Search Documents

By Claus Becker

At the RETC 1979 in Atlanta/Georgia it was reported about the beginnings of the Hydroshield system and the first site experiences. Since that time over 10 miles of tunnels in various diameters have been built with that system, and the discussion of the two most interesting projects will be the main topics of this paper. AURELIA TUNNEL, ROME In Rome, the railway system is going to be completed and modernized. Therefore, it is necessary to tunnel through the Roman hills. Part of the new railway system is the Aurelia Tunnel, located some 100 feet below the famous Via Aurelia Antigua, close to the Vatican. The double track railway tunnel has an internal diameter of 9.44 m and a length of 2.410 m. It runs through completely differing soil conditions. (Fig. 1) The first 1000 t are situated in watertight clay, the rear part in water bearing loamy, clayey sands with interlayers of loamy clays. The figure shows the soft change-over from clay to sand. The groundwater head is between [ ]

Jan 1, 1983

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980

By Z. T. Bieniawski, Christopher Mark

A new method for the design of long- wall chain pillars, called Analysis of Longwall Pillar Stability (ALPS), is described. The method provides estimates of the relative stability of different longwall pillar designs during all stages of their service life. The key issue addressed by ALPS is the magnitude and time-of-arrival of the longwall abutment loads applied to chain pillars. A field study was conducted and other available field data were analyzed in order to develop an approach for estimating the abutment loads. An example based on longwall experience in the Pittsburgh seam is used to illustrate how ALPS can be used in mine design.

Jan 1, 1986

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By James P. Dorian

In 1990, the former Soviet Union ranked first worldwide in the production of asbestos, chromium, iron ore, iron and steel, lime, manganese, mercury, nickel, peat, potash, and titanium. Since the middle of this century, that nation had maintained one of the world's most valuable mineral industries, ranking number two in 1950 and number one in 1990. It is clearly an enormous mining industry, with more than 1300 enterprises and an estimated employment base of 1.2 million persons (Table 1). Despite its size and historical achievements, however, the mining industry of the 1990s in the former Soviet republics is encountering problems in performance, efficiency, transportation and utilization. The industry operates below full capacity and is plagued by outdated technology and equipment, rising production costs, capital shortages and labor strikes, in addition to general economic deterioration and civil unrest. Attempts to boost domestic minerals supply in the republics so far have failed because of economic difficulties. And the republics lack the financing required to initiate new, large-scale development projects.

Jan 1, 1992

By J. R. Parry

Over the past several years, computerized financial models have been an important part of Newmont's strategic planning process. Two applications will be discussed in this paper: a general purpose financial model of Newmont, and a detailed operational/financial model of Magma Copper Company. Newmont?s general purpose financial model was developed using Lotus 1-2-3. It was designed to aid management in assessing the financial consequences of investment and financing decisions associated with long-term strategic planning by simulating the consolidated effect from individual transactions. Not only is the model capable of assessing the sensitivity of specific decisions to changes in the external economic environment (i. e., commodity prices, interest rates, inflation and exchange rates), it can also evaluate the effect from operating and financial decisions, including changing production levels and cost structures at individual operating units as well as simulating several types of transactions, including equity and debt issues, acquisitions and divestitures. The analysis of Magma Copper Company required the development of a detailed operating and financial model of the Company. The model was developed using IFPS in the corporation?s UNISYS (then Burroughs) B7900 mainframe computer and included separate pro forma financial statements for each of San Manuel-Pinto Valley's mines and concentrators, as well as Magma's smelting and refining operations. The outcome of this analysis was the decision to merge Magma Copper and Pinto Valley Copper Corporation, and to recapitalize the new corporation in order to provide funds for a retrofit and expansion of its Arizona smelter and expansions of its refinery and SXEW facilities.

Jan 1, 1989

By G. M. Wilemon, Swanton. R. G.

The Bureau of Mines is investigating the leaching of phosphate values from Florida phosphatic clay wastes using sulfuric acid (H2SO4) as the leaching agent and methanol as the solvent. Acid-alcohol leaching studies were done using research-grade apatite to investigate potential causes of flow extractions. It was found that a barrier layer formed on the surface of the apatite. Initial discovery of the barrier layer was made by analyzing pure apatite samples before and after leaching using an optical microscope. Subsequent Fourier Transform Infrared (FT-IR) analyses proved the coating was calcium sulfate hemihydrate (CaSO4•1/2H2O) and that unreacted apatite existed beneath the coating. Scanning electron microscope (SEM) photographs depict the CaSO4• 1 /2H20 morphology as long slender crystals adhering to the apatite surface. It was also shown that grinding the leached tailings and leaching again in the H2SO4-methanol system resulted in additional phosphate extraction.

Jan 1, 1992

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By Thomas P. Kwiatkowski, Len Cobb, Christopher D. Orlandi, Judith H. Jones

The Inland System supplies raw water to the industrial and domestic users in the City of Birmingham, Alabama. The Inland System, which is nearly 60 years old, consists of an approximately 57.9m (190 feet) high earthen dam across the Blackburn Fork of the Black Warrior River, a 39.6m (130 feet) high reinforced concrete intake structure, a 1524mm (60inch) diameter Dresser coupled steel transmission pipeline, and various distribution lines extending into Birmingham. The Inland System was owned, operated and maintained by the Industrial Water Board (IWB) of the City of Birmingham, an agency of the city government, from 1958 until 1994. In 1994, the City of Birmingham consolidated all water and distribution functions under the Birmingham Water Works Board (BWWB). In 1988, the IWB determined that the Inland System had reached a point where its reliability could not be assured without an in-depth evaluation and renovation. The IWB engaged Christy/Cobb, Inc. (CCI) of Birmingham as its consultant for the renovation work. CCI evaluated the Inland System and submitted a report to the IWB in April, 1992. The report contained several recommendations for capital improvements to the system including increasing the emergency spillway capacity, reconstructing the fuse plug, relocating public access to the lake away from the dam area, constructing a new intake structure, and constructing a tunnel through the dam abutment to deliver the water from the proposed intake structure to the existing 1524mm (60 inch) diameter supply line. The new intake structure and tunnel would provide for a future maximum demand flow rate as well as provide bypass and level control capabilities. CCI was authorized in 1992 to proceed with the engineering design for the renovation of the Inland System with emphasis on the spillway and intake structure. PROJECT DESCRIPTION The major component of the renovation of the Inland System was the new intake structure and tunnel through the dam abutment. CCI engaged Jenny Engineering Corporation (JEC) of Springfield, New Jersey as a consultant for the tunnel design. JEC was responsible for the design of the tunnel, the connecting shaft between the intake structure and tunnel, and the steel pipe final lining, while CCI was responsible for the intake structure and the connection to the existing supply pipeline as well as overall project management. CCI and JEC evaluated the project site in order to select the location for the new intake structure and set the alignment for the tunnel. A factor in the evaluation process was that the level of the lake could not be lowered to construct the new intake structure since the supply of water from the Inland System had to maintained. Therefore, a location was required which was

Jan 1, 1997

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, large-scale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in the city of Chifeng in China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading.

Jul 1, 2023

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

By Jim W. Rosteck, Anthony Del Vescovo

In December of 1992, the City of New York, Department of Environmental Protection, solicited bids for Contract 543B. The low bidder was a joint venture of Schiavone Construction Co., Inc. and the J. F. Shea Co., Inc. When completed, the project provides a 4.88 meter diameter water tunnel 8,840 meters long. This paper presents a case history of the equipment and construction methods utilized for this, the first portion of the New York City Water Tunnel constructed by use of a tunnel boring machine.

Jan 1, 1997

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By N. Arbiter

During the first four decades of flotation practice, close to 200 machine designs were patented, although only about a score were ever used commercially. By the end of that period, the rigors of use had resulted in obsolescence of most pneumatic cells, with a few mechanical cells dominating the field. After World War II, newer designs began to appear but most were modifications in varying degrees of older designs with special features added. Of the dozen or so most recent developments, almost all are pneumatic, relying on compressed air instead of impellers for motive power, although in several cases pumps supplement compressors. Table 1 lists a few of the more fully documented new cells, with their significant characteristics, along with similar characteristics of a widely used mechanical cell. New designs in general are emphasizing: bubble size control; in several cases, methods for delivering feed directly to the froth; methods for introducing and dispersing air through nozzles, eductors, packed beds, or permeable walls; and variable cell volumes, relative to capacities, ranging from very small, with less than a second of retention time, to the largest, with retention times of over 20 min. An important question is the extent to which any of the newer designs are based on locating weaknesses in current mechanical cell designs and then using these as a starting point for innovations. In the present study, the key subprocesses which must take place in a cell are outlined; mechanical cells are analyzed to establish where weaknesses may exist; and then alternative subprocesses are considered which could effect improvements. COMPONENTS FOR CELL DESIGN It is assumed that mineral surface chemistry has been modified as necessary to provide optimum potential floatability. While the cell process may affect this to a degree, cell design is primarily concerned with actualizing the existing potential floatability. The cell design problem is to provide more effectively for the following: 1) Dispersion of air to obtain an optimum bubble size distribution at an optimum ratio of air volume to feed volume. 2) A hydraulic environment which permits most effective contact of potentially floatable particles with bubbles: [Table I - Cell Comparisons* Cell Type Mechanical Column Deister Miller ASH No. of units Multiple Single Single Single Retention time min.10/20 17/27 3.8 ca. is Capacities mt/m3s 0.022/0.066 0.066/0.20 0.11 10.4 st/ft3d 1/3 0.3//0.9 m5.0 469 Air hold-up % 15/20 20 n.a. 50/80 Air escape velocity m/s 0.015/0.0200.020/0.025 n.a. n.a. ft/m 3/4 4/5 n.a. n.a. * References: Mechanical (Harris, 1976,1985), (Bassarear, 1985); Column (Travis, et al. 1987); Deister (Zipperian and Christophersen, 1985); ASH (Air-Sparged Hydrocyclone) (Miller 1989).]

Jan 1, 1989