Search Documents

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By John C. Ferm

The role of geology in coal exploration, mine planning and mine development has, in the past, been relatively small. The primary reason for this lies in. the simplicity of geologic concepts that were necessary to bring these operations about. These concepts can be briefly stated as follows: 1) coal occurs in the beds or layers and is overlain and underlain by shales, sandstone or limestone in varying porportions, 2) each coal bed has been given a name and certain quality characteristics can often be associated with a named bed and 3) coal beds (and their adjoining rocks) are often folded into broad anticlines or synclines and, in some places, displaced or faulted. In actual practice, however, these simple principles have been found wanting. Thickening, thinning, pinch outs or changes in coal quality occurred but the occurrence was apparently unpredictable and the only real solution to such problems seemed to be practice and experience. This combined with ingeneous engineering solutions have provided answers to most questions. Perhaps a more fundamental reason that geology could offer so little input to coal mining is that the thickest, most persistant and best quality coal seams followed the above stated rules fairly well. In many areas, however, such seams are now nearing exhaustion and the increased demand for clean, non-polluting, safe energy is quickly bringing a need for techniques of exploration and mining procedures that will make development of formerly unminable seams a profitable venture. For the past 20 years some considerable body of knowledge has been added to the framework of the geology of sedimentary rocks and it is the purpose of this paper to present some of these newer ideas that will be useful in solving some of the present problems of coal exploration and development.

Jan 1, 1976

By D. E. Hinkle

Past surface-mining operations in Appalachia primarily followed mountain con-tours. It is estimated that about 18,000 mi. of highwalls are exposed throughout Appalachia. An evaluation procedure for determining the secondary mining potential (SMP) of these highwalls has been proposed. Sixteen parameters affecting the SMP were isolated. These are grouped in four major categories: geologic conditions, existing infrastructure, site conditions, and environmental conditions. The parameters were then ranked by their impact on SMP and assigned weighting factors. A simple mathematical procedure yields an SMP number (0 < SMP < 100), which may then be used to compare alternative sites and technologies. Determination of limits and ranges while grouping data was aided by field visits to over 40 exposed highwalls in Eastern Kentucky. An interactive program has been developed to rapidly evaluate the SMP for pre-mined sites. The mathematical procedure estimates the relative potential (i.e., techno-logical feasibility) for remining for three predominant secondary mining methods: augering, Hi-wall mining, and underground mining. Other secondary mining methods are briefly reviewed and compared.

Jan 1, 1989

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By Eric K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. However, previous models have tended toward being either data-intensive and deterministic, or data-limited and highly stochastic. The need for a fully integrated package with a simplified user interface has never been more apparent. In this paper, the design of a surface mining simulation model documented in Albert (1986) is described. The basic features of the surface mining system and their counterparts in the simulation model are discussed. The methods and algorithms used to implement these subsystems are presented. Considerations of information management and software design are illustrated, especially as they apply to the application of the package by a mining engineer. An example is provided to demonstrate the concepts embodied in the model and to show how a surface mine is simulated from mine parameters.

Jan 1, 1989

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes&apos; Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900&apos;s to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company&apos;s success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By William E. Bonini

Gravitational field anomalies have been observed over many igneous intrusives of medium (4000 km2) to small (100 km2) size in outcrop area. These studies give good results because the residual anomalies can be separated from larger scale crustal anomalies and density contrasts usually are present. Although unique solutions are not possible, the analysis of the gravity anomalies can put limits upon the geologic interpretation of such bodies. Three examples in Montana, U. S. A. are discussed: (1) the Boulder Batholith, a late Cretaceous quartz monzonite series of intrusives of 4000 km2 outcrop area; (2) the Little Rocky Mountains, an up-domed area, in which an Eocene porphyry (130 km2) has intruded the Precambrian crystallines and lower Cambrian sediments; and (3) the Crazy Mountains, an Eocene diorite (100 km2), which has intruded the Paleozoic and Mesozoic sediments. In both the Boulder Batholith and the Little Rocky Mountains, intrusive rocks are less dense than the surrounding rocks and negative anomalies are found (40 and 28 mgal, resp.). In the Crazy Mountains, the intrusive is more dense than the surrounding sediments and a sharp positive residual anomaly of 42 mgal is observed. The analyses of the gravity anomalies predict that: (1) the thickness of the Boulder Batholith is on the order of 10 to 15 kms and is concave upward; (2) the Little Rocky Mountain syenite is not a simple laccolith, but is T-shaped and extends in depth to about 16 kms; (3) the Crazy Mountain diorite is not a simple small scale series of stocks, but a large connected body extending in depth 5 kms to the basement (although nothing can be said of it within the basement because there is little density contrast). The analyses of the anomalies place important limits on both the areal and depth extent of the intrusive bodies. Of all possible geophysical techniques, gravity studies offer the most promise in the determination of the shape in depth of intrusive bodies.

Jan 1, 1969

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a &apos;sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997