Search Documents

By J. W. Jang, I. Iwasaki

Introduction Grinding ball wear in wet grinding is due to a complex combination of abrasion, corrosion, impact and their interactions. The ball charge is continually falling from a height greater than half of the ball mill's diameter, and contact is made with ore particles or other balls. Abrasive wear occurs through penetration and plowing of media materials from the ball surface by hard ore particles (Gangopadhyay and Moore, 1985). Electrochemical interactions between the abraded and unabraded areas of the ball surfaces, as well as between the grinding media and the minerals, occur in grinding mill pulps (Adam et al., 1986). The wear depends on the media composition, the hardness and the corrosive/abrasive characteristics of the slurry. The marked-ball-wear test method was used to evaluate the performance of grinding media under nitrogen and oxygen atmospheres. Also, the wear mode was studied by observing the grinding media surface under a scanning electron microscope. In general, grinding media of high hardness and high chromium contents were found to have better corrosive wear resistance than those of low hardness and low chromium contents (Jang, Iwasaki and Moore, 1988). The purpose of this investigation was to determine the size distribution and the shape of wear debris in a study of the wear rates and wear behaviors of grinding balls. Experimental Materials The grinding ball alloys used in this investigation were: •martensitic stainless steel (MSS; 0.96% C and 16.2% Cr), •high-carbon, low-alloy steel (HCLA; 0.89% C and 0.53% Cr), and •mild steel (MS; 0.22% C and 0.09% Cr). The mineral used in this study was synthetic corundum, because it was on hand and contained no magnetic impurities. Debris A 203- mm (8-in.) diam porcelain mill was used for grinding the corundum. The mill charge consisted of: •1200 g of 12-grit synthetic corundum, •770 mL of 0.05 mole/L Na2SO4 (61% solids), and •125 steel balls of nominally 25-mm (1-in.) diam. To minimize the debris corrosion, nitrogen was introduced into the mill. Grinding with MSS, HCLA-steel or MS balls was conducted for 2 hr at 51 rpm. The grinding time using the MS ball was varied from 0.5 hr to 2 hr in an attempt to study the debris amount and shape as a function of time. The debris was collected with a hand magnet from the ground slurry and separated from the corundum particles using a Davis magnetic tube. After the separation, the debris particles were immediately washed with acetone and then filtered and dried. Debris size analysis Buckbee-Mears 3-in.-diam, micro-mesh sieves and an electromagnetic shaker were used for determining the debris size distribution. In sieving, isopropyl alcohol was used. The debris fraction collected from each sieve was washed with acetone, dried and then weighed on an analytical balance. [ ]

Jan 1, 1993

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By B. A. Filas

Stabilizing fine coal refuse ponds for reclamation at Monterey Coal Company's No. 1 Mine has been difficult. Entrained water in the stored refuse causes liquefaction as reclamation caps are placed, resulting in additional material requirements than originally projected to stabilize the pond surface. Laboratory results indicate that in-place refuse densities may be substantially improved at No. I Mine by converting from a single-point to a managed slurry distribution system. Increased densities result in improved storage efficiency, less entrained moisture and a more stable refuse mass, thereby providing an improved working surface for reclamation and improved post-closure cover stability.

Jan 1, 1993

By Jr. Pickering

Kaolin is mined from extensive sedimentary formations in the eastern Amazon River Basin of Brazil. Production began about 25 years ago from 30 meter thick beds of ultra-fine particle clay of superior viscosity along the Jari River north of the Amazon. Operated by CADAM S.A., capacity now exceeds 750,000 tonnes per year ot high glossing paper coating kaolin product. South of the Amazon on the Capim River are two new operations: Para Pigmentos S.A. and Rio Capim Caulim S.A. The purity , and large coarse plate-shaped particles of these Capim kaolins support production of superior brightness and whiteness paper coating and filling grades. Annual capacities are reported to be 150,000 to 300,000 tonnes each, with expansions planned. Most of Amazon area kaolin production is shipped to western European, Asian, and North American markets.

Jan 1, 1999

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By A. H. Leuschner, P. J. Kruger, J. Kruger

INTRODUCTION This paper deals with some practical aspects of the use and interpretation of dosimetric methods for assessing the exposure of workers to natural uranium. Consideration must be given not only to the scientific value of the method of dosimetry, but also to the practicality of the method in the particular working environment. It is generally accepted (IAEA, 1976) that uranium does not present a hazard during the mining and extraction processes up to the final concentration stage, that is precipitation as ADU or calcining to the oxide. Further processing (e.g. conversion to oxides, fluorides, etc.) is generally associated with the nuclear industry. It is customary for uranium processing facilities to be managed according to industrial norms rather than according to those applied for the purpose of radiation protection. This is mainly because of the large quantity of material to be processed and the fact that uranium is considered to be of a low radiotoxicity. Although ventilation is used to some extent, provision is not made for the same level of protection as would be required in a radiochemical facility. It is typical in such a plant to find that the process itself may be enclosed and ventilated, but the ventilation is inadequate to cope with an accidental release of material. The working environment is poorly ventilated, sometimes only by natural ventilation, and one frequently finds areas with high airborne dust levels, designated as mandatory respirator areas. Protection of personnel is dependent on personal protective equipment. Radiation protection is not of prime concern and personnel are not specifically trained in this subject. It is in this type of environment that acceptable monitoring procedures and personnel dosimetry must be established. The effectiveness and practical application of the dosimetry must also be judged against this working environment. DOSIMETRIC TECHNIQUES The methods available for assessing personnel exposure, whether it be in terms of chemical or radiological hazard, include urinalysis, faecal analysis and [in vivo] monitoring. Faecal analysis does not present itself easily as a method for routine use. Techniques for [in vivo] monitoring have been developed recently and as expensive instrumentation is required, it is not generally available. That leaves urinalysis as a dosimetric technique for routine use, and it is probably for this reason that urinalysis is still widely used. Guidelines for the interpretation of urinalysis results, as originally provided by Neuman (Neuman, 1950), are still used in practice, even though it has become clear that this method has severe limitations as regards the assessment of the dose as a result of the intake of class W or class Y compounds (Alexander, 1974). Typically a level of 300 µg [U/C] urine can serve as an indicator of an acute exposure (above which chemical damage to the kidneys may occur) and a level of 100 µg [U/C ] urine can serve as an indicator for an investigation. Such levels are determined and are used in conjunction with several factors, such as mode of intake (ingestion or inhalation), solubility of compound (D, W or Y), means of intake (acute or chronic), environmental monitoring results and frequency of urine sampling. Since the ICRP concept for internal radiation limitation changed from that of the critical organ, i.e. the single organ of greatest significance under the circumstances, to that of effective dose equivalent, i.e. account being taken of the total risk due to the exposure of all tissue, the maximum permissible organ burden (MPOB) was replaced as secondary dose limit by the annual limit on intake (ALI) (ICRP, 1977). The ALI values are calculated from the committed dose equivalents of the various organs, and are used to determine organ burdens, which are then used to interpret the dosimetric results. Using the ICRP model (ICRP, 1979), a comprehensive calculation was made by Johnson (Johnson, 1980), giving organ burdens and excretion data in terms of intake for acute and chronic exposures for different categories of uranium compounds. The question arises as to what extent the direct measurement of intake can be utilised as a method of dosimetry. This will require a method of personal intake measurement for each individual worker, with both ingestion and inhalation being taken into account. A measurement of

Jan 1, 1981

By Ernest L. Ohie

In 1939 the Geological Society of America published a summary of the geology of the ore deposits of the Mississippi Valley region, This volume, edited by E. S. Bastin, contained contributions from the foremost students of the area which described theregionalgeologic setting of the various deposits as wel as the detailed geology as then known. The various ideas as to the origin of the ores were discussed with the general, though not unanimous, conclusion that the deposits were hydrothermal products, Only those deposits in the immediate Mississippi Valley area were considered without any attempt to introduce evidence from other districts generally accepted as being of the "Mississippi Valley type." Since 1939, much new information has come from extended studies of two of the important districts described in the 1939 report andimportant extensions of the known ore have been found. Likewise, concentrated geologic efforts have been fruitful in severa "Mississippi Valley type" districts - both U. S. andforeign - not treated in the 939 paper. The wealth of new field information on the structural and stratigraphic relations of this interesting ore type, coupled with the results of theoretical and laboratory studies of the past 18 years, makes desirable a review of our present knowledge and interpretation of these important deposits which for many years have yielded over 20 percent of the world's annual production of lead and zinc, together with large amounts of fluorspar and barite. No restatement of the details of the geologic evidence willbe attempted here; the interested student is referred to the papers cited. Slide No. 1 shows the distribution around the world of the deposits under consideration. A principal thesis of my remarks is that there is so much similarity in all these deposits that it seems necessary for all of them to have had a similar mode of origin, whatever that may be. Variations in the shape, size and mineralogy of the orebodies give each district some individuality, but there are enough of the "typical" characteristics present in all cases to make classification in the "Mississippi Valley type" agreeableto most geologists. Thus the overall process giving rise to the ore solutions surely was the same for all in the group. Either they all have igneous affiliations or they all do not. Acknowledgment of this kinship between deposits in the various districts offers many advantages in trying to arrive at a decision as to just what the origin may have been, for the amount of guiding and limiting evidence which must fit into the hypothesis is greatly increased over that available in any one district, To a certain extent this was recognized by the authors of Special Paper 24 in treating all of the immediate Mississippi Valley areas together; by expanding the consideration to include ore deposits of this type all over the world the changes of success, i.e., arriving at the correct answer, are improved several fold. Since most of these districts are quite simple structurally, a number of hypotheses might fit the facts in any one of them, but if the facts to be met can safely be drawn from all the districts, then the explanations which will fit all the data are much less numerous. One purpose of this paper is to call attention to the field facts that have been reported from the .various areas which seem to have an important bearing on the kind of ore fluid that was responsible for the ore and on the way it circulated.

Jan 1, 1958

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By R. Krog, M. Valente, R. Ochsner, W. Marchewka, R. Jensen, R. K. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine for analysis and display on the surface. The U.S. National Institute for Occupational Safety and Health (NIOSH), in collaboration with Signal Peak Energy (SPE), LLC, Bull Mountains No. 1 Mine, operated a TBS during mining of two bleederless, longwall panels. This paper describes the gas analysis data and its interpretation. As verified by the TBS, coal at the SPE mine tends to oxidize slowly. It was known that a reservoir of low-oxygen concentration atmosphere developed about 610 m (2,000 ft) behind the longwall face. A bleederless ventilation system facilitates formation of an inert atmosphere in this longwall gob and decreases the likelihood of spontaneous combustion. Connections of the mine atmosphere to the surface through subsidence cracks could allow airflow into the longwall gob, revive coal oxidation and increase spontaneous combustion risk. The atmospheric composition of the sealed areas was homogeneous, except in the immediate vicinity of suspected ingassing points. The TBS verified that gases within the partially sealed, bleederless longwall gob expanded into the longwall tailgate area when barometric pressure decreased. The concentration of carbon dioxide in the back return airflow at the longwall tailgate was observed to increase by a factor of three and possibly up to 10 times the typical background concentration of 0.5 to 1.0%, depending on the size of the longwall gob and the magnitude of barometric pressure decrease. TBS have the inherent disadvantage of slow response time due to travel time of the gas samples and sequential gas analyses. A TBS or similar continuous monitoring system could be beneficial in detecting and providing warning of potentially hazardous gas concentrations, if the slow response time of the system is always understood.

Jan 1, 2013

By Johann Engelbrecht, Stéfan de Bruyn, Petrus van den Heever

A system for the on-stream X-ray diffractometric determination of mineral phases in slurries was developed in response to the mining industry's need for process control during the beneficiation of industrial minerals. The instrumentation for and results from testwork conducted at a phosphate rock beneficiation plant in Florida are discussed. Results show that the concentrations of the minerals apatite (var. francolite) and quartz can be accurately determined every few minutes, so that adjustments to the flotation circuit can be timeously executed from the control room. The on-stream measurements can ultimately be integrated into an automated plant control strategy. Estimates of savings on reagent and staffing costs, as well as the benefits from consistent grades and greater recoveries, have shown that the investment in such a system could often be recovered in less than a year.

Jan 1, 1999

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By Alan Bye

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimise the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focussed on ore characterisation and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blastability indices as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model however it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables as well as higher plant throughput. Additionally, the initiative has benefited both Brownfield and Greenfield projects on the PPRust operation.

Jan 1, 2005

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By Richard M. Tinlin

Some of the practices of the mining industry that may place an undesirable stress on the groundwater environment are coming under increasing scrutiny from legislators and regulatory agencies. Among these practices are mine dewatering, the use of tailings ponds, land rehabilitation, and technological innovations such as in situ leaching of waste clumps and ore deposits. Pernichele, noting that 24 states have enacted legislation controlling to varying degrees the environmental effects of mining, has emphasized the importance of assessing the potential for damage to groundwater when evaluating, planning, and designing mining projects. 1 Illinois has enacted legislation requiring anyone opening, operating or abandoning a mine site to obtain a permit from the Illinois EPA. The law is one of the first to require regular monitoring and reporting to a control agency. Legislation has also been recently enacted at the national level that will have a significant impact on the mining industry; e. g., the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). The stated objective of this Act is to restore and maintain the chemical, physical and biological integrity of the nation's waters. Specifically, according to Sec. 102(a), the Administrator of the U.S. Environmental Protection Agency (EPA) is required to prepare or develop comprehensive programs for preventing, reducing or eliminating the pollution of the navigable waters and groundwaters and improving the sanitary condition of surface and underground waters. The definition of the terms "pollution" and "pollutant" is of particular significance to those who must comply with PL 92-500. The definitions are quite broad and include most of the adverse water quality effects of man's activities. As defined in Sec. 502(19), "pollution means the man-made or man-induced alteration of the chemical, physical, biological and radiological integrity of water." Within the Act, the list of pollutants includes dredged spoil, solid waste, incineration residue, chemical wastes, radioaetive materials, heat, wrecked or discarded equipment, rock, sand, cellar dirt, and industrial waste discharged into water.

Jan 1, 1973

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991

By M. E. Poad

In 1986, a cooperative effort by the Homestake Mining company, the U.S. Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will be safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modelling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1994

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000