Search Documents

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By Gang Ren, Behrooz Ghabraie

"Observational data suggest that the ground surface subsidence profile from multiple-seam longwall mining is rather different from that of single seam. Despite the increase of coal production from multiple-seam mining, available predictive methods are mostly unable to predict a reliable subsidence profile for multiple-seam extractions. In this paper, a case study of multiple-seam subsidence is modelled using physical modelling techniques. The subsidence mechanism as revealed in the physical model is explained and the differences between multiple and single-seam subsidence are highlighted. On the same case study, a commonly used influence function method (IFM) and Generalised Influence Function Method (GIFM) are utilised to predict the subsidence profile. The results are compared with predictions achieved by a newly developed predictive method based on the understanding of mechanism of the multiple-seam subsidence. Results show a significantly improved correlation between the newly developed method in comparison with the conventional IFM and GIFM. INTRODUCTIONField observations and subsidence monitoring data from multiple-seam coal mining cases show a different subsidence profile as compared with single-seam ones (Sheorey et al., 2000; Li, et al, 2007; Luo and Qiu, 2012; Unlu et al, 2013). The multiple-seam subsidence curve is generally deeper and steeper than of single-seam cases, and varies from one mining configuration to another. Various researchers had made efforts to understand the mechanism behind this phenomenon and the interaction between the two mining horizons (Li et al., 2010, Sui et al., 2014; Zhang et al., 2014). However, the mechanism of the multiple-seam subsidence is yet to be comprehensively understood (Suchowerska, 2014; Ghabraie et al., 2015b).In addition, differences between the single and multiple-seam subsidence profiles make it difficult to adapt single-seam subsidence prediction tools for predicting the subsidence over multiple-seam cases, unless significant modifications are applied This requires understanding the mechanism of the multiple-seam subsidence as the first step to achieve reliable predictive results.The mechanism of the subsidence due to a multiple-seam case study can be investigated via physical modelling. The physical model allows observing the substrata movement as well as the interaction of the two mining activities. An understanding of the mechanism of the multiple-seam subsidence can be developed based on these observations, which would provide basis for developing a subsidence prediction tool."

Jan 1, 2016

By Yi Luo

Subsurface strata movements and deformations associated with underground mining activities could cause problems to subsurface structures and water bodies. By incorporating the methods for surface subsidence prediction with the subsidence parameters derived from collected subsurface subsidence data, methods have been proposed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining. Two new' types of strata deformations in the field of subsidence research, vertical and total strains that could he useful in assessing subsidence influences to the subsurface structures and water bodies, have peen introduced.

Jan 1, 2000

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

The U.S. Bureau of Mines (USBM) has developed the coal Mine Roof Rating (CMRR) to aid in ground control. This paper describes the application of the CMRR at four coal mines operated by a major U.S. coal company. The mines are widely separated geographically, and cover a wide variety of geologic conditions and mining methods. The study found that the CMRR was a useful predictor of roof performance. In mines where the CMRR varied, and other parameters held constant, roof falls were associated with low CMRR values. Important similarities in roof performance were found in mines with similar CMRR values, despite radically different geologic environments. The analyses also indicated that statistics can be used to evaluate ground control performance. For these mines, a "roof fall probability" can be estimated from the CMRR and the intersection span. A spreadsheet program has been developed to facilitate treatment of CMRR data, and it is briefly describe

Jan 1, 1994

By Kot Unrug

For the purposes of underground mine design, twelve cores of the Springfield (V) Coal (Pennsylvanian) roof and floor were retrieved. Each core was photographed, described fresh in the barrel, and the rock quality designation (RQD) was measured. Cores were wrapped in plastic and delivered to the rock mechanics lab. At the lab RQD was remeasured and new photographs were taken before running geotechnical tests including weatherability. Significant differences in barrel RQD's vs. lab RQD's have been noticed in spite of careful handling. The drill site RQD is generally used to calculate geotechnical results, but in some types of coal measure rocks, further fragmentation of core takes place with slight changes of moisture content, which occur even in well wrapped core. This creates a dilemma which RQD should be used for support design. Rocks around excavations are exposed to the significant changes in moisture content due to the seasonal weather changes and related fluctuation of humidity of air ventilating a mine. Therefore, it appears to be more realistic using laboratory RQD which corresponds closer to the actual rock condition around the excavation. Weatherability test, developed for characterization of time dependent behavior of rock exposed to fluctuations in moisture content, is thought to be related to the above-mentioned changes of RQD. In weak shales, mudstones and claystones which weather rapidly, it is essential to characterize their future behavior in the pre-mining stage. This can allow for a realistic design of primary, and particularly secondary support in coal mines, especially in coal fields where such geologic conditions exist.

Jan 1, 2003

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Claude A. Goode

Large quantities of high grade coal exist in thick seams in the United States. Many of these thick seams are too deep to be surface mined and do not lend themselves readily to underground extraction. To develop the new mining technology required to effectively mine thick seams, the Department of Energy has entered into a Cooperative Agreement with Mid- Continent Resources, Inc. to demonstrate the multilift longwall mining technique in a 28 foot-thick seam at their L.S. Wood No. 3 mine near Redatone, Colorado. The seam will be extracted in two lifts, with a 5-foot natural partition of coal left between the upper and lower lifts. Proper selection of face supports is critical to the success of this project. Specifications were defined for the roof supports, and it was concluded that the supports selected must provide full coverage, yield at the legs, and have a 60-inch push- out cantilever that can be set at any position under full load. A Hemscheidt two-leg shield was judged as the best qualified candidate and was selected for the multi-lift trial.

Jan 1, 1981

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By Peter Zhang, Dan Neilans, Scott Peterson, Scott Wade, Joe Pugh, Ryan Mcgrady

"A coal outburst is a severe safety hazard in room-and-pillar mining under deep cover. It is more likely to occur during pillar retreating. Multi-seam mining dramatically increases the risk of coal outburst within the influence zones created by remnant pillars and gob-solid boundaries. Though coal outburst is generally associated with heavy loading of coal pillars, its occurrence is difficult to predict. Risk management provides a proactive tool to minimize coal outburst in room-and-pillar mining under deep cover. Risk assessment is the first step in identifying and quantifying outburst risk factors. The primary risk factors for coal outburst are overburden depth, roof and floor strength, geological anomalies, mining type, multi-seam mining, and panel width. A risk assessment chart can be used to proactively screen out mining sections with high risk of coal outburst for further analysis. Gob-solid boundaries and remnant pillars are critical factors in evaluation of the coal outburst risk of multi-seam mining. Risk identification, risk assessment, geologic influence mapping, geotechnical evaluation, risk analysis, risk mitigation, and monitoring are essential elements of coal outburst risk management process. Training is an integral part of risk management for risk identification and communication between all the stakeholders including management, technical and safety personnel, and miners.INTRODUCTIONA coal outburst is a sudden violent burst of coal from a pillar with broken coal or blocks of coal forcibly ejected into open entries. A coal outburst is a severe safety hazard as the mining crew is highly exposed at the site when the event occurs. Though deep cover and strong roof and floor are underlying geologic conditions of a potential burst incident, its real occurrence is also the result of additional mining factors. In room-and-pillar mining, a coal outburst could occur during both development and pillar retreating, but the latter greatly increases the risk of outburst. The other risk factors of coal outburst also include mining layout, multi-seam mining, presence of adjacent gob, cutting sequence, and local abnormal geologic conditions. Over the years, the cases of coal outbursts have been studied by many researchers and mining practitioners(Peng, 2008; Newman, 2008; Iannacchione and Tadolini, 2008; Gauna and Phillipson, 2008; Hoelle, 2008; and Newman, 2002). It is commonly believed that the coal outburst is the result of a sudden release of elastic strain energy stored in coal pillars and is highly associated with cutting into heavily loaded coal pillars, but its occurrence is a rare event and is difficult to predict. A number of engineering controls have been recommended to mitigate outburst potential. For room-and-pillar mining, sufficient pillar sizes have been the primary control for coal outburst prevention. The pillar design tools such as ARMPS and AMSS developed by NIOSH have played an important role in the design of stable pillars to prevent pillar collapse and squeezing as well as coal outbursts. In fact, with the implementation of pillar design using proper stability factors, pillar collapse and squeezing have been almost eliminated, and the number of coal outbursts has been greatly reduced in the US over the past decade. However, after a few outbursts occurred during pillar retreating in the US over the past a few years (MSHA, 1996; MSHA, 2014; MSHA, 2013), it has been realized that sufficient pillar size is still not enough to prevent coal outbursts. The investigations of the incidents showed that other factors such as multi-seam mining, panel layout, cutting sequence, and local geologic factors also seemed critical in causing the events. Therefore, it has become imperative that additional proactive measures beyond proper pillar design be implemented to prevent coal outbursts."

Jan 1, 2015