Search Documents

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By Dan B. Kivari

One of the key operations in any milling circuit is grinding. Over the last two decades, large diameter Semi-Autogenous Grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Whereas earlier most SAG mills were designed to operate at fixed speeds, present day SAG mills can operate at a fixed speed or variable speed through the use of an AC synchronous motor or DC motor. However, this flexibility comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on Net Present Cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors such as reliability of mill drives and power source are important elements in the decision making process. This paper examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1991

By Brent A. Elliott, J. Richard Kyle

This article reviews the production trends of industrial minerals since 2000 for Texas, the leading U.S. producing state of industrial minerals with a total value of $5.2 billion in 2017, equivalent to 6.9 percent of all U.S. minerals value. Most current Texas industrial-mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is concentrated in the 25 metropolitan areas of the state, with production of industrial minerals in nearby counties. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to meet in-state and regional demand. Texas’ most rapidly growing production of industrial minerals is industrial sand to supply proppants for multiple unconventional petroleum plays. Texas’ favorable geology and economic factors provide opportunities for the identification and development of new industrial-mineral production sites. Repurposing of former industrial-mineral production sites for post-production development likely will increase as efficient land use evolves. Understanding the geologic, economic and societal framework of industrial-mineral resources will facilitate more informed decisions about the complex issues that the region will face, including effects of sea-level rise on coastal infrastructure.

By EREN KOMURLUR, ATILA GURHAN CELIK, IBRAHIM GUNES

In this study, laboratory and site studies were performed to investigate the usability of a new insertion apparatus designed for the split-set type of friction bolts. The new apparatus decreases the friction during the bolt insertion by a temporary diametric compression of the split tubes. According to the results, the new precompression apparatus was found to be advantageous in terms of the insertion practicality and prevention of the buckling problem. By allowing increases in the ratio of bolt diameter to drill-hole diameter, the new apparatus was found to supply relatively high normal stresses and friction capacity in drill holes after opening its clamping mechanism.

By H. Colijn

Introduction Bulk commodity prices are ever increasing. This forces buyers and sellers in world markets to look more carefully at methods for obtaining an accurate accounting of commodity transactions in commerce and materials utilization in processes. Weighing and sampling inaccuracies can result in loss of income, product quality, and cost controls. So weighing and sampling accuracies are extremely important. They are the key components of managing the quantity and quality control aspects of bulk materials handling. This article will confine itself to the weighing systems and will deal with various aspects of system design, calibration, and operations. Emphasis will be placed on new developments and requirements in this field. Weighing methods To measure the gravimetric pull on a body being weighed (the load), the gravimetric force must be countered by an opposing force. Measuring this counter-balancing force thus becomes the measurement of weight. The conventional even-arm balance shows the concept of balancing an unknown mass with an equal known counterbalancing mass. But the loads encountered in industry generally range up to many thousands of pounds. So it is obvious that the even-arm approach is not practical. Thus, with the exception of direct load-bearing load cells, most of the weighing equipment uses some form of lever system. This is usually a combination of first- and second-class levers, to gain a mechanical advantage. These levers permit the load force to be counter-balanced and hence measured within a practical range. Lever systems not only perform this force-reducing action, they also serve to focus the load force at a single point, for convenient measurement. They align the force vertically in one direction so that measurement accuracy will not be affected by unrelated side forces. There are five basic methods of gravimetric weight measurements. That is, there are five basic types of opposing forces. • The first is the standard weight counterbalance. It uses a known weight to counterbalance the load directly or through a lever system.

Jan 9, 1988

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By Gürkan Bacak

Study area is located on the NorthWestern of Yatagan-Yenikoy and placed in the units of the crystaline Menderes massif of Eagen, Turkey. Stratigraphically gneissic, migmatitic and metagranitic rocks are found at the base. Garnet schists, phyllitic rocks lie unconfirmitelly upon the basement rocks. Permian aged marbles can be observed as diferrent sized lenses within the schists. Triassic, Jurassic and Cretaceous aged gray colored dolomites and pure crystaline calcite bearing marbles lie upon the Permian aged schists. Neogen series, mainly composed of conglomerates, claystones, marl and limestones unconformly cover the other basement series, mentioned above. Pure calcite bearing marble occurances are found at 2 locations in the study area. These are known as Berber Quarry and Kavuk Quarry. Samples numbered as N7, N8, NA from the Berber Quarry, mineralogically composed of Calcite (97-99%)+iron oxide (1-3%) and chemically contain CaCO3 (97,98%), Fe2O3 (0.5-1%), SiO2 (0.025%) N9 and N10, sampled from the Kavuk Quarry-mineralogically composed of Calcite (94,95%)+iron oxide (2-3%)+albite-Quartz (1-2%) and chemically contain CaCO3 (92-93%), SiO2 1.49%, Fe2O3 0.42%. Especially in plastic and paint sector albite and quartz are unwilling minerals due to their hardness. Approximatelly 1/20 of the study area (87.500 km2) contains industrial calcite occurances. Moreover about 100 billion Tons geological, 1.86 billion tons runable (possible) calcite reserve calculated. It can be expected the calcite quality will be increased with depth. During the running stage of the quarries over burden removel and hand sorting processes will positive affect of the quality.

Jan 1, 2005

By John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau of Mines philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry's needs. The Bureau of Nines programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine comnications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved nine communications systems.

Jan 1, 1976

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT The primary objectives of any field data gath¬ering effort should be to (1) identify and gather the data necessary for the project and (2) obtain the data in a state-of-the-art manner. All too often the initial field data are collected both areally and tem¬porally in an illogical manner without the guidance of a conceptual model of the ground water flow systems involved or even a review of existing geo¬logic literature on the area of interest. The initial data collected frequently are of limited value while necessary basic reconnaissance information is miss¬ing. Initial field data should be collected with the intent of developing a hydrologic overview of the potential mine site and surrounding area. Ob¬viously, one of the initial objectives is to define the area requiring a hydrologic investigation. The data requirements should be identified by the time frame in which collection should be made and by the corresponding increase in sophistication of the data requirements with development and operation of the mine. The data requirements are summarized in Table 1. INITIAL LEVEL SITE INVESTIGATION Area Determination The initial task of any hydrogeologic investi¬gation is to determine the boundaries of the area requiring study. Obviously, the site of the proposed mine is included in the study area. The areal extent beyond the site may be determined from an eval¬uation of existing geologic and topographic maps. Those formations that overlie the ore body, the formations containing the ore body, and the formation(s) that lies immediately beneath the ore body are of direct concern for proper site recon¬naissance. Additional formations below the ore body may require study depending upon their thick¬ness, hydraulic conductivity, and degree of inter¬connection with the mine workings. This initial viewpoint identifies hydrostratigraphic units based strictly on geologic concepts such as mineralogy and structure. Formation outcrops, synclines, an¬ticlines, faults, and fracture and joint patterns are used to delineate the area of the site reconnaissance. The simplistic hydrogeologic environment (il¬lustrated in Fig. 3, chapter 2) requires that field data be collected via test wells and/or geophysical techniques. This approach is necessitated by the lack of surface features such as formation outcrops, streams, and springs. Fig. 5 (chapter 2) illustrates a slightly more complex hydrogeologic regime. The potential mine sites at locations A, B, C, D, and E each intercept a different ground water flow sys¬tem or combination of flow systems. Therefore, each mine location requires that a different area and size of area be investigated. A more complex geologic setting as illustrated in Figs. 6 and 7 (chapter 2) may be approached differently. The area included for the site recon¬naissance should encompass sufficient surrounding area to include the outcrops of those formations suspected of being influenced by the future mine. Even adjacent areas not suspected of being influ¬enced may be investigated if the formations of in¬terest crop out in those areas. Such an extension of the area of investigation would provide a greater regional understanding of the hydrogeologic properties of the formations (hydrostratigraphic units) of interest. Geologic Investigation The initial step before conducting the site re¬connaissance is to review all existing literature on the geology of the area. Existing information should be augmented with new exploration data on the dip, strike, thickness, and lateral extent of the for¬mations in the area. Exploration hole logs should be reviewed for indications of lost circulation, rub¬ble zones, and water producing zones. Existing aer¬ial photos such as those available from the US Department of the Interior, EROS Data Center,

Jan 1, 1986

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By D. D. Gertenbach

"The successful commercialization of a pressure oxidation (POX) process for recovering metal values, including gold, copper, zinc, nickel and molybdenum, is the result of a carefully planned development program. The initial task involves developing one or more conceptual flowsheets, including the POX autoclave and downstream purification and recovery steps. A laboratory program is completed to determine the technical viability of the flowsheets, define the operating parameters for each step and provide information for an initial economic assessment of the process. The process is then confirmed during a continuous pilot plant program, providing engineering design data and other information for the commercial design. A well-thought-out development program has been shown to be critical for reducing the risk of commercializing POX processes. Experiences developing POX processes for refractory gold ores and copper concentrates are briefly discussed. IntroductionPressure oxidation (POX) has become a common commercial operation for processing sulfide-bearing feedstocks. These feedstocks include gold ores and concentrates; copper concentrates; nickel concentrates and mattes; zinc concentrates; and molybdenum concentrates. Drivers for the development and commercialization of POX processes include:• The high cost for pyrometallurgical processing of sulfide ores, much of which is attributed to environmental controls.• The motivation to implement safe and more environmentally attractive alternatives for sulfide ores.• The need to process increasingly difficult ores with complex mineralogy.• Improvements made over the last 25 years in POX equipment design and experience operating commercial POX plants.Although the capital and operating costs for commercial POX processing can be high, this technology is capable of rapid oxidation of most sulfides and arsenic minerals in the feed, with little noxious gases and environmentally stable iron arsenate and other iron compounds in the POX residue (Marsden and House, 2006).In POX operations, sulfides are oxidized to either sulfates or elemental sulfur in an autoclave at elevated temperature and pressure with oxygen gas. An example is the overall oxidation reactions of chalcopyrite when sufficient oxygen is present, shown in the following reactions:"

Jan 1, 2016

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By Donald P. Tuchman, Emanuele G. Cauda, Steven E. Mischler, Elaine N. Rubinstein, Jay F. Colinet

The PDM3600 and PDM3700 are two closely related person-wearable dust monitors manufactured by Thermo Fisher Scientific. Both are based on tapered element oscillating microbalance technology and provide nearly real-time, mass-based readings of respirable dust concentrations. From a monitoring perspective, the primary difference between the models is the PDM3600 has an integrated cap lamp with attached inlet, while the PDM3700 has no cap lamp and a revised inlet attaches to the worker’s lapel. Using coals of varied origin and employing a wide range of concentrations, side-by-side measurements from these instruments were collected under controlled laboratory conditions and then compared. By use of ordinary least squares and weighted least squares regression methods, followed by mixed model analysis, results suggest there is no statistically significant or practical difference in instrument performance. The two monitors are equivalent for the field dust concentration measurements for which they were designed.

Feb 28, 2024

By Richard C. Holmquist

Some of you may be old enough to remember -- as I do -- the early days of World War II. A highly prepared, well-equipped Japanese striking force had moved like lightning across the South Pacific islands and Southeastern Asia. As the invasion force pushed its way down the Malaysian Peninsula, Singapore stood serene and beautiful, protected by its natural moat of water, busy as ever with its commercial pursuits. One can see its captains of trade and industry now, sitting com¬fortably on the veranda of the "Singapore Country Club", sipping scotch between cricket games, convinced that the weary, logistically extended Japanese force couldn&apos;t possibly cross over to their island which had been so secure for a hundred&apos; years or more. No need to remind you what happened. The brave men in their ships at sea and in the gun emplacements ashore were hopelessly out-gunned and out-maneuvered.

Jan 1, 1979

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project.