Search Documents

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

By Xintan Chang

A computer software package, named CFIRE, for the general ventilation network analysis and fire control, mine fire and/or coal spontaneous combustion, has been developed at Xian Mining Institute in China. It is a multipurpose package with adequate capacities of ventilation map drawing, ventilation network analysis, gob fire simulation, steady state ventilation simulation and transient state ventilation simulation. It was written in a user-friendly style, driven by menus, facilitated by on-screen messages and supported by the allowance of user interferences. CFIRE has used up-to-date research findings focussing on the practical needs of coal mines. This paper discusses briefly also the relevant theoretical principles on which this package has been perceived.

Jan 1, 1989

By M. Bidart, V. Sawyer, M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas that are below the natural groundwater elevations. This necessitates dewatering, which requires a method for the disposal of the extracted water. Some of these open pits extend well below, the water table with dewatering volumes greater than 10,000 gpm (38,000 L/min). Some mines with large volumes of dewatering water have constructed reinfiltration basins to reintroduce the water into the groundwater system at a point some distance from the pits. This paper presents an overview of the state of the art of reinfiltration projects, including the permit process for such projects in Nevada. The paper includes the necessary engineering considerations.

Jan 1, 1997

By J. B. Fletcher

Miami Copper Company has used conveyor belts underground since 1947, At that time, the draw level for a portion of the orebody was only 25 feet above the haulage level To get the main haulage drifts as far away as practical from under the stoping area, 301, belt conveyors were used for lateral transfer, If the haulage drift was kept in good ground., a satisfactory draw of these stopes could be effected in that repairs to the conveyor drifts could be accomplished while drawing ore from the stopes. Some 7,400,000 tons of ore were mined with the 301d belt conveyor at a belt cost of approximately $0,004 per ton of ore. When the mining plan for a new section of the mine was laid. out in 1953, it was decided to use belts to collect the ore from the higher draw levels, and. move the ore laterally to centrally located concrete ore passes for transfer to the main haulage level (See Cut #1), The final plans used belt conveyors too collect from 3 stopes: on the 570 level, 2 stopes on the 720 level, and one stope on the 900 level. The six stopes to be mined in this manner would produce about 8 million tons of ore, and the sequence of mining was such that not more than four 400 feet conveyors would be in use at one time, Four conveyors using 36 inch, 4 ply belting were designed by the mine engineering office and fabricated at the mine shop, so that no piece was longer than 10 feet, and. the heaviest piece was the 25 horsepower motor, The head drive section, and the tail-pulley-takeup section were of bolted construction so they could be broken down for easing moving, Due to the size of the mine openings, the belt had to be transported into the mine in 400 feet rolls, requiring two splices for an installed belt. A torque arm speed reducer was used with a V -belt drive which made it possible to change the speed of the conveyor by changing the diameter of the V-belt pulley (See Cut #2).

Jan 1, 1958

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved

Jan 1, 1997

By Joseph E. Worthington

The Haile Gold Mine is one of the earliest gold discoveries in the eastern United States as well as one of the largest gold producers from that region. Gold was first discovered in the gravels of what is now known as Haile Gold Mine Branch in 1828 on lands then owned by Colonel Benjamin Hale (spelling not the same). Small placer workings were immediately started and it was not long before the surrounding residual soils and saprolites were also found to contain gold. Following the presence of gold in the residuum eventually lead to the discovery of the underlying gold-bearing lodes that actually outcropped in saprolite form where not masked by heavy vegetation or a thin veneer of Coastal Plain sand. The earliest attempts at production, immediately after discovery, utilized slave labor, washing gravel and residuum from leased tracts that were 15m (50 ft) square. Several at- tempts at small milling operations were made during the en- suing decades, but there was really no substantial or successful production until the 1880s.

Jan 1, 1990

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

By Viktor Tokle, C. W. Dawson

The Devico directional core drilling system and its capabilities are described, with reference to other directional drilling technologies and the advantages and disadvantages of these systems. The advantages and disadvantages of a number of borehole navigation systems are also presented. A discussion of the applications of the technology follows, illustrated by case histories. Finally, the environmental impacts and benefits of the technology, in comparison to more conventional systems, are presented.

Jan 1, 1999

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By H. V. Fairbanks

The following processes were investigated using ultrasonic treatment in mineral recovery: (1) cleaning coal from coal slurry ponds, and (2) extracting precious metals from tailings and other sources. The treatment entails the production of a water slurry of the material containing the mineral which is made to flow over the vibrating surface of the ultrasonic treatment unit. The vibrations transmitted into the slurry break up particle agglomerates and also produce a scrubbing action on the surfaces of the particles. The treated mineral particles were found to have increased settling rates, better compaction, and more rapid water drainage.

Jan 1, 1990

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By David G. Hammond

INTRODUCTION Previous papers and discussions at this conference have already covered the subjects of identification and nature of risks, allocation of risks and contractual arrangements. In this portion of the conference, in the light of topics already covered, we will consider how to minimize risks and how to mitigate losses. Webster defines mitigate as "to make less severe or painful", an apt definition for our purpose! RISK MANAGEMENT POLICY The first thing that must be said about risks, especially in construction, is that they exist and that they don't necessarily fall alike on the just and the unjust. Some risks, i.e., some kinds of risks, must be recognized as inevitable in engineering and construction and therefore must philosophically and realistically be accepted as part of situations to be dealt with. Dealing with means minimizing, covering, and sharing of risks and doesn't mean merely passing off the risks to someone else. While some risks can be avoided, for example, whether the structure will fall down or the excavation will cave in, risks management primarily deals with: A. minimizing risks---whomever risk it may be B. equitable sharing of those risks among the participants.

Jan 1, 1979

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By J. W. Mausteller

Chemical oxygen supplies have been used for nearly 60 years, with their greatest application during the last 25 years. They are of two types, the superoxides and chlorate "candles", The superoxides are demand chemicals, responding to the needs of the user and to supply oxygen and remove carbon dioxide. Chlorate candles are formed solid element which furnish oxygen only and do not remove carbon dioxide. Properties of these materials will be described, with comments on the respiratory requirements of a man under various workloads, types of equipment which use chemical oxygen, comparison with other systems and potential application to an underground mine survival system.

Jan 1, 1971

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987