Search Documents

By Lukas Erkurt, Wolfgang Holzer, Stefan Auderer, Richard Gradnik

SEM/ NATM Tunnelling contracts in Austria and Germany are usually tendered applying unit price contracts. The purpose of this paper is to show how contractual problems are resolved in these countries. The focus will be put on describing the theoretical approach, several case studies will show how contractual problems were dealt with on site.

Jun 23, 2024

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today&apos;s DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine&apos;s ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By S. D. Thompson

Since 1965 several researchers have independently developed computer models for designing gathering belt and surge bin capacities in underground coal mine belt systems. Table 1 summarizes the models applicable to U.S. mining systems. Most of the models, employ the Monte Carlo simulation technique. Basically, the belt loading at each loading point is randomly produced from probability distributions. In some cases, a combination of deterministic calculations and probability distributions are used to simulate the loading. Once the loading is simulated, it is systematically moved through the belt system in a deterministic fashion based on belt speeds, belt lengths, and storage bin discharge rates. The coal flowing from each loading point is tracked as it moves through the belt system. When the loading from tm different sources combines on a belt or in a surge bin, checks are made to determine if capacities have been exceeded. If capacities have been exceeded the amount of spillage is calculated. At the end of the simulated time period, the cumulative spill- age is used to evaluate the belt and surge bin capacities. Naturally, a considerable amount of spillage indicates the capacities are unacceptable. Acceptable capacities are generally indicated by minimal spillage. Numerous trial simulations are often necessary to find the acceptable capacities.

Jan 1, 1987

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By Jason Clarke, Glen Trainor

As the mining industry faces increased challenges with declining ore grades and harder to access deposits, operating mine sites in an environmentally responsible and economically viable manner will require innovations that improve efficiency in energy logistics, and automation. Technological advancements in mining have been successful primarily because of the willingness and capability of these solutions to share information with one another, for example OEM payload systems sending information to Fleet Management Systems, and in turn Fleet Management Systems interfacing to ERP systems. To promote and facilitate the sharing of data, there has been a push towards open standards with initiatives led by organizations like ISO, ISA, EMESRT, and GMG. These efforts are aimed at creating a more collaborative and interoperable environment within the sector. However, when it comes to implementing autonomous solutions, a different trend dominates— closed-stack solutions. These closed stack solutions not only prohibit a mine site from selecting best-of-breed solutions, by blocking the competition from entering the market, they also risk slowing innovation that could help overcome the challenges the mining industry faces. Open Autonomy, an internationally published standard that allows any FMS to work with any Autonomous solution, breaks this closed-stack approach and invites competition from other industries. This competition comprises of autonomous suppliers from other industries and manufacturers of smaller, civil-sized haul trucks. The availability and capabilities of these smaller-sized autonomous haul trucks will help tackle the challenges of responsibly and economically mining lower quality ore grades and mining harder to access deposits.

Feb 1, 2024

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

For the first time, surface subsidence prediction theory was used to investigate roof movement around longwall face mining in a steeply dipping coal seam. A physical simulation experiment was conducted to quantitatively study the roof migration patterns, the gob materials, and the characteristics of bed separation and compression caused by mining two adjacent panels to gain a better understanding of ground control issues in multipanel mining in steeply dipping seam. This approach provides an in-depth analysis of the movement of the roof. Compared to movement observation of survey point using total station, the Photogrammetry Analysis for Physical Modeling of Mine Subsidence Program (PAPMMSP) method is easier to perform, faster and yields the much higher accuracy required for scale physical modeling. It is also a more effective observation method for underground-mining physical simulation experiments.

By Robert T. Chapman

Many of us are privileged in that we have witnessed the transition from mining methods used in the first quarter of the twentieth&apos; century to those practiced today. In the late Twenties, for example, many mines still used hand mucking methods. In the middle Thirties, more than one large metallurgical limestone quarry still used the 4 cubic yard railway steam shovel formerly in use at the Panama Canal. Mules could occasionally still be found underground, where they provided the-main-source of motive power. Within the last decade, and even within the past five years or less, great improvements have been made in blast-hole drilling, ore loading, and ore hauling equipment. Industrial demand for minerals can be expressed in exponential terms as compared to that at the turn of the century. Even marine mineral resources are receiving accelerated attention. One overall result is that larger and lower grade orebodies can be exploited at a profit. This profit must be made despite, for example, a static monetary price for gold, and despite the continual cost escalation involving labor, materials, supplies, and equipment. Accordingly, the application of the necessary degree of knowledge and judgment required to meet production, cost, and profit goals is paramount.

Jan 1, 1966

By James R. Taylor

24.1-BASIC PRINCIPLES JAMES R. TAYLOR The basic principle involved in maintenance is protection of a company&apos;s investment through the care and upkeep of machinery and equipment, buildings and properties. Maintenance is justified through making available to the maximum extent possible the facilities, machines and services required by the operating and production departments in their function of insuring optimum return on investment. As the size, cost and complexity of the equipment used in modern mining and related industries increase, operating and production personnel become proportionately more dependent upon maintenance engineering for its contribution to the overall profit picture. A greater part of the total cost now is charged to maintenance and the maintenance group becomes a major company unit. Basic maintenance concepts have changed very little over the years, but the advances in methods and technique have brought about tremendous challenge and have in consequence assumed a greater influence and importance. The older "sledge- hammer" methods have given way to engineered and scientific systems, while the accelerating development of intricate equipment and machinery, and the instrumentation essential for control, demand an ever-increasing upgrading of maintenance personnel. Regardless of this growth in importance, cost and complexity of the maintenance function, it is important to remember that it is not an independent and self-sufficient unit, but is a necessary facet of the entire plant operation and is subject to the company&apos;s total production effort. As one part of a team, maintenance is successful only when functioning cooperatively wit11 the other departments it serves Close collaboration in all areas served by n maintenance group is essential if it is to function fully to protect the company&apos;s investment, whether the assets are in machinery, materials or people. 24.1.1-MAINTENANCE SCOPE Maintenance functions may be grouped into the two general classifications of primary and secondary. This grouping constitutes a basic division although, in practice, the scope of the maintenance activity varies in each mine or plant and is subject to differences in size and type of operations and company policy, plus the influence of precedent, which may be sectional or industry-wide. The primary functions supply the justification for the maintenance engineering department. while secondary functions are variable according to plant conditions and needs. The primary functions may be categorized as follows: 1. Maintenance of existing machinery and equipment. 2. Maintenance of existing buildings and grounds. 3. Inspection and lubrication of equipment and machinery. 4. Utilities generation and distribution. 5. Alterations to existing equipment and facilities. 6. Installation of new equipment and facilities. 7. Instrumentation.

Jan 1, 1973

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator&apos;s position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By D. G. Purdy

Planning, as defined in Webster&apos;s New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010