Search Documents

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By P. Chauvet

From a computational point of view calculating a variogram is a perfectly simple operation. For any particular study, we know which variable is to be studied. We also have a good idea of structural parameters which are likely to be important (the scale of the phenomenon, the probable direction of the anisotropy, etc.). Finally, we know the structure of the data file. So we can specify the parameters to be used to calculate the variogram (the distance classes, the angular classes, etc.). This allows us to decide which variogram program is most appropriate (1, 2 or 3 dimensional data, regularly or irregularly spaced, etc. ) . In general, the basic statistics (mean, variance, correlation? etc.) have been calculated beforehand, and so the distribution of the data is already known. Consequently, the choice of the parameter values fed into the variogram is by no means arbitrary. But it must nevertheless be made before the' variogram is calculated. If the resulting variogram is not satisfactory, the whole sequence of operations has to be repeated. Before going on to see how this can be avoided, it is worthwhile having a brief look at the common causes of "unsatisfactory" variograms.

Jan 1, 1982

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By Robert F. Randolph

New technologies confront mining organizations with unprecedented human factors challenges. Likely problem areas range from the design of the human- machine interface to the design of work groups and mine organizational structures. However, these human design considerations are commonly ignored in most industries, resulting in a failure rate of 75% for advanced technology programs. The U.S. Bureau of Mines is addressing these concerns through a program of research on the human side of high technology mining systems. Interviews with mining industry participants and researchers have identified concern in several areas, including training and equipment design. Although new mining technologies promise to improve overall safety by relocating miners away from hazardous areas, data from MHSA accident reports and other sources suggest that certain types of new hazards may be created. Many of these new hazards can be reduced though a systems approach to ergonomic design of equipment, tasks, and work processes. This evidence, combined with reviews of high technology human-machine systems in other industries. can help in the design of safe and efficient future mining technologies.

Jan 1, 1992

By J. C. Weimer

The goal of Bethlehem's mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll on the U.S. coal mining industry. Recent health surveillance data indicate that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied to reduce dust levels. An overview of CWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

By Hamed Khodadadi, Hamid Ghadiri

The ball mill grinding circuit has widespread application in mining, metallurgy, chemistry, pharmacy and research. It faces some challenges because a grinding circuit is a multivariable system in which high interaction between loops, variation of system parameters with time, and time delays are problems. In this study, a fuzzy logic self-tuning proportional–integral–derivative (FLST-PID) controller based on an improved disturbance observer is designed for control of ball mill grinding circuits. It is combined with an improved disturbance observer (IDOB) to eliminate system interaction, attenuate internal and external disturbances and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit.

By A. Cavero, M. Diaz

The annual rainfall at Minera Yanacocha's gold mining operations in northern Peru averages 1.2 meters. The influx of water into the operations is higher than losses to evaporation and by ore absorption which results in a positive water balance. To minimize water intake and maintain a balance, some special operating procedures are required, and a system involving diversion ditches, storm ponds, heap skirting and detoxification and treatment of excess water is practiced. An operation background is also reviewed at the beginning of the paper.

Jan 1, 1998

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By Terrence Chatwin, Michael Sweeney, Steve Accardo

Sutter Gold Venture excavated an exploration decline into a mineralized zone in the Sutter Creek gold mining district. Delays in obtaining the conditional-use permit resulted in 7 to 10 million gallons of water accumulation in the decline containing elevated dissolved arsenic. Sutter received a permit to land apply the water after reducing the arsenic concentration to 0.05 mg/L. Initially the water was treated by co- precipitation arsenic with ferric hydroxide. Operational difficulties of this treatment system resulted in Sutter pursuing alternative treatment methods. The activated alumina adsorpting was selected due to its flexibility and ease of operation. Operating and maintenance data and costs will be presented.

Jan 1, 1995

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rockmass strength. Past studies have largely used arbitrary scaling approaches to produce rockmass strength from laboratory rock tests. This paper proposes a stochastic approach to produce rockmass strength from laboratory rock tests. Based on the laboratory data, MATLAB with an extreme value stochastic model generated a database for each physico-mechanical property of the rock. Then finite-difference software FLAC2D simulated laboratory-sized rock specimens. Random material properties in MATLAB were generated using the grids developed in the numerical model. The random properties were then applied to the final FLAC2D model. Model runs simulated the approach performed in the laboratory. The results from the model indicate that a stochastic approach produced compressive strengths that were lower than those from the deterministic approach. Failure modes for each specimen were different from those observed in the laboratory. In addition, random density also influenced the failure mode, highlighting the importance of stochastic analysis in rocks.

By W. H. Langer

Natural aggregate is the number one non-energy mineral resource in terms of value and volume and is a necessary commodity for sustainable communities. While aggregate is a non-renewable resource, supplies are nearly inexhaustible on a global scale. Natural aggregates have characteristics that differentiate them from most other mineral commodities: a high number of potential extraction sites, a high volume to value ratio, significantly different set of potential environmental impacts, and regional importance combined with a narrow economic transportation radius. Because of these and other differences, resource management policies for aggregates should differ from ?general? mineral resource policies, even though the end goal is the same for both ? ensuring sustainable resource management. To achieve the goals of sustainable aggregate management each stakeholder ? government, industry, the public, and non-governmental organizations ? will need to accept certain responsibilities, one of the most important of which is to become informed about natural resource issues. Sustainability is about making trade offs among competing objectives, and people disagree about the appropriate balance among the goals of economic prosperity, social equity, and environmental health. One of the primary purposes of mineral indicators is to provide information to decision makers and the public so as to ensure that the public debate about policy choices is grounded in fact. We identify the unique aspects of aggregate resource management and introduce the concepts of sustainable mineral resource management. We then present mineral indicator sets for aggregate resources from Italy, the United Kingdom, and Slovenia to demonstrate that effective mineral indicators should be specific to the resource in question and the public values and objectives.

Jan 1, 2003

By Louis W. Riggs

The primary concern in dealing with contractual arrangements for construction is getting the work completed satisfactorily, in the shortest time, and for the least expense for the owner--while assuring that all other parties associated with the contract make a reasonable profit for their effort. In our complex construction climate of today, achieving all of these is usually not possible. Somewhere between the beginning of design and the completion of the work, disagreements and delays arise which can destroy the best of intentions. Assuming that all parties associated with the contract are acting honorably and professionally, the disagreements generally arise through inappropriate contract types or through flawed contract documents. These flaws can be either sins of omission or commission, but we must find a way to lessen, if not completely eliminate, their impact. Disagreements and delays are directly related to the extra cost which the owner and the other involved parties must suffer. Usually the attorneys are the only ones who come out on the positive side. Inappropriate or defective contract documents can be the result of inadequate time for preparation and review, laziness in not searching out the proper terms and language, insufficient recognition of the proper assignment of risks, or just ignorance as to what is right and what is wrong for the particular project. They can also result from a client, particularly a public agency, providing rigid general conditions and format requirements with which the engineer is not allowed to tamper. Arguments

Jan 1, 1979

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By Dalva L. Moellenberg

Introduction Hard rock mine closure (often referred to as decommissioning), mined land reclamation and financial assurance requirements are receiving considerable attention by governments and organizations around the world. In the United States, federal agencies and the states continue to consider and make changes to laws governing mine closure and mined land reclamation, most of which were originally enacted in the mid-1970’s through the mid-1990’s. Internationally, a number of prominent groups and various countries currently are considering new laws, regulations and policies for mined land reclamation. For example, the European Union has conducted a review of existing European laws concerning mining wastes and mine water and is considering new directives concerning mine waste and mine water management and liability schemes that are likely to significantly impact mine closure and mined land reclamation. Many countries, particularly those outside of North America, Europe, and Australia, have recently adopted or are considering new mine closure and reclamation legislation and regulations. These include significant hard-rock mining countries such as Chile, Peru and South Africa. This paper identifies recent developments in hard-rock mine closure and mined land reclamation laws in the United States, focusing on several of the more significant and controversial developments. It also discusses some of the more significant international efforts to consider mine closure and mined land reclamation laws and policies and some of the notable conclusions and trends from those efforts. The focal issues discussed in this paper include requirements for the reclamation of open pit mines, including backfilling; consideration of and measures to address the mining of sulfide ores and potential for acid mine drainage; and new requirements for the estimation of closure and reclamation costs and for financial assurance for closure and reclamation.

Jan 1, 2005

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By M. Elzeky, A. Attia

The effects of bacterial adaptation and partial replacement of leaching solution on the rate and extent of bioleaching reactions of a complex sulfidic gold ore were investigated. The ore was first concentrated by bulk sulfide flotation and the sulfide concentrate was treated by bioleaching using T. Ferrooxidans bacteria. The residues from bioleaching were treated by cyanidation to extract the gold and silver. Bacterial adaptation before bioleaching significantly increased the rate and extent of bioleaching reactions. Similarly, the daily partial replacement of leaching liquor enhanced to a great extent the leaching rate and in some cases up to ten fold increase was observed. Both bacterial adaptation and solution replacement increased the gold recovery by about 2-fold and that of silver by about 1.3-fold. In this work more than 95% of the gold and more than 98% of the silver could be recovered from the sulfidic gold ore, when bioleaching was used ahead of cyanidation compared with 18.3% and 52.3% by direct cyanidation.

Jan 1, 1989

By Alfred A. Roetzer

In several sections of the country new demands are being brought bar cement users. Among these the demand' for truck shipments; and palletized loads present new problems that do not lend themselves to sample solution. In fact these demands have far-reaching effect in the way bagged cement might be marketed. Early solutions of palletized truck loads filled from existing packing and loading facilities have resulted in' slowdown in packing, additional labor and space for palletizing, considerable experimentation in type and construction of pallets, and usually far from optimum truck handling and loading methods.

Jan 1, 1961