Search Documents

By MYRIAM FRANCOEUR, JOHN R.R. BOWLING, ADAM MCFADDEN

As duct-fan systems push the envelope of power, length and cost, their design calls for a more comprehensive technoeconomic analysis to ensure they deliver the expected results without failure and cost overrun. This work explores the numerous factors to include in the design of an extensive (semi-)rigid duct-fan system. Besides delivering a given airflow, the system must satisfy component limitations and power constraints during its lifetime. We evaluate the assumptions underlying the positioning of in-line booster fans in a long gapless duct-fan system and propose a strategy for specifying the location and blade pitch of successive booster fans to prevent system failure due to a partial vacuum.

Oct 1, 2022

By Jean-Michel Rendu

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual fitting of the model is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. A number of interactive methods are described, which are adapted to the modeling of semivariograms in one-, two-, or three-dimensional environments.

Jan 1, 1982

By Courtney Black, Paul F. Ziemkiewicz, Eberhard Werner, Matthew Daly, Joseph J. Donovan, Jeff Frazier

Injection of alkaline waste-lime slurry was performed at a West Virginia surface coal mine site, to attempt neutralization of acid springs by an alkaline recharge method. Deep trenching (>5 m) using an excavator yielded the most effective injection into the aquifer. Water from two springs, 90 m from the deep trench, showed 70%-80% reduction in acidity in response to injection. Neutralization persisted >170 days after treatment, with pH between 5.1-5.7 and metal acidity from 25-60 mg/L. A minor fraction of lime introduced was consumed. The sustained neutralization is attributed to reaction of acid water with subsurface lime, entrained below the wafer table by macropore infiltration. Characteristics of groundwater transport are critical in determining recharge structure location.

Jan 1, 2000

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee's Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today's competitive markets.

Jan 1, 1984

By S. Miller, A. Krasner, M. Sizintsev, S. Schafrik, H. -P. Chiu, J. Sottile, A. Rajvanshi, Z. Agioutantis

In recent years, a great deal of effort has been put into automating mining equipment with the goal of improving worker health and safety and increasing mine productivity. Significant progress has been made in automating mining equipment such as load-haul-dumps and drills in underground environments where global positioning systems are unavailable. This paper addresses automating the task of positioning the shuttle-car (SC) under the continuous-miner (CM) coaldischarge conveyor during cutting and loading operations. A stereo depth camera is mounted on the SC. Machine learning based algorithms are applied on the camera’s output to identify the CM discharge conveyor and segment the scene into various regions such as roof, ribs, and personnel. This information is used to plan the shuttle car path to the CM discharge conveyor. The approach currently uses a 1/6th scale continuous miner and shuttle car in an appropriately scaled mock mine

Mar 2, 2022

By Jouko Suominen

The basic development of various mining equipment has been strongly influenced by two objectives; improving economic results and safety aspects. Both of these factors contribute to increased requirements of mechanization and automation in different parts of mining processes. When we are limiting the discussion the crushing circuits, automation has two dimensions, one being the component automation, or intelligence, the other being automation of complete processes. Both of these subjects are closely tied up, the former being a condition for the latter. The key technologies of crushing automation are transducers, programmable logics and computer software. Also equipment technology continually faces new challenges, which result even in totally new product families. One example of this kind of development area the track-mounted, integrated crushing systems, where design criteria have been simple control, unmanned operation, and flexibility in changing requirements. This crushing system, or philosophy, offers excellent possibilities for new concepts in various underground and open pit applications, connected with automatic process control. Following presentation is a summary of aspects, of haw a crusher manufac¬turer sees the development of automa¬tion as an integral part of equipment technology and development.

Jan 1, 1989

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By J. R. Johnson, C. G. Stewart, D. K. Myers

INTRODUCTION Radon-222 is an inert, radioactive gas formed by the radioactive decay of radium-226, a long-lived member of the uranium-238 decay chain. Radium is present in varying amounts in virtually all soils and, on the average, about 36,000 pCi (1330 Bq) of radon per square meter of soil diffuse into the atmosphere each day (UN 1977). Radon decays with a half-life of 3.6 days through four short-lived daughters to lead210 and it is these short-lived daughters[ [Ra A, (218Po, t, = 3.0 min) , Ra B, (214 Pb, t;, = 27 min), Ra C, (214Bi, t] = 20 min) and Ra C1 (214Po, t] = 2.5 x 10-6 min)] ]which cause the major health hazard associated with radon (Bale 1951). Atoms of these daughters, either unattached or attached to the ever-present particles in air, are deposited on the surfaces of the respiratory tract; alpha particles emitted in their decay can result in large doses to the cells of the bronchial epithelium lining the respiratory tract. These daughters will be present in air in varying relative concentrations depending on the "age" of the air (time since radon emanated into it) and on the amount of mixing of radon and radon daughter contaminated air with clean air. [The practical unit developed to quantify the amount of radon daughters in air is the Working Level (WL). This unit was historically related to the equilibrium concentration of 100 pCi (3.7 Bq) of the short-lived daughters of radon in one liter of air (cf. Holaday 1969) and is defined as any mixture of the short-lived daughters in a liter of air that have a-potential alpha energy of 1.3 x 105 Mev (2.08 x 10-5J) in their decay to lead-210. The working level month (WLM) was developed along with the WL, and was defined as an exposure to one WL for a working month (170 h). This is equivalent to 2.2 x 107 MeV•h•L-1 (3.54 x 10-3 J.h.m-3). If the average breathing rate is taken as 1.2 m3.h•1 (ICRP 1975), then one WLM is equivalent to inhalation of 4.24 mJ of potential alpha energy.] It is now generally agreed that the inhalation of radon daughters is the major potential radiation hazard in uranium mining, and contributes a substantial fraction to the natural radiation exposure of the general population due to the accumulation of radon and radon daughters from natural sources in buildings. Radon daughter concentrations in modern mines are controlled by ventilation, and by blocking off old working areas (cf. Simpson, 1959). However, before the hazard from radon daughters was recognized, considerably higher concentrations of radon daughters were present in some uranium and non-uranium mines. These high radon daughter concentrations resulted in an increase in lung cancers in the mining population, and it is these results that are our main source of information on the risk of inhaling radon daughters. HISTORICAL REVIEW Many excellent reviews of the history of understanding the health effects of inhalation of radon daughters are available (see, for example, Hueper 1942, Lorenz 1944, Sikl 1950, Stewart 1964, Holaday 1969, Lundin 1971, Cross 1979) but a brief summary of some of the highlights in this area may be of interest. [a] 1556: Agricola describes an unusual and fatal chest disease occurring among underground miners in the region of Schneeberg and Joachimsthal (Jachymov) in the Erz mountains in Central Europe. (It is of some historical interest to note that Agricola's book was translated from Latin into English by a mining engineer and his wife; the engineer later became President of the U.S.A.) [b] 1879: Haerting and Hesse indicated that the majority of deaths among Schneeberg miners were due to lung cancer; the lung cancers in these miners (who were incidentally not cigarette smokers) were observed twenty to fifty years after they began working in the mines. [c] 1896: Discovery of natural radioactivity by Becquerel, followed by discovery of radon by Dorn in 1900. [d] 1924: Ludewig and Lorenser report high concentrations (400 - 15000 pCi or 15 - 570 Bq per liter) of radon in the air in the Schneeberg mines and suggest that radon could be responsible for the high rate of lung cancer among miners. However, the reason why radon should cause lung cancer specifically was still not really understood up to twenty years later (Lorenz 1944). High concentrations of radon in the air in the Joachimsthal mines were reported by Behounek in 1927 and a high incidence of lung cancer among Joachimsthal miners (similar to that among miners at Schneeberg, which is only some 30 km distant but in a different political district) was noted at about the same time (Sikl 1930; cf. Sikl 1950). It is estimated that about half of the Joachimsthal miners died from lung cancer and about half from silicosis and tuberculosis (Sikl 1950). [e] 1930's and 1940's: Radioactive ores are deliberately mined in the U.S.A., Canada and other countries primarily as a source of radium for medical purposes and for luminescent dials; other radioactive ores are mined as a source of several non-radioactive minerals, while extensive uranium mining did not begin until the late 1940's. [f] 1940: Based on crude epidemiology and dose calculations, Evans and Goodman propose 10 pCi L-1 as a maximum permissible concentration of radon in continued human exposure. This is the first known recommended maximum permissible concentration for radon. This recommendation was adopted by the U.S. National Bureau of Standards in 1941 and reconfirmed in 1953. [g] 1945: Mitchell identifies the short-lived daughters in radon as a likely cause of the increased lung cancers in the Schneeberg-Joachimsthal miners

Jan 1, 1981

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof bolt reinforcement of the roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening with variables such as opening width-height ratio, number of bolts installed, number/location of bedding planes, in-situ stresses, etc. The most critical areas are identified and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1989

By Ray Soper

Important progress has been made in developing the K-Process as an alternative to cyanide as a method of recovering gold from ores and other materials.

Jan 1, 1998

By R. L. Schmidt, Williamson. T. N.

INTRODUCTION This paper describes one of several research projects funded by the Advanced Research Projects Agency to extend the technology of rapid underground excavation. This study and field research effort are to investigate alternative means to determine rock and geological conditions in advance of a tunnel boring machine (TBM). Approximately 1 year of a planned 3-year program has resulted in the definition of three candidate drill systems. Hardware has been assembled to field test these candidates and testing has begun. The 3-year objective is to develop a single optimum prototype drill and test it in an active TBM operation. ACKNOWLEDGMENT This research was supported by the Advanced Research Projects Agency (ARPA) of the Department of Defense and was monitored by the Bureau of Mines under Contract No. H0210037. The authors and sponsoring agencies are indebted to the quarry operators in California, Virginia, and West Virginia who offered assistance including access to their properties.

Jan 1, 1997

By C. J. Milam

Oil shale may not produce the same excitement of the gold rush days, but presently there is an "oil shale fever" among mining men. Such exotic equipment as 800-ton haul units, 75 ft. boring machines, and huge fully automatic multi-purpose jumbo drill units are only a few of the topics of conversation in the oil shale groups. I am dreaming, perhaps, but this type of exotic thinking will exuberate the advancement in mining technology and will only be tempered by the practicality and the availability of today's equipment.

Jan 1, 1975

By Edward C. Dowling

The advance of science and technology influences the modern economy in countless ways. Older industries must adapt to changes in the marketplace, while new industries are born by applying new technology to meet consumer needs. In light of declining head grades and increased unit costs in the US minerals industry, new technological developments in the production environment are paramount to maintaining a competitive footing in the international marketplace. Micro-engineering research provides the transition between the knowledge base and the application of new technology on the production level. Economic considerations The primary goal of technical development in the production environment is to reduce unit operating costs. Simply stated, this is accomplished by improving operating efficiencies and productivities on the production level. The goal of micro-engineering research in the production environment is to evaluate promising technologies and develop the criteria necessary to apply them in operations. As such, this process is the first step toward innovation and discovery. Generally, the micro-engineering research is followed by macro-engineering development. In the production environment, there are generally more development projects than can be accomplished in a timely manner. Usually, this is the result of financial and human resource limitations. Consequently, it is necessary to prioritize the work such that the most beneficial projects are accomplished first. By performing a discounted cash flow analysis and using benefit-cost ratios (for non-mutually exclusive alter¬natives) or net present value criteria (for mutually exclusive alternatives), the projects can be rated from best to worst. In this way, the financial and human resources can be best allocated to first complete those projects giving the highest returns before moving on to other activities. Moreover, this information is a prerequisite for management to justify additional financial or human resources.

Jan 1, 1992

By T. J. Jr. Corwin

This paper will cover the problems confronting an owner when planning and estimating the cost of a proposed tunnel. Three factors are known: the length, size and the time allocated for the completion of the work. In general the difficulties encountered when driving a tunnel in California are the greatest at the lower elevations and in the Coast Range and are minimal in the Sierra Nevada mountains particularly in granitic formation. The writer will discuss the experience gained from observing the driving of about 120 miles of tunnel in California as well as the repairs of some tunnels. SIZE OF TUNNELS It is known that a small tunnel may be more costly to drive than one of somewhat larger dimensions. This fact was found to be true when a tunnel about 4,000 feet long was constructed to eliminate 7 miles of canal. The formation was lava so it was anticipated the ground would be self supporting because of the small bore. Actually the tunnel required support for most of its length and working conditions were poor. It became apparent that a larger size could have been driven at no additional cost and probably in less time. On another unlined tunnel, to be driven in granitic formation, the contractor was given the option of using

Jan 1, 1974

By Adam Graf

Mineral deposits are fundamentally different from most other assets -Every deposit has unique geologic and metallurgical characteristics -Asset (resource) is finite and cannot be truly replaced. -Long timeframe and time-value of reserves -Commodity price volatility (see Torries, 1998)

Jan 1, 2003

By R. Gerling

A computer program has been developed for finding a near-optimum schedule of the mining sequence for flat lying, tabular orebodies. The deposit is divided in blocks with equal areas and definite grades, thicknesses and ore contents. Mining is done by room and pillar method and trackless haulage to surface. Access from surface is by adits or ramps with additional vent raises. In total eight different general concepts for access and development can be realized. The optimum mining sequence is found by a heuristic method. Criterion is the maximization of the net present value over the lifetime of the mine. Specific stoping costs per t of ore are taken for con¬stant, whereas development and haulage costs for individual blocks and also sequences will be different. Correct ventilation and a technically sensible sequence are guaranteed. Beginning with a single block, neighbouring blocks are tested and an optimum stoping sequence is generated. The net present value of the total mining operation for the planning period is calculated, taking into account ore, which is mined during development. The program can also be used to investigate given mining sequences.

Jan 1, 1986

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992