Search Documents

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By Frank J. Hirner

Economic open-pit and surface mining often call for ever increasing volumes of lower grade materials. So it is important, often critical, to develop precise expense and production estimates for the large electric mining shovels now in use. An electric shovel's basic application is to "shovel up" material, starting at ground level with the dipper moving up into a working face or bank. It's impractical to dig below ground level with a shovel, except briefly or in unusual circumstances. The shovel working face is "the bank," whether the material is dug from natural bed or blasted. The shovel's digging attachment, the boom and dipper handle, is built in standard and long range configurations. A standard digging attachment is normally used for loading into haulage equipment. The long range attachment is normally used for side or hack casting to a spoil pile. It is also used fir loading into haulage equipment placed above shovel ground level, as in some coal loading applications. Shovel clipper size and hauler capacity should he matched so that a hauler can he loaded in three to four shovel work cycles. Five cycles is usually the limit of good practice. If fewer than three cycles are required, the hauler is too small. More than five cycles indicates possible excess harder waiting time for loading, or shovel waiting time for too few haulers. Full dipper loads, including the last dipper or ''pass, " are essential for economical shovel and hauler match. Consistent need for a final partly full dipper to fill the hauler shows an improper match between the two.

Feb 1, 1981

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By William Mayrsohn

INTRODUCTION The net smelter return (NSR) calculations made on various smelter-refiner alternatives, is usually done by taking the gross metal value less metal deductions, smelter-refiner charges and transportation-insurance costs. An important further step in the calculations is the financial charges imputed by refining time, transportation delays, to the time gold is returned (if tolled) or paid for if bought by the refiner. Metal that is priced in advance of payment also requires a forward premium that the mine may or may not be getting. This is a hidden cost that is often omitted from the calculations. Segmentation of each of the above costs are vital to see where improvements can be made through negotiations, better choice of metal pricing or transportation alternatives. BASIC NSR CALCULATIONS SMELTER-REFINER CHARGES Payable Metals - Treatment Refining Charges: Since these can vary from one smelter to another, the effect of a $25 per ounce price increase/decrease should be calculated and kept in mind. This effect is compared to differences in refining/treatment charge and a total smelter/refiner cost on a cost per ounce of dore, gold, or a dry ton of concentrate. Transportation - Insurance: Research has to be done on transportation alternatives perhaps with some assistance from the smelters, railroads or trucking companies. For dore, the U.S. postal service is viable and inexpensive. For railroads, deal with the regional office ie., B&N El Paso, if production warrants regular bulk shipments. Spot rates tend to be higher. A small mine producing concentrates usually goes to the nearest smelter due to extremely high transportation costs. Here is where a refiner can help. Insurance-Quotes for rates on dore/ concentrates are easily obtainable, but the mine has to shop for the best rates. Your insurance broker is the best source of this information. Differences between Mine and Smelter/Refiners Metal losses can be caused by the following: - Concentrate dry weight differences caused by moisture determination or faulty scales (often at the mine). - Sample bias by poor preparation practices on either side ie., grinding of the sample removing gold; or a poorly mixed concentrate. Dore bullion has no such difficulties.

Jan 1, 1987

By J. Gonzales

For this paper, blending is conceived as a linear process that takes a proportion from one stockpile or location and mixes it with another proportion from another stockpile or location, with the aim of obtaining a set of attributes in the final combination that satisfies a given quality standard. A blending class is the combination of ore attributes and grade limits that should be stockpiled in order to achieve the target quality for the process Plant. Current literature considers the number of blending classes in the Open Pit Scheduling Problem as fixed; however, this paper shows how to define specific blending classes for a given deposit so that the schedule can be solved with Sequential Linear Programming. Finally, a practical application in a Peruvian copper mine is shown, involving four ore attributes: alteration code, arsenic, oxide content and copper grade. INTRODUCTION In copper ore deposits, blending for quality has not been a typical issue as it was for coal and iron ore; however, current copper deposits in the world are becoming geologically and chemically more complex than in the past and is not uncommon to have quality standards involving up to four attributes, introducing an additional complexity to the mine scheduling process [1]. In order to solve the Open Pit Scheduling Problem with multiple ore quality constraints, two assumptions are necessary [2]: - Grade constraints are defined only by specifying an upper and lower limit; - Ore attributes in stockpiles are pre-determined, i.e., the upper and/or lower grade limits defining each stockpile are already known at the time of setting the schedule. Assuming each ore attribute is classified as high, medium or low, and there are four attributes to be controlled in the target ore quality, the number of possible blending classes would be 3^4 = 81. This number is impractical to manage in Operations, and increases the complexity at the time of running the schedule; therefore, a more efficient way of classifying ore is required. Note that in practice, one blending class can be split into more than one stockpile location due to physical capacity constraints. Therefore, the number of stockpiles could even be more than 81. BLENDING CLASSES DETERMINATION For a given set of ore grades with lower and upper limits to be achieved, one has to find all feasible ore classes such that when blended, their grades will lie within those limits.

Jan 1, 2019

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By N. P. Reddy, Y. J. Wang

This paper describes an experimental setup for multiple fan ventilation systems at the ventilation laboratory of the West Virginia University Department of Mining Engineering. Housed in a 30-ft x 70 -ft room, the experimental setup consists of three 18-in., variable-speed, axial flow fans; an 18-in. -diam, fiberglass tubing; associated fittings for arranging networks; and a picot-tube measuring and data-acquisition system. The fiberglass tubing and fans can be organized into non-planar networks of two or three fans. The setup is mainly designed for studying the characteristic curves, operating points and fan stall for multiple fan ventilation systems.

Jan 1, 1993

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for the removal of copper from heap-leach solutions without mobile organic phases are a current mining industry need. To satisfy this need, a selective, high-capacity, durable solid material is required. The Idaho National Engineering and Environmental Laboratory (INEEL) developed a set of materials based on current solvent-extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, the author's strategy anchors the chelators to a nonpolymeric solid substrate through the use of a custom-designed linker molecule. The fundamental synthetic routes to these materials have already been established, and attachment to the solid surfaces have been achieved in an efficient manner. The author's continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper-capturing capabilities.

Jan 1, 2003

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By Jacques L. Mauboussin

The EUROPEAN ORGANIZATION for NUCLEAR RESEARCH (CERN) has undertaken the construction of a LARGE ELECTRON POSITRON COLLIDER (LEP), near GENEVA (Switzerland). The facility includes the main 27 km long tunnelled ring, 18 shafts, 20 experimental caverns and many auxiliary galleries. Roughly 800 000 cu.m were excavated in the molasse at 50-140 m depths, using roadheaders for caverns and auxiliary tunnels and 3 WIRTH, 4.5 m diameter, fullface TBMs for the main circular tunnel. Each TBM performs 25-30 m/day. Provisory lining behind them uses either precast concrete elements or shotcrete. Works a e being carried out by a joint-venture of European contractors led by FOUGEROLLE (France).

Jan 1, 1987

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By A. Perelli Cippo, R. Granata, D. A. Bruce

During the last few years, significant advances continue to have been made in aspects of grouting technologies used for ground treatment in advance of tunnelling. In permeation grouting, fundamental researches have continued into improving the penetrability characteristics of cement-based grouts. The twin advantages of field regrinding normal grouts to reduce cement particle sizes, and incorporating special additives into stable grouts, are now being systematically exploited in major soft ground tunnelling projects in Europe. The methodologies of jet grouting continue to be developed with special attention being paid to qa/qc issues, reducing unit production costs, and improving predictive capabilities for subsequent settlements.

Jan 1, 1993

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Erkan Bozkurtoglu

The most important difference between weathering and alteration, which are the definition of the change in rocks that occur with the help of physical and chemical effects, is a new product is formed as a result of alteration. Although atmospherical conditions are the most important factor during rock change, geothermal fields play a large role in the developing of alteration phenomenon. Because every geothermal system shows different characteristics including the chemistry of geothermal fluids and their potential applications, alteration on the field is important for the studies to find geothermal energy sources and to obtain the thermal fluids. The development of weathering and alteration which is the mark of interaction , between the physical and chemical properties of geothermal fluids and gases with the reservoir and wall rock, gives out important data about the hydrogeology, hydrology, reservoir conditions and characteristics of reservoir rocks of the geothermal field. Therefore defining the development of weathering and alteration phenomenon in a geothermal field and modeling the change in rocks, is very important for the benefication of the geothermal field economically. In this study 70 km2 that reside between Kösedere plains, Uzunburun, Çamtepe, Centirler villages in Çanakkale - Ayvacik - Tuzla geothermal field were studied and subsurface travel of saline thermal fluids and their interaction with the rocks and development of weathering and alteration phenomenon in the field were investigated. For this purpose geological mapping of the field were done and observations and measurements as well as rock sampling were carried in locations more than 220. As the result of petrographical investigations of rock samples development of weathering and alteration phenomenon were defined and 16 rock samples out of 220 that represent the field in general were chosen to be chemically analized and after that geochemical comments on the Tuzla geothermal field were made. Also hydrothermal alteration zones that are located in Tuzla Tepe, on which weathering and alteration phenomenon is observed as widespread and thermal water discharge locations in the near perimeter of Tuzla Tepe were mapped and from these data rock change in Tuzla geothermal field were modeled.

Jan 1, 2005

By Deepak Malhotra

Western technology is considered a panacea for all ills in developing countries. Is that really the case? Are inventors of new technology overselling? What are the expectations of the receiving party? The author offers his views on these questions and proposes a process for systematic transfer of technology while minimizing surprises on the part of the seller and the receiver.

Jan 1, 2001

By S. J. Aparo

Phosphate mining and beneficiation in the State of Florida are presently being carried on by 12 different mining companies with a total of 21 mining and flotation plant locations. Their combined production of both washer rock and flotation concentrate was approximately 28,000,000 long tons in 1968. This accounted for 70-72% of the total U. S. production and close to 30% of the world's output of this mineral. From this extensive activity in the Florida phosphate field, one basic flow sheet for beneficiation of the ore has developed over the years as the most commonly employed. In fact, all of these plants with the exception of two beneficiate Florida pebble phosphate using a basic operation as illustrated in Figure I. The two plants which differ from this general approach are not using raw matrix as feed. In one instance, +14 mesh pebble is ground in a rod mill to release free silica which is subsequently removed in a cationic froth flotation circuit using an amine acetate blend and kerosene. This technique generally results in a 4-7 BPL unit upgrading of the feed pebble. The other exception to the standard flow sheet illustrated in Figure I is an operation which is beneficiating tailing piles. In this case, the material is first subjected to cationic froth flotation in order to upgrade the feed to a point comparable to normal matrix. Thereafter, after, the phosphate is floated in an anionic rougher circuit followed by cationic flotation of the silica in a cleaner circuit.

Jan 1, 1969

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Flavio Moreira Ferreira

In mining industry, one of the simplest methods to smooth the standard deviation of a given ore controlled property is to build longitudinal blending piles. The effect of homogeneization is obtained due to the fact that an entire cross-section of the pile is reclaimed at each time. The variance of the pile output is the sum of the internal cross-section slice variance plus the reclaimed slice variance. While the first term is a tipical short-term parameter and is absorbed by the process, the second one may be or may not be absorbed. The goal of designing blending piles is to minimize the reclaimed slice variance. Conditional Simulation as described in this paper, is an alternative method to do it. It is devised to design longitudinal blending piles, taking into consideration economical, geometrical and statistical parameters of the ore to be blended, in order to estimate the resulting effect. It presents advantages in relation to other methods for its adaptability and flexibility in simulating pile performances.

Jan 1, 1992