreatment with its large energy requirements and gaseous emissions, fully hydrometallurgical processes have been proposed. These processes are based on the presence of a reductant in solution, in order to reduce the insoluble higher oxides of manganese to soluble lower oxides. Aqueous S02 has been proposed and tested on industrial scale by the U.S. Bureau of Mines. After washing, silver could be extracted by cyanidation. The neutralization of the pulp prior to cyanidation however causes problems in filtration and the reagent consumptions are high [1]. More recently, acidified thiourea and bacteria were proposed for the solubilization of both manganese and silver in a single leach step. High extractions were obtained, but drawbacks of these methods are high reagent consumption or slow kinetics [2,3]. For the options of manganese recovery from the leach filtrate, precipitation with persulfate or ammonium carbonate and ion exchange have been proposed. The proposed options for silver reclaim are precipitation with either zinc or Na2S and adsorption onto activated carbon."

Jan 1, 1997

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003