Search Documents

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs. Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads. Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Jan 1, 1999

A two-dimensional time-dependent analysis of a overburden-coal pillar-weak floor strata interaction problem is presented as a beam model consisting of a composite roof beam resting on multiple elastic foundations (pillars) underlain by a composite rock mass representing immediate floor strata. Several different material models may be considered for the immediate floor strata. The analysis can include all openings and pillars in a panel and permits bed separations in the roof composite beam. The model has enabled identification of the relative significance of different geometric and mechanical behavior parameters which govern the system. The paper presents the theoretical background for the model as well as its application to a mine in Illinois where surface and underground geotechnical observations have been conducted over the last two years.

Jan 1, 1988

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By Venkata S. Vutukuri

Compressive strength of cylindrical specimens of a model material and sandstone with various diameter/height (d/h) ratios was determined in unconfined compression tests. It was observed that the compressive strength increases with increase in d/h ratio. Triaxial compression tests were also conducted on the specimens of the same materials with a d/h ratio of about 0.47. It was observed that the axial stress at failure increases with increase in confining pressure. A very interesting correlation was found between the effect of d/h ratio on compressive strength in unconfined compression tests and the effect of confining pressure on axial stress at failure in triaxial tests. The relationships between d/h ratio and confining pressure, s3 in MPa are:- For model material - s3 = -0.95 + 1.7957*(d/h) 0.7883. For sandstone - s- (-0.4554 + 0.9888* (d/h) 1.0355. The correlation coefficients for these equations are 0.9997 and 1. These equations are valid for d/h ratios of up to 10.

Jan 1, 1993

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By S. Y. Liu

Based on the underground measurements, physical model test of simulated materials in the laboratory and finite element analysis, this paper demonstrates the pattern and process of roof fall over the tip-to-face area in the fully mechanized coalfaces. The main factors that affect the stability of the immediate roof are thoroughly studied including the fracture position and tilt angle of the main roof, the tensile strength (Rt) and cohesive force (c) of the immediate roof, and type and resistance of the powered support. Based on these factors, this paper proposes the basic process of immediate roof breakage a. follows: As the longwall farm advances, the main roof breaks and then rotates. A tensile fracture zone will be formed in the immediate roof under the fracture line of the main roof. A caving zone (plastic zone) will be formed in unsupported area between coalface and canopy tip. If these two zones overlap the immediate roof will be completely unstable. Under this condition, powered support will have difficulties lo control the rod. Therefore it is necessary to study the process of immediate roof breakage and look for effective methods for controlling the roof.

Jan 1, 1990

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By Steve P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39 instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6 m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor varia¬tions in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

Jan 1, 2001