Search Documents

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated control systems have been developed for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000

By Wing Ka Ng

Substitution of pulverized coal injection by solid biocarbon fuel has the potential to achieve substantial reduction in GHG emissions associated with blast furnace ironmaking. A systematic evaluation was conducted on the performance of solid bio-carbons produced from a single raw biomass source using different pyrolysis technologies. The potential of solid biocarbon in reducing GHG emission of the blast furnace ironmaking process is strongly influenced by its O/C mass ratio. In order to achieve substantial GHG reduction, it is necessary to replace coal injection by solid biocarbon having a low O/C mass ratio. The pyrolysis technology and conditions employed are key parameters influencing O/C mass ratio of the resultant solid biocarbon. Close collaboration between steelmakers and solid biocarbon producers is critical for producing suitable solid biocarbon fuel to replace pulverized coal injection. A successful partnership should pave the way in achieving substantial reduction in GHG emissions of the blast furnace ironmaking process.

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By M. A. Halim, V. I. Lakshmanan, T. Sheikhzeinoddin, R. Roy

"Chloride metallurgy is emerging as an alternative process for the production of base metals. Process Research ORTECH Inc. (PRO) has been at the forefront of technological development of chloride metallurgy. PRO has developed an innovative technology for the production of high purity titanium dioxide, iron oxide and vanadium pentoxide from ilmenite ores and concentrates. PRO is also developing its proprietary mixed chloride technology for the extraction of vanadium from other sources such as oil shales. In this paper, results from the test work conducted at PRO for the extraction of Ti and V using a mixed chloride lixiviant are presented.IntroductionTitanium and vanadium alloys and compounds have numerous industrial applications. Titanium dioxide is used in paints, plastics, rubber, paper, inks, textiles and a number of other miscellaneous applications. Currently nanosize T1O2 is being investigated for application in the cosmetics industry. Inorganic sunscreens mainly use T1O2 or ZnO particles, which reflect and scatter ultra-violet light. T1O2 nanomaterial is also finding application in smart construction materials and coatings, as a photo-catalytic converter. Nano TiO2 can catalyze the dissociation of NOX gases and other automotive emissions, thereby reducing the smog in urban centers. After the construction material is exposed to sunlight or ultra-violet light, the T1O2 is photo-activated and degrades the pollutants.Titanium metal and titanium dioxide are produced from ilmenite (FeTiOs) or rutile (naturally occurring T1O2) ore. Only about 6% of the titanium resources are used to produce titanium metal and the rest is used to produce T1O2. Many of the titanium ore deposits currently have unacceptable levels of transition metals which limits their processing by conventional routes."

Jan 1, 2012

By Liwen Hu, Jianxun Song, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

The subchloride titanium was prepared by sponge titanium and titanium tetrachloride in the CaCl2 at 1173 K. The species were detected are mainly titanium dichloride, and the average valent in the melt are 2.05. The accurate equilibrium constants were obtained for the reaction 3Ti2+ = 2Ti3++Ti after the accurate activities of titanium chloride were evaluated with emf method, and the observed deviations from ideal behavior are discussed.

Jan 1, 2015

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By B. Manana

In heap leaching, the oxidative dissolution of value minerals encapsulated deep within large particles cannot be fully understood on the basis of the bulk solution conditions relative to variable solution conditions near the mineral surface. In the present study, the diffusion of the oxidising species through inner particle pores is simulated in a model apparatus that separates an inert platinum electrode under controlled reduction potential from the bulk solution through narrow pores of varying length. The Cu-NH3 system was selected as a model system and Cu(II)/Cu (I) as the redox couple of interest. Platinum probes inserted in the pores allowed the measurement of varying redox potentials along the pore length. Results showed that in a 10 mm pore, there exists a narrow (0.5 mm) zone near the reduction surface that is depleted of the oxidant and in which its supply is strongly diffusion limited, even if it is in abundance in the bulk solution. The consistent presence of this narrow diffusion region across all experimental results indicated that the transportation of the reduced species away from the reaction surface had the most significant influence on the potential variations within the pore. This was further supported by the minimal effect of varying concentrations of both Cu(II) and dissolved oxygen on the solution potential within this region.

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015

By J. Brent Hiskey

The global copper industry faces a technological challenge to develop processing schemes for more complex and impure ores and concentrates. Group 15 elements (As, Sb, and Bi) represent impurities that are troublesome both in terms of environmental impact and metallurgical processing. The so-call "dirty" copper concentrates are either unacceptable for smelting and refining or incur high penalties. The behavior of the Group 15 elements is of critical importance in maintaining product quality and process performance. During copper electrorefining, these impurities are released to the electrolyte by electrochemical dissolution of the anode. Depending mainly on temperature, concentration, and oxidation state these elements can spontaneously coprecipitate from the electrolyte. Some of these precipitates are referred to as floating slimes and their formation can have extremely detrimental effects on cathode purity. In this paper, the mechanism of floating slimes formation will be discussed and the fundamental thermochemistry will be reviewed and analyzed in relation to solubility properties.

Jan 1, 2012

By Chr. Kersch

This project further develops supercritlcal fluid extraction as an industrial soil remediation process. Heavy metals are removed from sand using CO2, The effect of the type of complexing ligands, pressure and water content on the extraction efficiency is investigated.

Jan 1, 1999

By F. Kongoli

A computerized thermophysicochemical database is being developed for various processes involved in nickel smelting and converting. This database includes optimized models for slag, matte, liquid and solid alloys in the multicomponent system(s) as applied to batch and continuous nickel smelting and converting processes. This database can be used to quantify the multicomponent and multiphase slag/matte/alloy/gas equilibria, liquidus and solidus surface, tie-lines, solubility and/or losses of nickel and other components in the slag, distribution coefficients, components activities, heat and mass balance, etc. The database also includes optimized models for the viscosity of the slags associated with any of the above processes. Both databases are coupled and this constitutes a very effective method to quantify the effect of each component on several parameters of the smelting and converting processes and to diffuse the confusion that exists in the literature. Several application examples have been given to demonstrate the usefulness of this database for quantitative prediction of the thermophysicochemical properties of the phases involved in actual or developing processes, even in the areas where experiments are difficult or impossible. The considerable cost reduction that results ftom the use of this database as compared to other methods in the improvement of existing technologies or in the development of new ones is discussed along with continuing new developments of this database.

Jan 1, 2002

By S. Raghavan

The thermodynamic activities of MgO in the solid solutions that can exist in the system NiO-Mg0-Zn0 are determined by measuring the EMF of the cell: O2 (g), Pt / MgO, MgF2 // MgF2 // x MgO + yNiO + (1-x-y)ZnO / Pt, O2 (g) / MgF2 in the temperature range 1190-1237 K. Equilibrium phases were prepared along the quasi- binary lines MgO/NiO = 0.1765,0.3333, 1.0,3.0 and 5.667 with the ZnO contents being 0.1, 0.2, 0.25, 0.35, 0.5, 0.75 and 0.9. The crystal structures of the phases were identified by X-ray diffraction. Results obtained so far show that a single phase MgO-rich cubic solid solution exists upto 0.2 ZnO content and for compositions above 0.25 ZnO, a second ZnO rich wurtzite phase forms in addition. Activity measurements show that for low MgO and ZnO contents, the MgO activities exhibit ideal to slight positive deviation from ideality and at higher MgO contents, a negative deviation is shown. Further studies are in progress.

Jan 1, 1993

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces, They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-OB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderúrgica de Tubarão, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces. They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-DB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderurgica de Tubarao, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011