Search Documents

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing bioaxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1997

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By J. M. Stewart

The incidence of heat stroke in the South African gold mining industry is today small (less than 1 in 10 6 shifts worked). Acclimatization and selection procedures have been developed and applied throughout the industry, underground working conditions have, and are being improved, and personnel are to-day made more aware of heat stress and its consequences than ever before. Although these actions have, over the years, brought about a steady reduction in the incidence of heat stroke (see Figure 1) the small incidence of heat stroke which persists indicates that heat stress is still a problem. This realization provides the stimulus for the work presented in this paper, which has as its primary objective the development of reliable heat stress limits for men working in South African gold mines. [ ] In keeping with recent trends3I4 the approach followed in this paper is based on the physical principles of heat transfer. Detailed studies of heat transfer from humans have been undertaken,5-l1 and certain of the results form an important aspect of this Paper -

Jan 1, 1980

By C. M. Lundell, F. S. Kendorski, R. D. Prager

The criteria for the design of the shaft/tunnel system excavation at the Rocky Mountain Project was to provide a stable opening during and after construction to receive the concrete lining and to minimize the disturbance of the surrounding rock mass so that the rock mass resists the displacement of the tunnel mining upon internal pressurization. This paper will summarize the geotechnical design of the shaft, elbow, tunnel, bifurcations, and penstocks

Jan 1, 1986

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By S. Pignolet-Brandom, E. Fregeau-Wu, I. Iwasaki

To recycle steelmaking slags for their iron, manganese and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote sufficient grain growth to achieve liberation. In situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate and the addition of fluorspar promoted grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modeling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1993

By Saverio Agresti, Giuseppe Lunardi, Donato Basta, Roberto Trapasso

"At a distance of 10 years from the first application of the Nazzano Method, the widening under traffic of a tube of an existing motorway tunnel was realized near Ancona, along the A14 Motorway in Italy. This paper describes the works for the enlargement with conventional method of the second tube, very close to that already widened under traffic.This enlargement was realized very fast, taking into account the advantages of some interesting technological improvements of the Final Design proved in the first tube.INTRODUCTION TO THE WIDENING OF EXISTING MOTORWAY TUNNELSThe widening of a twin-bore motorway tunnel usually considers the double option of creating a third bore as an alternative or closure to traffic of one of the two bores with the resulting reduction in the level of service for users.On the contrary, the extension in situ of a road, motorway, railway or underground tunnel in the presence of traffic, made possible by an inspired idea of Prof. Pietro Lunardi, enables the level of service of the infrastructure to be maintained without the need to resort to alternative routes to create new permanent or temporary bores, not always feasible because of the lack of the necessary space.This construction technique, known as the ‘Nazzano Method’, is part of the technologies refined and offered by the ADECO-RS approach to tunnel design and construction (Lunardi P., 2008) which is increasingly used in the world, leading to the industrialisation of tunnelling (meaning respect for the times and costs set out during detailed design) both in conventional and mechanised (through TBM) excavations.The first true experimentation of the ‘Nazzano Method’ was carried out between 2004 and 2007 to enlarge the two-bore ‘Nazzano’ tunnel (Italy, Milan-Rome A1 motorway) in the presence of traffic, widening it to house from two to four lanes in each direction (Lunardi P. et al., 2007). Following the success achieved in this first application, the Nazzano Method was strengthened considering all the possible suggestions arising from the previous experience and then taken up to enlarge the north bore of the ‘Montedomini’ two-bore tunnel (Italy, Bologna-Taranto A14 motorway), in situ and the presence of traffic."

Jan 1, 2016

By David R. Wayman

This paper summarizes environmental compliance and related issues associated with underground construction and tunneling operations, whether new work or rehabilitation. Underground construction and tunneling operations have (in most cases) both an underground and surface component. Since many of the major tunneling projects occur in urban areas, often is areas inhabited for several decades or centuries, environmental problems may already exist in a project area, though that may not yet have been formally recognized. Large projects often attract more than their fair share of regulator attention. This paper addresses the issues with the greatest potential to be encountered by underground constructors, with the emphasis on minimizing contractor liabilities, both in the short- and long-term. Minimizing contractor liability begins with understanding bid documents, contract provisions and necessary means of protection, and carries through project execution by responsible control of hazardous materials, avoidance of media contamination, proper waste disposition, as well as compliance with other environmental requirements.

Jan 1, 1999

By Luis Dr. Sobral

In this study, the removal of zinc, cadmium and copper from an aqueous sulphate solution, derived from the biomass desorption process, was examined by using a reaction system with a three-dimensional high surface area electrode (RNiF). This reaction system was found to be extremely effective in reducing metal concentrations to the ppb range. The effect of cathode potential and flow rate were studied for three different nickel foam porosities. In addition, current- potential curves were recorded, at a rotating vitreous carbon electrode, to deter- mine the possibility of depositing the aforementioned metals separately.

Jan 1, 1998

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By Patrick Linzer

The majority of existing models describing (methane) gas transport within, and liberation from, coal structures treat these as continua wherein two main gas flow modes (diffusive and Darcy permeable) prevail, and use finite difference techniques to generate solutions to the resulting multivariate parabolic partial differential equation(s). Isotropy and homogeneity in the physical and geometric coal structure properties are often assumed, and the existence of fundamental random fluctuations in these proper- ties is not catered for. The model proposed herein does not suffer these inadequacies, and its efficiency is enhanced by the replacement of the diffusion equation by an accurate approximation. Dynamic mining activity, gas contributions made by the geology surrounding the mining seam, goafing of overlying strata and the effects of induced strain are all taken into account.

Jan 1, 1995

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two stage conditioning process was attributed to the amount as well as changes in the nature of the adsorbed collector species upon reconditioning. In this paper, bench scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1988

By R. B. Hoy, Stanley J. LeFond, Unni H. Rowell, K. Reckling, Derek G. Fullerton

In 1989 natural industrial diamonds counted for 55% of the world's natural diamond production. Australia is currently the leading producer (35%). Zaire is the second largest producer (19%). of what is primarily industrial grade rather than gem grade. Botswana (17%) is third, with the former USSR (15%) fourth, and the Republic of South Africa (8%) fifth. Diamonds are also mined in Angola, Namibia, the Ivory Coast, the Central African Republic, Ghana, Tanzania, Guinea, and other African countries. In the Western Hemisphere, Brazil is the principal producer, with some production from Venezuela and Guyana [(Fig. 1)]. A very small output of diamonds is mined today in India, which was the first source of commercial production. In the United States, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a pipe there in 1906. Small scale trial mining has not, however, proved economical. Since diamonds were first discovered more than 2,000 years ago, only about 380 t have been mined. In order to obtain 1 g (5 metric carats) of diamonds, it is necessary to remove and process approximately 25 t of rock. Recovering this small percentage involves a combination of highly developed techniques in mining and extremely sophisticated processes in diamond recovery. END USES Diamonds are used for two unrelated end uses: gem diamonds are jewels of great beauty, while industrial diamonds are essential materials of modem industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamonds in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (1.2 to 1.4 mm). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite", General Electric's Compaxa and Stratapax", and Megadiamond's Megapax" have replaced natural diamonds in turning tools, mining and oil drilling bits, and dressing tool applications. Industrial Diamonds The diamond is by far the most important industrial abrasive. As recently as 50 years ago, consumption of industrial diamonds was less than that of gem diamonds, but since that time, industrial use has grown to a position of great dominance. During the six-year period 1929 to 1934, the material produced for industrial use amounted to about 74% by weight of the world's total output of diamonds. In 1989 the percentage of natural industrial diamonds mined in the world was 55%. When synthetic industrial diamonds are added to the natural industrial diamond figures, this percentage becomes 87% of total world diamond production including gems, near gems, industrial, and synthetic stones. The many uses responsible for these significant increases are dependent on the properties of the diamond, including hardness, cleavage, and parting, optical characteristics, presence of sharp points and edges, and capacity for taking and maintaining a high polish. The utilitarian role of the diamond was confined primarily to lapidary products until the industrial revolution, which created the first demand for diamond as an industrial tool. In 1777, a British inventor and instrument maker, Jesse Ramsden, used a diamond to cut a precision screw for an engine that he had invented. The first authentic description of industrial diamonds being set in a saw was recorded in 1854 by a Frenchman, Durnain. Eight years later a Swiss watchmaker, Jean Leschot, developed the first diamond drill bit for use in a hand operated machine, which was employed to drill blastholes in rock. In 1864, diamond bits were put to their severest test up to that time in the construction of the Mont Cenis Tunnel in the Alps. A few years later a steam-powered diamond drill with a speed of 30 rpm was able to penetrate rock at the modest rate of 0.3 m/hr. As the industrial revolution gained momentum on both sides of the Atlantic, metal replaced wood and machines replaced people. Thus the foundation was laid for precision engineering and the recognition of diamonds as an indispensable tool of industry. The next major demand for industrial diamonds came after World War I with the development of cemented carbide cutting tools. Diamond was found to be the most effective medium for finishing and grinding the new ultrahard metal. This discovery rapidly increased the demand for industrial diamonds. The availability of inexpensive diamond material inspired tremendous research into applications. By 1935, the first successful phenol-resin grinding wheel containing diamond had been marketed. Soon afterward, the metal-bonded and vitrified diamond wheels were produced, and, as the matrices and bonds that held the diamond grit in place began to improve, the popularity of diamond grinding wheels grew. The outbreak of World War II, and the accompanying increase in use of hard-metal tools in the munitions industry, increased the demand for industrial diamonds. Since about 1950, the development of ultrahard ceramics, semi- conductor materials, plastics, and exotic metal alloys has further consolidated the diamond's position as an indispensable tool of industry. Only diamond is hard enough to cut these superhard materials with the precision, speed, and economy that industry demands today. Special machines equipped with industrial diamonds are used to remove bumps from concrete runways and highways and to modify highway surfaces in order to prevent skid accidents. Many skids are caused by hydroplaning, a phenomenon that occurs when the roadway is wet. Tires mount a film of water and virtually lose contact with the road surface. Diamond machines cut neat, narrow

Jan 1, 1994

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977