Search Documents

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By L. J. Altenburg

There are a lot of key factors involved in achieving a successful Safety Program. I would like to discuss some of these factors and how they have played a major part in our success at Jacobs Ranch Mine. The areas I will cover concern: 1) Facility Standards (Corporate/Minesite), 2) Communication (Employee/Management -"Teamwork"). 3) Proper Training (Employee/Management). 4) Employee Attitude. 5) Incentive Programs. 6) Health Programs. 7) Results/Benefits.

Jan 1, 1994

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By Keith Kern, Joseph P. Matoney, Kenneth E. Harrison

INTRODUCTION "When there is an economic need for cleaning fine coal to low ash, the technical difficulties will be solved. The utilization of fines below 28 mesh will determine the degree to which beneficiation will be carried. Whenever these "fines" will be processed into smokeless fuels or used as new materials for the chemical industry or for hydrogenation, a higher degree of cleaning will be economically justified”.(l) This quote from the 1943 edition of Coal Preparation correctly anticipates the use of fines as "smokeless" fuel or as a future component of boiler fuel and a1 so as a raw material for the chemical industry or possible new uses such as for internal combustion engines. Fines utilization depends upon an economic need and possibly neglects to say an environmental need or a government funded development program as the prime mover for development. In any event, this conference is faced with the "need" to beneficiate fine coal and undoubtedly among the processes that will be discussed are the unit processes of future coal preparation facilities. HISTORY OF DEVELOPMENT It is interesting to look at where we have been, where we are now and where we possibly will be in the future. In order to put some limitations on this presentation, we will for the most part confine our remarks to this century and particularly developments since World War II. We also will limit our remarks to the preparation of bituminous coals in the United States, and for the most part, to wet processes. In the 1943 edition of Coal Preparation, clues to the processes being used to beneficiate coal are contained in the Chapter Titles. An extensive treatment of "Hand Picking" was contained in Chapter 8. Chapter 7 contained a description of methods for "Preparation at the Face". Chapter 18 dealt with "Slurries, Sludges, Slimes and Water Treatment" and defined this size of coal as being the size at which "Jigs and Chance Cones are usually dispensed with and other methods such as the hydrator, tables, and froth flotation are employed. Generally the limit is 1.7mm to 3.4mm. In the days before World War I1 the then modern bituminous coal preparation plant contained jigs or Chance Cones for the coarse material +6.35mm, concentrating tables, launders or some classifier type of coal washer for the fines (6.35 x 0.15mm), and froth flotation as the only method of cleaning minus 0.15mm coal which was used very sparingly.

Jan 1, 1988

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By John Chapman, Daryl Hockley, Michael Paul, Silvia Jahn

As part of the waste characterisation program to address site reclamation, WISMUT GmbH initiated 56 columns operated as large-scale humidity cell tests. The columns were initiated to assess the acid generation characteristics of waste rock from 14 waste rock piles distributed around the site. Of the 56 tests, 11 are ongoing and have been operational in excess of 160 weeks. The results to date from these long-term tests are surnrnarised. In particular, the methods for, and importance of, establishing the availability of the carbonate neutralisation potential and acid generation potential respectively, are discussed. Geochemical controls on uranium, and the conformity between the geochemical models MINTEQA2 and EQ3/6 in assessing these controls are discussed. Testing indicates that waste rock with an MS-NP:AP ratio in excess of about 2.7 should result in net neutral pH conditions.

Jan 1, 2000

By A. B. Holland-Batt

Following a relatively static period in the 1960s and 1970s when incremental development rather than innovation was the norm for gravity separation, the last 15 years has seen a number of new developments in this area. The paper briefly reviews the traditional gravity separation techniques and then examines the newer developments such as centrifugal separators. Particular emphasis has been placed on novel devices or improvements that offer either better control or improved performance.

Jan 1, 1998

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By Jon Y. Kaneshiro, John S. Griffith, Anthony F. Stirbys, Mauricio Andrade

This paper presents an overview of the New Mississippi Tunnel Outfall for the Transportation Expansion Project (T-REX). The Outfall conveys highway and other urban drainage to the South Platte River as well as provides long needed relief from flooding problems in the southeastern portion of the Interstate 25 highway corridor. The Outfall tunnel incorporates a one-pass precast concrete segmented liner to convey storm water under I-25 then under Mississippi Avenue to the river. The Outfall crosses both the existing I-25 as well as the future improvements including under the Light Rail Transit, a new bridge abutment, widened lanes, and new retaining walls. The Outfall also crosses adjacent to several buildings and five bridges, under major traffic and utility intersections, and through difficult geology.

Jan 1, 2003

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By P. R. Busmann, D. J. Rogers

The Bureau of Reclamation's Syar Tunnel project included excavation of a 9.2 kilometer (5.7 mile) long, 3.6 meter (11.8 ft) diameter tunnel through gently dipping sedimentary rocks consisting of shales, siltstones, sandstones and limestone. The tunnel was supported full length with precast concrete invert segments and lightweight steel sets and lagging. Several world records for advance rate were set, including 57 meters (187 ft) in an eight hour shift and 127 meters (417 ft) in a 24 hour day. The tunneling system utilized a remanufactured and modified Robbins hardrock TBM and a 9,280 meter (30,450 ft) long, 61 centimeter (24 inch) wide, continuous conveyor system.

Jan 1, 1991

By G. Barelli, C. Giusti, W. H. Langer

Natural aggregate – sand, gravel, and crushed stone – is the number one non-energy mineral resource in the world in terms of both volume and value. A plan for the sustainable development of aggregate resources can include: 1) policies and economic incentives to encourage identification and protection of potential resources, 2)efficient quarrying and processing of aggregate, 3) efficient use of primary aggregates, 4) greater use of recycled, waste, or substitute material, 5) inclusion of costs of all environmental impacts in price of material, 6) reclamation to beneficial secondary uses, and 7)identification of objectives, targets, actions, and sustainability indicators. Quarrying can also contribute to sustainable ecosystems through natural habitat reclamation.

Jan 1, 2003

By Brad Hewitt

Since Campbell Mine began processing ore, there has been a gravity gold recovery circuit. From 1947 to 1982, gravity gold was concentrated through the combination of jigs and mercury amalgamation. In 1982, jigs with concentrating table upgrading commenced and was utilized until the end of 1994. As of January of 1995 to the present, Knelson Concentrators in com­bination with concentrating tables have been employed to achieve a refinable product. An evaluation of the justification used for the last change is the focus of this paper.

Jan 1, 1996

By Fathi Habashi

THE UNIT process of adsorption involves two steps: 1) Loading of the adsorbent. 2) Recovery of metal values from the adsorbent. Charcoal is the adsorbent commonly used in extractive metallurgy. The discovery of the adsorptive power of charcoal from solutions is generally accredited to Lowitz (1785), who observed that several dissolved organic substances were precipitated on charcoal. Graham was the first to demonstrate that inorganic substances were also adsorbed on charcoal. In 1830, he reported that iodine dissolved in KI solution was adsorbed on charcoal. Also calcium ions were adsorbed from limewater, as were lead ions from lead nitrate solution. The use of charcoal in metallurgy was first applied

Jan 1, 1970

By G. E. Jones, G. K. Hoffman

Two Sun Juan Basin studies were completed through the USGS National Coal Availability program. The study areas are in the northwest Bisti field (Fruitland Formation) and in the eastern Standing Rock field (Menefee Formation). In the Bisti and Standing Rock areas, the original coal resource5 are estimated at 4.66 and 3.1 7 Gt (5.14 and 3.49 billion st), respectively. The Bisti coal resources are greatly reduced by the Bisti-De-Nu- Zin wilderness area, which contains an estimated 1.13 Gt (1.25 billion st) of coal. Technological restrictions remove 32.5% from Standing Rock's original resource. Available resources are 60%. 2.79 Gt (3.07 billion st), of the Bisti original resource and 65%, 2.07 Gt (2.28 billion st), of the original Standing Rock resource.

Jan 1, 2002

The Janet Annenberg Hooker Hall of Geology, Gems and Minerals, located in the National Museum of Natural History, Smithsonian Institution, in Washington DC, opened in September, nine years after initial fundraising efforts were begun. The 1,858-m2 (20,000-sq ft), $16-million hall was mostly funded by private groups and individuals, including $1.7 million from 43 National Mining Associa¬tion (NMA) member companies. Companies that contributed more than $100,000 included Cyprus Amax, Phelps Dodge, Asarco, Homestake Mining, BHP, Caterpillar, Cleveland Cliffs, Exxon Coal and Minerals, Freeport-McMoRan, Newmont Mining and Peabody Holdings. The mining industry's contributions funded a walk-through Mine Gallery. It. features diora¬mas of four mines, as well as numerous specimens associated with the mines. The Mine Gal¬lery demonstrates to the public the importance of mining. The hall was named in honor of Hooker. She contributed $5 million in cash plus the Hooker Yellow Starburst Diamonds to the project. The hall is touted by the Smithsonian as the "most comprehensive earth science complex of its kind." It consists of seven galleries, each devoted to different aspects of gems, minerals and rocks. In addition to the Mine Gal¬lery, the hall contains a collection of gemstones and jewelry pieces, an extensive collection of minerals, a gallery devoted to plate tectonics and a gallery devoted to the moon, meteorites and the solar system. The new hall is a complete makeover of the old and outdated Geology Hall. It was built in the 1960s and finally closed to the public in 1995.

Jan 1, 1997