Search Documents

By B. A. Ferguson, P. W. MacMillan

INTRODUCTION Jack Spalding in Deep Mining, Chapter 3, states: "In deep mining, to start stoping an orebody without a definite plan of operations covering the whole extraction from beginning to end is to invite serious trouble. Any stoping without plan is bound to leave, toward the end, a number of pillars, remnants, or promontories, which, as they are reduced in size, are liable to fail and cause a general collapse. The object of stope planning is so to mine an orebody that at no stage in the operation is a remnant left. Definition: `When a block of ore is stoped in such a way that eventually a small piece is left entirely surrounded by stoping, that piece is termed an island remnant.' The design of and adherence to a plan of stoping is of greater importance in preventing rock bursts than the type of ground control adopted." This, of course, is just an example of the old axiom that an ounce of prevention is worth a pound of cure. And in this context, mining does not have to be very deep before poor ground conditions, made worse by lack of good planning, force a mining company to resort to more expensive methods of ore recovery. At all times when rock pressures become excessive, stoping plans must be devised to avoid the creation of pillars or promontories. This is most readily recognized when mining deep narrow ore veins by open methods. It would be a little more general to say that stoping systems should seek to avoid or minimize localized concentrations of rock stress. Ore bodies, and particularly those at Falcon¬bridge, can reach large widths and leaving pillars for extraction at a later time cannot be avoided. However, good planning can reduce the effect of factors which create bad ground conditions. The necessary ingredients of planning are time and information: time to formulate and revise ideas; information, gained in exploration and early development, to provide the fullest knowledge of the ore body. In this way, plans become meaningful. It must always be kept in mind that the long-term results of good planning often require decisions not compatible with reaching earliest full production. PLANNING FOR DEEP MINING At Falconbridge Nickel Mines ore bodies presently being found and prepared for production lie at depths in excess of 610 m (2000 ft) below surface. Current un¬derground exploration is being directed towards favor¬able locations below 914.4 and 1219.2-m (3000 and 4000-ft) depths, at most mines. The Onaping Deep ore body has been traced to a depth of 1508.8 m (4950 ft) and at Falconbridge mine the ore body is under develop¬ment below the 5000 level. Planning for more efficient ground control has therefore become an important con¬sideration of future mining. HYDRAULIC BACK FILLING AND CUT-AND-FILL STOPING The advent of hydraulic back filling has led to the increasing use of flat-back cut-and-fill stoping methods during the last ten years, until it has probably become the commonest method of mining deep ore deposits in Canada. These methods account for almost all the pro¬duction from Falconbridge Mines at this time. The ad¬vantages claimed are: safety-a minimum of open ground; very little supplementary ground support (except rockbolted backs and walls); greater selectivity and flexibility in extraction (horizontal extension of the vein, high grade ore stringers going out into the walls); and high productivity and increased mechanization in larger ore widths. There is some difference of opinion as to whether hydraulic classified tailing back fill provides any great resistance to initial closure of the stope walls. The evi¬dence available suggests that it does not. Addition of portland cement to the back fill just prior to placement has produced a material having the properties of a weak concrete. It is confidently expected that this material will assist greatly in the efficient mining of pillars and generally in giving increased ground support to oppose closure. PRINCIPLES OF STOPE PLANNING BY LONGITUDINAL FLAT-BACK CUT-AND-FILL Again quoting from Spalding: "The practice of con¬trolling output by stopping and starting stopes is bad¬stopes once started should proceed without interruption, and control must therefore be obtained by altering the rate of stoping. It is therefore necessary that faces should normally advance at a medium rate which can be boosted, if required, to give temporarily a greater output. Modern high productivity stoping methods, however, generally aim to achieve and maintain the maximum output possible from a stope. Control of tonnage and grade, therefore, becomes a more complex problem requiring very careful scheduling and organiza¬tion. With the basic method of flat-back overhand stoping using hydraulic fill, it is not usually possible to mine in such a way as to avoid creating pillars." Consider an ore body as illustrated in Fig. 1. It is 274.3 m (900 ft) high by 228.6 m (750 ft) long on strike and averages 4.6 m (15 ft) in ore width. It rep¬resents approximately 907 000 t (1,000,000 st). The ore body could be mined by advancing one long single face through all the levels from bottom to top. A total face length of 228.6 m (750 ft) would accommo¬date five 45.7-m (150-ft) stopes. See Fig. la. Each of these stopes would produce approximately 1814 t/m (2000 stpm) and the ore body would require a period of ten years for complete extraction. A possible im¬provement to this scheme might be to stagger the indi¬vidual stope faces. See Fig. 1b. Problems of hanging wall failure can be reduced by this arrangement. From the point of view of reducing travelway maintenance, it is good practice to employ a stoping system of retreat. Stopes farthest from the shaft are mined first so that on completion, haulage drifts below can be aban

Jan 1, 1982

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982

By Emily Dieckman, Claire Kincaid

"When most people think “miner,” they picture an older white man in a dusty shirt and suspenders. He’s holding a gas lamp and a pickaxe, peering at the walls of a dimly lit cavern. This image, while steeped in heritage, is no longer representative of what mining is: a global, increasingly diverse industry.It’s an industry made up of individuals like Zambian-born Chushi Mwewa, PE, president of Southlands Engineering, LLC in the United States and managing director of Southlands Engineering Limited in Zambia; Navajo tribe member Peter Denetclaw, manager of environmental programs and Navajo relations at Freeport-McMoRan; and Chinese and Jewish Alyssa Hom, a project engineer at McCarthy Building Companies.According to the Austrian Federal Ministry of Science, Research and Economics, 168 out of the world’s 195 recognized countries have some mining or mineral resources activity, and the mining industry directly employs more than 25 million people across the globe.However, according to McKinsey & Company’s 2017 “Women in the Workplace” study, white males hold 67 percent of C-Suite positions and 70 percent of senior vice president positions in the corporate world, and mining is no different. This uniformity among leadership has been tied to lower levels of employee engagement, innovation and business growth. The bottom line is this: Diversity is good for business. The question industry leaders must now ask themselves is not “Will we promote diversity?” but “How will we promote diversity efficiently and permanently?”More than 80 industry professionals, consultants and students gathered to discuss this question and share stories at the “Developing Diversity in Mining” workshop organized by the University of Arizona’s Lowell Institute for Mineral Resources (IMR), held during the 2017 SME Arizona Conference in December 2017.Brad Ross, co-director of the IMR and one of the facilitators of the workshop, said he felt diversity was important to discuss because he has witnessed its benefits throughout his career in the mining industry.“By creating a team of people with different experiences and perspectives, a company is better equipped to see the big picture and to creatively tackle problems,” he said. Speakers from industry and academia,including Mwewa, Denetclaw and Hom discussed the challenges surrounding achieving diversity and inclusion as well as the roles and responsibilities of different stakeholders."

Jan 2, 2018

By L. M. English

A basic model has been developed to help assess methane control needs for longwall mining of coal in gassy areas. Rather than depending upon reservoir and rock mechanic theory, it uses an empirically-determined gas emission rate as an input and operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance, and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid the determination of the number, size, and location of vertical wells or other methane control applications that are needed for gob gas control.

Jan 1, 1998

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

As orebodies being mined globally are of ever-decreasing grades, the focus on the concentration process has moved increasingly to the challenges faced in management of the gangue minerals. This is especially so in the flotation of platinum group minerals (PGMs), where head grades are typically in the region of 4–7 g/t. Hence, in PGM operations, a typical recovery of about 80 percent requires depressing about 85 percent of the gangue minerals. In a flotation cell the main control parameters are reagent type and dosage, froth depth and air addition rate. This paper reviews research projects carried out over an extended period aimed at optimizing the depression of gangue minerals: both those that are naturally floatable and those, such as chromite, that are entrained.  This has involved comparing the two major depressants used in the industry — guar and carboxymethylcellulose (CMC) — in the depression of the relevant gangue minerals, as well as investigating their consequent effect on the behavior of the froth phase. Because most PGM flotation plants treat the ore as if all the PGMs are associated with sulfides, copper sulfate is widely used as an activator, but this can also lead to inadvertent activation of gangue minerals. Finally, chromite levels must be kept below 3–5 percent to avoid any negative effects on smelter performance, and thus it is important to reduce chromite recovery which mainly occurs due to entrainment through, for example, froth depth control.   

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By Wendell H. Nielson

Flotation processes contain disturbances which make material balance closures difficult to achieve. Lack of closure also arises from instrument errors. A portion of these problems can be overcome by proper equipment selection; the primary measurement installation and methods of initial data filtering are discussed below. The problem of data adjustment has been considered before (2). The technique described here is essentially that of Ripps (2). The technique was expanded to include linearization of non-linear material balance equations. An additional large error detection portion was also added to Ripp's formulation. Ripp's technique is based on a Lagrange-Multiplier optimization method. The Lagrange-Multiplier technique is generally applied when there are equality constraints on the variables. Steady-state material balance equations fit in this category. The basic Lagrange-Multiplier method is described. It is followed by a description of the modified material balance data adjustment technique. An example is presented to illustrate the use of this method.

Jan 1, 1970

The most common method used for cleaning the fine fraction in today's coal preparation plants is froth flotation. Past research and practice has found that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, its efficiency decreases sharply as the concentration of middling particles increases due to the flotation of high-ash particles having a small amount of hydrophobic coal present at the coal surface. Since gravity-based processes are much more efficient at treating middlings, the application of centrifugal washing for fine coal cleaning has been studied with an emphasis on the primary cleaning of fine circuit feed. Results will be shown from a parametric study using a Falcon centrifugal concentrator which reveals that the separation performance is a function of particle size, bowl geometry, feed solids content, and feed rate.

Jan 1, 1994

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By G. Blackwell

In the 1980's the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990's, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By Michael J. Mankosa

Carpco has recently evaluated the use of various mineral processing techniques for secondary materials recovery. These applications include recycled foundry sands, plastics and secondary metals. This paper describes different recycling applications and the associated separation solutions. Results from extensive laboratory-and pilot-scale test work in each area are discussed. Industrial installations resulting from this test work will be presented. A detailed description of an industrial installation patented by Carpco for the recovery of plastic and metallics from current waste by-products is presented.

Jan 1, 1997

By Colin C. Brooks

The Ok Tedi gold/copper deposit of almost 800 million tonnes was found in I968 because at that time technology had just developed sufficiently to enable exploration of such an area, world markets and prices for copper encouraged exploration for large deposits of low grade ore, Papua New Guinea law encouraged exploration by groups with men, money, management and expertise necessary for successful prosecution of such a search and such groups were already operating in the country.

Jan 1, 1990

By Ademar Lopes, Victor Silva, Heitor Silva, Gustavo Usero, Roberto Rolo, Lucas Pereira, Gabriel Moreira, João Lague, Arthur Endlein, Matheus Feitosa

Grade control models are supposed to provide a higher resolution than long-term or interim models. However, available grids from diamond or reverse circulation drilling do not provide that required resolution. In this study, a geostatistical workflow is proposed to integrate available grade data from production blastholes with its operational parameters taken when drilling downhole. The step of geological logging can be replaced by machine learning models for classifying blastholes into lithologies and hardness classes. Next, indicator and ordinary kriging use the classified blastholes and previous data for estimating the model domains and the grades within each one. The workflow is applied in a world class iron ore mine in Brazil.

Jun 25, 2023

By C. R. Peterson

A cutter vibration monitoring system is described which would map seam strata non-uniformities to permit guidance within the seam. An extremely simple and rugged transducer is used which is compatible with conventional cutters and cutter replacement practices, and believed to be suited to the mining environment. Laboratory tests show that the system can detect bedding planes in otherwise homogeneous material. A data display system which would employ the human operator's natural pattern recognition skill and judgement will be developed, Intended for remote control applications in general, the system is of direct interest for today's continuous excavators in coal or in any other machine excavated bedded deposit.

Jan 1, 1985

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995