Search Documents

By Geoffrey A. Brooks, M Akbar Rhamdhani, Md Saiful Islam

A novel electrically-enhanced metal purification using slag has been developed. This was achieved by applying DC potential between liquid metal and slag phases. The concept was demonstrated through small-scale experiments at temperatures of 1500-1600oC for the removal of boron from Si-B melt using CaO-SiO2-16wt%Al2O3. Silicon (containing B) and slag were reacted in an alumina crucible in a resistance tube furnace. A circuit was produced by immersing graphite rods into the silicon bath and the slag layer. Electrical potential differences of up to 3.5 V were applied during the reactions. The reaction rates, the opencircuit voltages and short-circuit currents (in the case when the potential was applied) were then measured and determined for various slag to silicon ratio. It has been shown from this study that both the apparent rate and the boron partition ratio were increased by a factor of approximately 1.6.

Jan 1, 2014

By Bemd. E. Langner

At Norddeutsche AfFmerie the CollaMat is an important instrument for controlling the activity of glue in copper electrolyte. Thanks to on-line measuring of the glue activity appropriate action can to taken in the event of sudden changes, such as an intemption in the glue supply, as well as long-term trends, such as continuously decreasing glue activity over days or weeks. Laboratory tests on the dependence of glue degradation on temperature have shown that relatively small increases in temperature of only 3OC cause the half change value of the glue degradation to reduce by 25 %. It is a similar picture with the sulphuric acid concentration in electrolyte. An increase in the acid concentration from 160 g/l to 200 g/l can - depending on the temperature - likewise result in a decrease in the half change value of up to 25 %.

Jan 1, 1995

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Warren J. Bruckard, Mark I. Pownceby, Sazzad Ahmad, M. Akbar Rhamdhani

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Jan 1, 2015

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Sutham Niyomwas

Biomorphic Cellular TiCIC ceramics were produced by vacuum-infiltrating carbon preforms with Ti02 sol and subsequent synthesis by the carbothermal reduction process. The carbon preforms used in the study were obtained by pyrolysis of parawood and neem wood. The effect of infiltration time on the composition and microstructure of the biomorphic TiCIC ceramic was analyzed by X-ray diffractometry and scanning electron microscopy. The biomorphic structure of the TiCIC ceramic is consistent with that of the biotemplate natural parawood and neem wood.

Jan 1, 2008

By Nagy El-Kaddah

"One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100 u. inclusions· are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate the capability of the system for producing super-clean metals.IntroductionThe nature of extraction, refining and processing of metals is such that oxides and other non-metallic particles will always be present. This is due to the highly reactive nature of metals with oxygen and other non-metallic elements. The presence of these type inclusions in metals, even in minute amounts, can seriously flaw the reliability and performance of the final product. They not only reduce the strength and the stiffness of the metal/1/, they are the reason behind many of manufacturing defects such as porosity in castings, surface and internal cracks in continuously cast ingots and rolled products, etc., which act to cause premature failure of manufactured parts. In fact, for critical applications such as turbine blades, there is virtually no tolerance for inclusions above ten microns in size /2/. Therefore, removal of inclusions from the liquid metal is an essential processing step.The demand for cleaner metals has brought major changes in the technology and practice of metal refining and casting. Inclusion removal from the melt is currently achieved by passing the melt through a series of melt treatment systems, including induction stirring furnaces, argon-stirred ladle, and ceramic foam and deep-bed filters /3,4/. These systems are generally capable of removing all inclusion particles above 50 microns in diameter, which meets current cleanliness requirements for most applications. However, they may not be able to meet the projected cleanliness levels for critical applications due to kinetic and operational limitations of these systems in removing smaller particles /5/."

Jan 1, 1996

By Luis W. Pommier

The developed processes, the subject of this paper, extract the hydrocarbons, halogenated organic compounds and metal contaminants from hazardous soils, rendering them non-hazardous and ready to be placed back on the ground. The processes first segregate a non-contaminated fraction from the contaminated soil. This initial task is performed using available minerals processing technology: sizing, gravity separation, magnetic separation, froth flotation, etc. The remaining contaminated fraction, is submitted to two leaching operations for the removal of organic and metal contaminants, whenever both are present or to a single leaching operation if only one type of contaminant is present. The decontaminated soil fraction is mixed with the non-contaminated fraction and is placed back on the ground. The leaching liquors, used at neutral pH, are non- hazardous. After decontamination the liquids are processed to extract the contaminants, now valuable materials, for commercialization. Organic contaminants are removed by distillation of the solvents. The metal contaminants are precipitated in their oxide form. In both cases the regenerated solvents are recycled. The decontamination processes are economically competitive with transportation and disposal of the soils to permitted facilities for hazardous materials, and most importantly the developed processes remove the liabilities from the Responsible Parties. The law establishes that these liabilities do not disappear with either fixation nor with transportation and disposal since the environmental liabilities are of the ? cradle to grave? type.

Jan 1, 1994

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By Eric J. Grimsey

Nickel smelting and converting can be viewed as processes in which iron is either partitioned or transported between matte and slag. Metal recovery depends on the mass of iron transported to slag, the thermodynamic environment in which the transport is made, and the extent to which the slag, once formed, is left in contact with the matte. The importance of these effects is discussed with reference to a new equation which describes metal recovery in terms of a mass balance and a thermodynamically related parameter which is easily measured in practice.

Jan 1, 1993

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By T. -M. Guo, M. J. Braun

"This paper presents an experimental and numerical study of melt flow near the solid-liquid interface and its effect on the interface curvature in a horizontal unidirectional solidification system with succinonitrile. Melt flow is introduced by increasing the ampoule channel thickness. Visualization techniques are employed to observe the flow field and the solid-liquid interface curvature. A numerical model is also developed to simulate the heat transfer, melt flow and phase change in the system. Quantitative information on the flow and temperature fields is generated. A good agreement is achieved between the experimental observations and model predictions. The results could be used for the study of the effect of the melt flow on interface morphology during solidification.IntroductionClassic unidirectional solidification experiments of transparent alloys are conducted with thin film samples sandwiched between two glass slides to investigate the development of interface morphology during solidification [1]. Samples with small channel thickness are usually used to suppress any melt flow due to natural convection and solidification in the channel would then be in the diffusive regime so that the solidification theory can be significantly simplified [2, 3]. Effects of melt flow, in particular due to natural convection, on solidification have also been studied extensively in those systems with large geometrical dimensions [4-6]. These studies indicate a strong effect of the melt flow on interface curvature during solidification [5, 6]. Only limited efforts were made to address the effect of the melt flow on interface morphology in horizontal unidirectional solidification, in particular for the cases when the channel thickness is not thin enough to suppress completely the natural convection [7]."

Jan 1, 2004

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By Irshad A. Rana

In a modern copper smelter, the capital cost of a sulfuric acid plant constitutes the largest single cost item of the total investment. It is thus essential to properly size the acid plant in order to reduce its capital cost and enhance the economic viability of a new smelter project. Whereas the off-gas from a smelting furnace is continuous and generally uniform, the gas flow from the Peirce-Smith converters is intermittent with significant fluctuations. The converters off-gas volume is dependent upon a number of interrelating factors. The most significant factors are the matte feed grade, the system air infiltration, the converter's size and blowing rate, the maximum number of converters simultaneously blowing and the gas cooling system employed. The acid plant size, therefore, is heavily influenced by the converter off-gases. Several of these factors are discussed, and their impact in determining the acid plant size is explored.

Jan 1, 1993