Search Documents

By Chang Wei, Zhigan Deng, Jiqiang Liao, Minting Li, Hongsheng Xu, Yan Song, Cunxiong Li, Xingbin Li

"Abstract: Direct ?otation of oxidized zinc-lead ore is characterized by recovery of zinc and lead only around 55% and 50%, respectively. Mineralogical analysis shows that the sample used in the present study is a carbonate hosted zinc-lead ore, with a zinc and lead carbonate content that accounts for 80.14% and 75.63% of the total minerals, respectively. The carbonate hosted zinc-lead ore was hydrothermally sulfidized with elemental sufur and the experimental data indicated that under the conditions employed up to 75% zinc and 82% lead sulfidation extent were achieved. As a result of pre-sulfidation followed by flotation, the recoveries of zinc and lead into flotation concentrate were over 90%. A flotation concentrate was obtained with 52% Zn and 37% Pb from the materials which was treated by sulfidation.IntroductionSulfide ores are the primary source of zinc and lead, and they are becoming depleted; thus, metallurgical investigators are interested in using abundant oxidized zinc-lead ore reserves. The high-grade zinc-lead oxidized ore, which normally has a zinc content higher than 15%, can be disposed of by acid leaching and electrolysis. However, the low-grade ore, which has a zinc content lower than 10%, is difficult to smelt with pyrometallurgy and hydrometallurgy, and the processes are very complicated and expensive in terms of production flow and energy consumption. Therefore, making the low-grade oxidized zinc-lead ore more beneficial has become more important in recent years. Flotation is the most common process, and the primary method of recovering zinc and lead from sulfide or oxide minerals. It is well known that there is a difference between sulfurized and oxidized minerals regarding their separation by flotation. Flotation of zinc and lead oxidized minerals is extremely complex because of the similarities in the physicochemical and surface chemistry of the constituent minerals. There are no known direct-acting collectors capable of producing single metal concentrates [1-3]."

Jan 1, 2012

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By R. S. Krarner

Fly ash, a by-product of coal burning power plants, poses a major problem for the utility industry since most fly ash must be landfilled. These quantities may represent as much as 20% of the total material going into landfills. A major problem with fly ash utilization is that although the ash consists of useable components, ash composition can vary depending on the types of coal burned and plant operating conditions. Ash is first characterized using SEM, image analysis, and chemical methods. Processing techniques were developed to separate ash into various components including cenospheres, magnetic spheres, carbon, and clean ash. These products are again evaluated for various utilizations before being used to produce valuable products such as mullite, activated carbon, fillers in plastics, and concrete.

Jan 1, 1994

By Huang Kai

Uniform needle-like and spherical nickel oxalate particles were prepared by the chelating precipitation process, which was based on the reaction of oxalate acid and the solution of ammonia nickel chloride. The molar ratio of ammonia to nickel ion in the mixed solution is essential to determine whether the spherical or needle-like particles are formed, which means actually the concentration of ammonia is the key to determine the growth mechanism. When oxalate acid is added in the form of solid, it may act as the nucleation interface for the eariy-precipitated substance and so induce the formation of spherical particles. The PVP agent can improve the dispersing degree of the needle-like particles and higher reacting temperature leads to larger particles. The composition of the needle-like particle consists of ammonium and nickel oxalate instead of the pure nickel oxalate.

Jan 1, 2003

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By Douglas Robinson

This paper describes technical work done to develop a Spouted Bed Electrode Cell into a commercially viable Electrowinning Cell; (a previous paper has been presented at the ECS meeting in Paris in May of this year, with a more general overview of the cell, [1]). The studies have included hydrodynamic tests to understand the criteria for the circulating flow of metallic beads in the cell, particularly in the region at the entrance to the draft tube, and electrochemical tests to find a suitable diaphragm for extended time electrolysis. Various patent pending features were developed including a double nozzle to allow for automatic stopping and restarting of the bed, an arrowhead shaped draft tube to control the flow of beads into the entrance to the draft tube, a roof-top shaped device to control the flow of beads out of the top of the draft tube, an overflow weir to allow the continuous recovery of beads from the cell, and a family of diaphragm fabrics for extended operation. Prior to the identification of the diaphragm material, short circuits would develop within a few hours. A pilot scale cell was operated for three days, with continuous operator attention, and then for ten days with operator attention only on day shift. The cell is currently advancing to the next stage of development which will involve continuous testing in a commercial copper electrowinning facility.

Jan 1, 2003

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By R. L. Miller

Oil -bearing metal sulfide sludges produced in treatment of an industrial wastewater, which includes plating wastes, have yielded to treatment by electrooxidation and hydrogen peroxide processes. The oxidation can be controlled to be mild enough to avoid decomposition of the organic phase while oxidizing the sulfides to sulfates. The pH is controlled to near neutral conditions where iron, aluminum and chromium(II1) precipitate as hydrous oxides. Other metals, such as lead and barium, may be present as sulfate precipitates with limited solubility, while metals such as nickel and cadmium would be present as complexed ions in a sulfate solution. The oxidations were found to proceed smoothly, without vigorous reaction; heat liberation was minimal.

Jan 1, 1992

By Li Yuhai

Kinetics of non-isothermal precipitate process and crystal growth of perovskite (CaO ? Ti02) phase in CaO-TiOz-Si02-AlP3-MgO system were studied. The experimental results show that the relative volume fraction can be described by the equation given by K. Matusita et at. and the experiential expression of average crystal radius was obtained. The particle coarsening in non-isothermal process has important effects on the crystal growth of perovskite phase.

Jan 1, 2000

By Michael S. Moats, Daniel Kim, Shijie Wang

"The behavior and deportment of lead, arsenic, antimony and bismuth are critical in producing high quality cathode by copper electrorefining. A critical review of research related to these elements is presented along with a comparison to industrial data, where appropriate. These elements exist predominantly in the anode as complex oxides along die grain boundaries. Upon dissolution, Group 15 elements report both to the electrolyte and slimes while lead essentially enters the slimes. The deportment of the Group 15 elements appears to be influenced by several chemical interactions which are discussed. The effect of these elements on floating slimes and anode passivation is reviewed. Under normal electrorefining conditions, lead, antimony and bismuth are thought to enter the cathode through the encapsulation of slime particles. The literature indicates that arsenic enters the cathode predominately by electrolyte entrainment. Finally, areas for future research regarding these elements are presented.IntroductionControlling lead, arsenic, antimony and bismuth is critically important for the production of high quality cathode in copper electrorefining. The reasons for this are twofold. First, ASTM Grade 1 Cathode specifications [1] for these elements are low, as listed in Table 1. Second, they can affect the efficiency of the electrorefining process (e.g., through passivation, current efficiency, slime processing)."

Jan 1, 2012

By David Roha, Øyvind Mikkelsen

"Significant resources have been spent throughout the years in the investigation of production of aluminum by carbothermic reduction. Due to the technological challenges involved, the efforts have not yet resulted in a commercial process. An initiative to overcome issues that prevented previous attempts to succeed was taken by Alcoa through the Advanced Reactor Process. The research program has resulted in technical developments which have resolved many of the previous issues. The knowledge about the process has continuously improved through physical and computer modeling as well as by experimentation at various scales. The technical achievements together with improved process understanding have resulted in a reactor design able to continuously operate the process for several weeks at the time, with hundreds of kilograms of alloy in every tap.IntroductionThe Hall-Heroult process has since its invention in the late 19th century, been essentially the only process used for commercial production of primary aluminum. The process has so far proved to be superior to all potential process alternatives and has continuously been improved. Although the Hall-Heroult is a reliable process it also has challenges:"

Jan 1, 2012

By T. Alboussiere, O. Paireau

"We have designed an experiment to simulate natural convection in a direct-chill aluminium ingot. In this experiment we induce natural convection within a hemisphere filled with liquid-metal (mercury). The device consists of a copper hemispherical bowl closed by a copper plate. The top is maintained at superheat temperature while the boundary is cooled. While the temperature measurements were found using thermocouples, the velocities were obtained using an original technical procedure that relies on MHD properties. By applying a steady local magnetic field, we measure the velocity. The distribution of temperature and velocity can be separated into a thermally stratified core bounded by thermal wall jets. These wall jets greatly influence the degree of macrosegregation in ingots.1. Natural Convection in Aluminium CastingIt is well known that the quality of the final product in aluminium casting depends on the movements within the liquid metal such as forced or thermogravitational convection. Strong buoyancy-driven flows are known to occur in the liquid metal pool of an aluminium ingot caster. These flows have a significant influence on the metallurgical structure of the ingot through the redistribution of heat, fragmented dendrites and segregated material within the pool. Macrosegregation mechanisms depend on favourable temperature and flow distributions in the sump, and these factors will determine the pattern and degree of macrosegregation. Moreover, for many years, the importance of thermally-driven natural convection in casting has been underlined (Cole & Bolling, 1965). In this way, a precise determination of the velocity and temperature fields is required in order to improve understanding of the macrosegregation mechanisms. That is precisely the aim of this paper, which provides experimental data of the flow and the temperature distributions in a natural convection experiment. We intend, with this laboratory experiment, to determine accurately the velocity field, particularly within the thermal boundary layer where the effects of the flows may have an important role in the transport of crystals."

Jan 1, 1999

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By Norman L. Kotraba

Zia Metallurgical Processes, Inc. has developed and patented a steelmaking process capable of converting iron bearing metallurgical wastes into high quality steel products. The process utilizes a proprietary design rotary hearth furnace to convert iron bearing wastes, pelletized with coal, or other forms of carbon, into direct reduced iron (DRI). This DRI is fed, hot, from the rotary hearth furnace into a Zia All Purpose Vessel (ZAV) where it is smelted and refined into high quality steel. A specially designed turret with three independent arms, each supporting a separate ZAV, comprises the heart of the meltshop. No overhead cranes are required to transport molten metal from the smelting/refining operation to the ladle metallurgy station to the caster to an inspection station and back to the smelting/refining point. The molten steel is contained in the ZAV throughout the operations eliminating the possibility of steel con¬tamination by non-metallic inclusions occasioned by the exposure to ambient air during metal transfer into ladles. The result is the creation of very clean steel that can be alloyed to produce virtually any desired grade from stainless steel to common structural steel.

Jan 1, 1994

By Liu Zhonghua

Hydrogen reduction of cobalt sulfide (Co9S8) was experimentally investigated in the temperature range 813-1053 K. The results revealed that the reaction kinetics can be described by the shrinking core mod¬el in chemical control regime at low temperatures, it is of first order with respect to hydrogen concentration, and the reaction activation energy is 67.4 kJ/mol. The SEM second electron images of the samples before and after experiments showed that the swelling of the sample above 973 K is due to the formation of metallic cobalt whiskers.

Jan 1, 1992