Search Documents

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. 'ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering' and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970's (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By K. M. O’Connor

Time Domain Reflectometry (TDR) is a pulse testing technique developed by the telecommunications and power industry for use in locating breaks in cables. Variations of this principle have been utilized in applications pertinent to closure and reclamation of coal operations. This paper focuses on applications of TDR technology in the mining industry including monitoring of slope movement, abandoned mine subsidence, ground water levels and subsurface LNAPLs, landfill cover performance, and consolidation of mine tailings. TDR technology has been particularly effective for remote automated monitoring, and alarm systems have been implemented for monitoring subsidence.

Jan 1, 2003

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By A. A. Odunaike, E. G. Okafor, M. H. Mokwe

Microscopic Studies were performed on ore samples from the Muro banded iron ore deposit in Nigeria and the Marampa iron ore deposit in Sierra Leone. Ore characteristics that affect processing of both ores were compared with a view toward assisting mineral processing engineers in choosing the most suitable methods for upgrading the ore. The Nigerian ore contains 30% to 37% (by weight) Fe and the Sierra Leonean ore contains 34% to 51% (by weight) Fe. Hematite is the main iron mineral in both ores. The Sierra Leonean ore is relatively coarse grained (typically around 250 µm) and can be upgraded by conventional gravitational methods. In contrast, the Nigerian iron ore is fine grained and must be ground to -74 µm to liberate the hematite for recovery by flotation. Both ores contain high percentages of phosphorus and sulfur, which are above the required specifications for direct reduction and blast-furnace practice. These deleterious elements can be rejected by grinding and flotation.

Jan 1, 1999

By Peter W. Harben

Once considered the dowdy country cousins of the glamorous metallics, industrial minerals are shedding their old image. They are neither common nor easy and their time has come in an age of increasing specialization. Consider that of the 45 or so industrial minerals and rocks listed in [Table 1], almost three-quarters have ten or fewer significant suppliers (i.e., those individual countries contributing 2% or more of total world production); in more than half the cases, 85% of world production is accounted for by only five countries or fewer. Curiously, even materials that appear to be virtually ubiquitous like crushed rock and common salt have significant production vacuums. For example, there is a severe lack of sound aggregates along the US Gulf Coast and common salt production on a large scale is virtually absent in central Africa. These examples all underline the obvious, but acute truism that "The single most important fact about mineral resources is that they are not distributed equally over the world" (Flawn, 1966). Just as significant today is that human resources are not distributed equally over the world, and so arise some interesting commercial incongruities. In certain regions raw materials are plentiful but consumers are not, and without a market a mineral deposit is merely a geological curiosity. Elsewhere, there may be a market but no local raw material supply. For example, despite a huge market there is no or virtually no commercial production of chromite, diamonds, and manganese in the United States and Canada, nor phosphate rock, diamonds, rutile, and zirconium minerals in western Europe. In contrast, Australia with its small domestic market is the world's largest supplier of bauxite, diamonds, ilmenite, natural and synthetic rutile, and zircon; the same is true for South Africa which is a leading producer of chromite, manganese, diamonds, andalusite, ilmenite, rutile, and zircon (Table 2). In the commercial world, Nature's uneven distribution is counterbalanced by deep sea international trade.

Jan 1, 1994

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By S. Siewierski, L. Wojno

INTRODUCTION Bumps are among the most dangerous hazards in the Polish copper ore mines. Their occurrence is the result of the dynamic processes in the rock mass caused by natural factors connected with the deposition of strata and, to some extent, by technological factors resulting from the process of exploitation. In this connection, in order to ensure worker safety and choose such a technology that allows an achievement of high technological and economical parameters, a detailed knowledge of the phenomena occurring in the rock mass is required. In copper mines the basis for forecasting and control of bumps is obtained by continuous measurements and observations of the symptoms of rock mass pressure, the analysis of which ensures the accuracy of forecasting and points toward preventive means that must be applied to prevent bumps. The methods most often used for preventing bumps in copper mining are discussed in this paper.

Jan 1, 1982

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By C. G. Janes, N. Finkelstein, L. M. Jr. Johnson

In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V- loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: Ore Grade 0.32% Cu., 0.030% Mo. Daily Tons Milled 90,000 STPD Annual Copper Production 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces

Jan 1, 1976

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By L. Adler

When systematically compared to other engineering fields, mining engineering is distinctive in 1) having a total systems concern. 2) dealing with encumbered space and 3) requiring full spectrum practice. The total systems concern results from having to design and then co-ordinate in space and time several major systems: excavating and bulk handling, ground control, life support and normal support. This requirement favors a generalist rather than a specialist approach. In coping with encumbered space especially in underground coal mining, the uncertainties of geologic conditions are compounded by tightness, roughness, remoteness and hazards. Into this difficult setting the total systems * complex is "stuffed," adding congestion and interference. Because of significant ground deterioration a flexible "rapid in-out" approach is usually vital to mining. Full spectrum practice arises from the need to manage, as well as to plan and design, a labor intensive operation. Since market conditions can also fluctuate most aspects of administration are needed in many respects, mining engineering functions relative to civil engineering in a way similar to industrial to mechanical engineering, with encumbered space being crucial. On this basis stress is placed on: 1) personal relations, 2) field work and 3) entrepreneurship, viewing time as money. Specific recommendations for improving engineering, safety and management and leadership are made. Since most new deposits are marginal, by applying these recommendations with high technology they could possibly now be mined on a widespread basis.

Jan 1, 1985

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By David R. Baughman, Ray V. Huff, Paul D. Chamberlin

ISL Ventures, Inc. (ISLV) is developing a process for recovering gold and silver from ores using a chloride-hypochlorite lixiviant. The leach solution, composed of water, NaCl and NaOCl, is maintained at a pH of about 7. At this pH most base metals are not leached. This is important for deposits that contain cyanide-soluble copper. An inhibitor can be incorporated to slow the decomposition of the oxidant. This paper reviews the history of development, presents details of the chemistry and indicates the nature of deposits, which we believe to be amenable to production using the process.

Jan 1, 1999

By Richard C. Fountain

The Central Florida Phosphate District is located in southwestern Polk, southeastern Hillsborough, Manatee, and Hardee Counties, Florida, flanking the.southern end of a major structural uplift known a the Ocala arch. Ore control problems here are varied and unique due to non-homogeneity of matrix and high volume mining operations. Overburden stripping and matrix mining are performed by large draglines, the matrix being slurrified and transported to the processing plants hydraulically. Production geologists' responsibilities include, 1) prediction of special mining problems, 2) prediction of ore quality and quantity, and 3) the physical control of the ore quality and recovery during mining. prediction is based on core drilling and visual inspection and analysis of the core samples. Basic economic, and physical minability criteria are thus established. Ore grade and tonnage recovery are of particular importance with emphasis being placed on coordination between mining and processing personnel. Routine inspection of the working pit face is of prime importance and both physical and quality variations are pointed out to the mining supervision. Physical problems in ore control occur due to erratic clay, dolomitic limestone and sand lenses. Near surface ground water is abundant, posing a threat to recovery. Contaminants of the phosphate ore are large quartz grains, pebbles of cemented quartz sand, clay balls, iron oxide laminac and dolomitic limestone particles. Success of the ore control program is predicated on a balance between predicted ore tonnages and grade and actual production. The geologists' primary attention is directed toward this balance.

Jan 1, 1972

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986