Search Documents

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008