Search Documents

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By J. A. Jirestig

Laboratory investigations on the possibility for magnetic separation of sulphide minerals are reported. A survey of several sulphide ores and flotation concentrates shows that magnetic separation in most cases is not a suitable primary method of beneficiation. However encouraging results have been obtained in concentrate purification. At the Boliden complex sulphide ore concentrator in Garpenberg a Allis-SALA MK III carousel High Gradient Magnetic Separator (HGMS) is used together with a small flotation circuit to recover sphalerite lost to the galena concentrate in lead flotation. The result after four years of refining the HGMS process, show increasing zinc recovery and enhanced quality of the lead concentrate.

Jan 1, 1993

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

By L. L. Damon

A geochemical study of cyanide neutralization processes was conducted at Brohm Mining Corporation to gain a better understanding of the leach pad behavior and to develop a simplified procedure to quantify the attainment of compliance with permitted cyanide neutralization criteria. Such attainment is a prerequisite for off-loading spent ore from the leach pad at the "load/unload" gold heap leach operation. The geochemical study program consisted of size fraction analyses and weak acid dissociable (wad) cyanide analyses for various sections of the spent ore from the actual leach pad. Further testwork included size fraction analyses and wad cyanide analyses on the ore from four 29 foot laboratory test columns which were leached and neutralized with different neutralization treatments in parallel with an actual active leach pad. Wad cyanide was analyzed daily on the neutralizing columns and various parameters were monitored weekly on the influents and effluents during the leach cycle and neutralization period. A comparison was made of neutralized effluent chemistry and porewater extraction fluids, as well as an analysis of the selective adsorption of cyanide on various particle size fractions.

Jan 1, 1992

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By Ronald A. Crowson

Detailed stratigraphic studies of the overburden at North Carolina Phosphate Corporation new South Creek Mine have delineated several aquifers and acquicludes within the 30-meter-thick overburden section of late Pleistocene sands and clayey sands. A major aquifer occurs in the 10-meter-thick sequence of shelly sands of the early Pleistocene Croatan Formation. The water-charged Croatan sands thicken into a paleodrainage surface on top of the Pliocene Yorktown Formation, a major aquiclude. A three-phase dewatering program is projected: 1) improve surface drainage around mine perimeter to reduce both flowage into the pit and rainfall recharge; 2) use a wellpoint system to dewater the upper 8 meters; and 3) use recharge wells along the axis of the paleo- drainage to dewater the overburden below 8 meters.

Jan 1, 1983

By J. C. Purcupile

In this time of increased coal demand, a faster and safer method for roof support is needed. This report outlines the preparation and testing of a machine which we feel will help answer this need. The results of the tests are encouraging, and indicate that further exploration of the method should be continued.

Jan 1, 1975

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

By K. Peri

The leaching behavior of gold in ammonical solutions with iodine as an oxidant has been investigated using cyclic voltammogram and Tafel polarization. The majority of experiments was carried out at 75°C and the results were compared with the equilibrium consideration on the iodine-ammonia system. The distribution of nine iodide containing species at various pH values in the absence and presence of ammonia was considered at three different temperatures. It was found that by introduction of ammonia into the system, the concentration of iodide (r), iodine (12) and triiodide (13') is increased substantially which in turn helps the rate of dissolution of gold. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical controlled mechanism.

Jan 1, 1999

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. In this paper we will review technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. INTRODUCTION Portable mine refuge chambers are used in US coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity within the shelter, as well as the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter, 23 humans, and also includes the surrounding mine environment. The thermal simulations were performed using ThermoAnalytics' validated commercial heat transfer prediction code, TAITherm (v12.0). Additionally, TAITherm's Human Thermal Module (HTM) provided the capability to simultaneously model the thermo-physiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and also provided a core temperature response prediction, which can be used to evaluate survivability in heat stress situations [1]."

Jan 1, 2016

By John C. Cook

There is pressing need for better means of exploring ground conditions ahead of mining. Exploration drilling has the drawbacks of high cost and a seriously restricted sampling zone. Traditional geophysical exploration methods including gravity, magnetic and resistivity techniques have been used with some success underground, but all give poor target delineation relative to range, since they depend upon minor distortions of a potential force field. Much greater ratios of resolution to range can, in principle, be obtained by employing electromagnetic or seismic radiation as the exploring agent. This is because propagation time delays can be used to measure range accurately, and to separate the small effect of a distant target from the much larger effects of nearer targets and of the transmitter. Seismic waves have long been used with great success in exploration for petroleum, and recent research on their application underground is promising. Electromagnetic (radar) waves have been very successfully used for detection and location through the air and outer space, and have also explored through polar icecaps more than a mile thick.l It is not generally realized that below the soil many rocks are also somewhat radar-transparent, and that radar can be used for exploring such rocks, once a quarry, a mine, a borehole, or other means of access has been opened. Radar waves are reflected by any boundary or object where they encounter a large change in electrical properties.2 The usual cause of such a change is a difference in moisture content. Radar waves passing

Jan 1, 1972

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By Bruce A. McKinstry

Introduction For many major mining projects the time frame from initial planning to production can be measured in decades. Hecla's Silver Shaft project, scheduled to go into production by the end of this year, includes a complete surface facility, shaft with an ultimate depth of 2.4 km (7,700 ft), complete ore pass and loading pocket system, and 610 m (2,000 ft) of development drifting and stope preparation. The project was conceived in the fall of 1979, and the duration of a mere four years from conceptual engineering to production is testimony to what can be accomplished when a mining company and a contractor work as a team rather than developing into two warring camps, as often happens. Engineering In 1979, Hecla Mining Co. awarded a contract to J. S. Redpath Corp. to perform feasibility investigations and design engineering related to a proposed new shaft facility at the Lucky Friday Mine. The Lucky Friday, in Mullan, ID, is a major producer of silver, as well as significant quantities of lead and some zinc. In late 1979, stoping was in prog-

Jan 10, 1983

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967