Search Documents

By Y. Q. Lu

Efficient flotation of fine phosphate minerals from a deslimed waste phosphate stream (-74 microns) has been achieved by both bench-scale flotation and by flotation with a 2-inch air-sparged hydrocyclone (ASH) unit. A sample was collected from the waste phosphate slime stream at the SF Phosphate Limited Operations near Vernal, Utah, for flotation experiments at University of Utah laboratories. The collector used was a mixture of fatty acid, petroleum sulfonate and kerosene. Bench-scale flotation test results show that the minus 15-micron particles have a significant adverse effect on phosphate flotation. When the minus 15-micron material was removed by a classifying hydrocyclone, improved flotation recovery and concentrate grade were realized. A bench-scale flotation recovery of 86 % with a concentrate grade of 16% P2O5 was obtained from classified waste slime (74 x 15 microns) feed material containing 11.3% P2O5 In contrast, a 90% P2O5 recovery was achieved with a concentrate grade of 16-18% P2O5 by single-stage ASH flotation. With a second stage of ASH flotation, a concentrate containing 23% P2O5 was realized at an overall recovery of 75%. These results indicate that the industrial application of ASH flotation technology for phosphate recovery from waste slimes is promising.

Jan 1, 1995

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By Kurt O'Bryan

WaterFlush Technology has recently been implemented at a gold milling operation in the United states. This new technology offers maximum comminution performance bene­fits over today's more common comminution methods. These benefits will be presented via the discussion of performance results from existing installations, and the proj­ected performance gains for circuits sched­uled to begin operation in late 1991.

Jan 1, 1991

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By Y. Tao

The professional status and characteristics of mineral processing were discussed along with the importance of innovative personnel training for mineral processing engineering. Reform ideas and models for the mineral processing engineering education system were suggested to formulate and implement new training program for the mineral processing specialty. It is suggested to strengthen engineering training practices, cultivate the culture of innovation, improve innovative education system and insisting on the combination of teaching with production and scientific research as the important means of training innovative talents for mineral processing engineering.

Jan 1, 2010

By James J. Fallon

I'm glad this meeting is being held in New York. First, because the city is close to my home in New Jersey, only 35 minutes from Times Square ..... if I were to come to Times Square between two and three in the morning. Otherwise it takes two hours. But even more important is the fact that all of you good people from around the country and around the world will enjoy the unique experience of that warm friendly atmosphere in the greater metropolitan area, something that you won't see any place else on the face of the earth. Seriously, the greater metropolitan area has been a large part of my industrial, cultural and spiritual experience. There are many aspects of it which I find disagreeable but on net I would rather live in this area, at least for the time being, than any other area of the United States. As a consultant I find contact with financial institutions, corporate headquarters, information sources and a great many production and research facilities a valuable asset to my activity.

Jan 1, 1985

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By R. W. Smith, A. Raichur, M. Misra, I. A. H. Schneider

The concept of microorganisms as chemical reagents (flocculants, flotation modifiers and flotation collectors) is quite new. Potential uses for microorganisms include their use in place of certain conventional flotation reagents and as flocculating agents in minerals engineering processes. In addition, in some studies micro-organisms have been used to modify mineral surfaces and, thus, the flotation or flocculation of the minerals.

Jan 1, 1995

By Thomas P. Meloy

A brittle solid broken by crushing or impact, results in a mass size distribution curve having a straight line segment when plotted on log-log paper. Depending on the mineral, the slope of this straight line segment ranges from a maximum of one for materials like glass and quartz to values of one half or less. Theoretical derivations of the size distribution, such as the Gaudin-Meloy model, yield a slope of one and only one. When the Gaudin-Meloy model is modified to assume that not all cracks terminate on a preexisting surface, the new model predicts that size distribution slopes, depending on the type of brittle solid, will be less than one. There is a measurable physical parameter that will predict the slope. In addition the model predicts that particles from such a size distributions will have negative corners and peaks - indentations. Moreover the model predicts that particle shape will systematically change with decreasing particle size. Finally, this new physical model of comminution may be experimentally tested.

Jan 1, 1995

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By Robert A. Metz

During the past decade we have witnessed spectacular improvements in productivity of open pit mining equipment. Thousand-horsepower engines, 200-ton trucks and 15-yard electric shovels, which such a short time ago were just dreams on a drawing board, are now realities. More productive equipment and metal shortages have encouraged increased production at existing mines and the development of new larger tonnage operations. Operators and engineers have been able to employ computers and various other types of automation to "stay on top of things". The mine geologist, however, is merely faced with a bigger and more rapidly changing pit to pick in. Keeping geologic information current in these mines presents entirely new problems to mine geological staffs. To obtain adequate geologic information on the developing orebody requires enlargement of the staff to share the work load or revision of methods in keeping with the times. The former has the disadvantage of loss of the comprehensive knowledge of the pit that a chief geologist likes to have, not to mention management's usual lack of enthusiasm for force increases.

Jan 1, 1970

By H. V. S. Tingley, D. Helfant Ghose

"Ten years ago," said a mining industry personnel manager, "we used to wine and dine new mining engineering graduates. Now I can pick and choose among men with 10 years of experience." Comments like that are common throughout the industry today. During the 1970s, the US and Canada did indeed suffer from a severe shortage of mining engineers, especially experienced ones. Moreover, it seemed likely this North American shortage would worsen. Increased production of minerals and coal was pushing demand for mining engineers upwards, and there appeared to be substantial new employment prospects for them in the nascent synfuels industry. The oil majors entering the mining industry were pushing for an increased professionalization of mining management, heralding a trend towards higher intensity in the use of mining engineers. In response to the shortage, mining schools expanded their programs dramatically. By 1982, American schools were churning out more than 600 new mining engineers per year, compared to barely 200 in 1970 (Table 1). The timing of the explosion in the number of mining engineers could not have been worse. The downturn in the economy and the resulting slump in the mining industry coincided almost exactly with peak output of mining engineers. The market for mining engineers shifted from shortage to surplus with startling rapidity. The new crop of engineers, no longer courted by the mining companies, struggled to find any mining jobs. At the same time, experienced mining engineers found themselves thrown into the job market, some for the first time in decades. The current oversupply of mining engineers is assumed to be a temporary phenomenon. As the economy recovers, the demand for mining engineers is expected to pick up at least enough to absorb today's surplus. Not so, according to a recent study by Fenvessy and Schwab, a general management consulting and executive recruiting firm. In 1979, Fenvessy and Schwab was commissioned by a group of major mining companies to conduct a worldwide study of supply and demand for mining engineers to the year 2000*. The study began at the height of the North American shortage. One major objective of the study was "to identify means by which business and educational institutions may cope with and alleviate a future shortage of mining engineering talent." The findings, however, ran directly counter to expectations. The current oversupply will not disappear with economic recovery, the study concluded. In fact, the US and Canada are facing a massive oversupply that will probably last until the end of the century, unless enrollments in schools are reduced. Study Method Fenvessy and Schwab's conclusions are based on supply and demand models for mining engineers that it developed in the course of the study. Specifically, predictions for the supply of mining engineers are based on a survey of the 54 mining schools that account for about 90% of the world's annual output of mining engineering graduates. This survey asked for data on historical and projected number of graduates, obstacles to further expansion, changing trends in the use of mining engineers, and graduate career patterns. Fenvessy and Schwab developed three mining engineering supply scenarios from the survey data. The high case, considered unlikely for most of the industrialized world, is based on a continuation of the 1970's soaring growth rates. The middle case was established from the mining schools' own estimates of future growth in the number of graduating mining engineers. Finally, a "low growth" case for the US and Canada assumed that the number of graduating engineers will remain at current levels. Mining engineering demand was forecast using a complex model based on the demand for 50 major minerals. Formulas were

Jan 9, 1983

By B. M. Ghadiali, J. B. Putnam, T. P. Smirnoff, M. A. Elioff, P. F. Ryan

Geotechnical investigations for the Mid-City Extension of the Los Angeles Metro revealed high concentrations of toxic hydrogen sulfide (H2S) gas as well as methane. Testing techniques employed to determine the extent of gasses, and to identify potential treatment measures, included gas sampling with cone penetrometers and soil-gas extraction with air injection testing. A gas reservoir model was developed to predict inflows into excavations. Other studies included a hazard evaluation and a general data search for other H2S occurrences and geologic conditions that could facilitate the accumulation of H2S. The paper describes the investigations and proposed design and construction alternatives.

Jan 1, 1995