Search Documents

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

By John Mastoris, Shkurta Gashi, Kostis Dragasakis, Kostas Kouklidis, Halil Berisha

Water is increasingly recognized as a critical issue for sustainable development, becoming as important as carbon to corporate responsibility and reputation. Although the cement industry’s overall ‘water footprint’ is relatively small compared to other sectors, the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD/CSI) has recognized the importance of water and the need to take actions towards efficient water management, with developing standardizing practices and employing a risk-based assessment approach, mostly at local level where individual facilities and activities can have implications for other water users in the area. Sharrcem, a member of the Titan Cement Group, has made significant investments to upgrade its production facilities, the technological process and apply environmentally friendly technologies. Under this frame, Sharrcem implemented a project for the construction of a Waste Water Treatment Plant (WWTP) in the Cement Plant facilities, which has been successfully operating since early 2016. This paper discusses the technology applied at the new WWTP and the results achieved already, with significant improvement in the quality of the treated water, as compared to the previous situation where untreated wastewater was directly discharged to the nearby Dimce Stream. The WWTP project is a major investment of Sharrcem that aims to improve the quality of the discharged water effluents and thus prevent potential river pollution and overall protect the environment and the health of Sharrcem employees and local community. The WWTP operates with the Sequencing Batch Reactors (SBR) technology, is fully automated and has been also connected with few households of the neighboring community to treat also their sewage water. The plant can be expanded in the future – to connect with additional households - without increasing the size of the treatment tanks. One of the benefits of this project is that by removing a variety of contaminants from water it becomes usable again, depending on the nature of the contaminants and the end use of the water treated. According to the monitoring results the treated water that comes out of the WWTP fully meets quality requirements according to the EU and local limit values standards

Jan 1, 2017

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By Frank A. Jerabek

Pneumatic stowing was first introduced in longwall mining in the middle twenties. Since that time it has advanced through many stages of development, particularly abroad, which have greatly improved its efficiency and contributed to its growing use. Pneumatic stowing originated in coal mining but has also been adopted in metal mining. This paper discusses the techniques of pneumatic conveying of. stowing material and equipment and applications of pneumatic stowing.

Jan 1, 1966

By Robert W. Holliday

Natural resources are the reservoir from which society draws its material sustenance. Although there is a growing awareness of the need for aesthetic resources such as space for recreation and natural beauty, the basic resources are soil, air, water, and minerals including fuel. Minera's and all sources of energy gain in relative importance with advancing technology and expanding industrilization. In the highly industrialized economy of the United States, almost every aspect of man's life is touched in some way by a product of, the mineral; industries. Agriculture owes much of its productivity to mineral-based fertilizers, insecticides, and mechanical equipment. Modern construction, manufacturing, communications, and transportation are all dependent on nonmetallic minerals, metals, and fuels. Throughout history, those nations with access to minerals, and the technology for using them, have gained ascendency. Before World War II the leading powers also were, leading coal producers. In order of declining rank the five leading' coal producers were the United States, the United Kingdom, Germany, the USSR, and Japan. That the military victory went to the side with the greater' capacity to convert iron and coal into tools of industry, and weapons, is' more than coincidence. It is a fundamental' fact of existence. It is axiomatic that the United States must have a continually increasing supply of minerals if we are to meet the needs of our burgeoning population for a comfortable standard of living and for national security.

Jan 1, 1968

By Clayton J. Parr, Northcutt Ely

Mining law is essentially a branch of the law of real property. It concerns acquisition of property for extracting contained minerals, and the rights, privileges and duties that fall upon the holder thereof once the rights are acquired Accordingly, this section focuses on the procedures to be followed in acquiring state. federal and private lands, and defines briefly the nature of the rights obtained. The mining laws of Canada and Mexico are summarized, and the related subjects of minerals taxation and governmental regulation are discussed briefly. This section is not intended to be the basis for legal decisions. Rather, its purpose is to provide the engineer with an understanding of basic principles and procedures. For a detailed treatise of mining law, reference can be made to The American Law o] Mining, a five-volume set edited by the Rocky Mountain Mineral Law Foundation. The law changes constantly, especially that based on federal and state statutes, and the reader is cautioned to be alert for subsequent modifications of statutes, regulations and case law. 2.1-PRELIMINARY LAND-STATUS CHECK Often, after completion of area reconnaissance, or perhaps after receipt of a submittal, a specific more localized target area will become of interest. Usually, an intensive exploration program comprising detailed surface mapping, sampling, geophysical prospecting and drilling will be required before the mineral potential of the ground can be properly evaluated. Before an investment of this magnitude is made, however, it is advisable to obtain rights to mine ore from the property. Otherwise, knowledge of the exploration activity might greatly inflate land values, or speculators or competing mining concerns might step in. Hence, as a general rule, a land-acquisition program should be undertaken before an intensive exploration project is begun. The first step in such a program is to make a land-status check to determine whether the subject lands are available and, if so, from whom they can be obtained and by what means. 2.1.1-BUREAU OF LAND MANAGEMENT RECORDS In those states which contain large areas of federal land, basically (he western states, the primary informational source is the records of the Bureau of Land Management. These may t)e examined at the land office having jurisdiction over federal lands in the area of interest. The records for Montana and North and South Dakota are kept at the Billings (Mont ) land office; Wyoming, Nebraska and Kansas, Cliejenne, Wyo.; New Mexico, Oklahoma and Texas, Santa Fe, N M ; northern Alaska, Fairbanks, and southern, Anchorage; Utah, Salt Lake City; Nevada, Reno; Arizona, Phoenix; Colorado, Denver. There are two land offices in California, at Sacramento and Los Angeles Records for other states are kept in Washington, D C. at the office of the Director, Bureau of Land Management.

Jan 1, 1973

By Egon Pohl, Peter Eckl, Friedrich Steinhäusler, Johanna Pohl-Rüling

RADON EXPOSURE AND CARCINOGENIC CELL TRANSFORMATION The highest radiation burden to miners is due to inhalation of radon and its short-lived decay products. The quantification of the risk associated with this radiation burden is complicated by modeldependent lung dosimetry, insufficient accuracy of past human exposure data as well as lacking knowledge about potential synergism of various carcinogens. Nevertheless, it is evident from epidemiological studies of miners that inhalation of elevated levels of radon daughters is correlated with increased lung cancer incidence (UNSCEAR, 1977). The situation is further complicated by the lack of reliable data on the biological variability of the latency period for the development of lung tumor under varying exposure conditions. At present information on variation with age is scarce, however, it is indicated that the excess lung cancer rate for workers exposed to high radon levels is considerably higher, if exposure occurs at ages over 40 years as compared to under 30 years of age (Sevc, Kunz, Placek, 1976). Furthermore, latency period is shorter by 6 - 7 years for smokers exposed to elevated radon levels than for non-smokers (Fry, 1976). Analysis of US- and CSR-uranium miner data revealed that the mean latency period is in the order of about 15 years (Jacobi, 1973). These uncertainties, together with medical diagnostic shortcomings, lead to the dissatisfying situation that at present the detection of radon induced injury of mining personal is primarily the assessment of the endpoint, i.e. radiation induced cancerous transformation of lung cells with typically less than 10% chance for recovery. Therefore it would be advantageous to develop practically applicable diagnostic aids to indicate already early precancerogenic changes of cell characteristics. This would permit the identification of specific population groups at increased risk for the development of lung cancer, thereby increasing the chances of more successful medical treatment. Despite continuous improvements in the reliability of test methods for the diagnosis of cancer cells there is still need for techniques, which enable the detection of transformed cells before the onset of invasion of the host organism. It is generally recognized that the transformation of a cell into a malignant state leads to a change of the cell surface, indicating a correlation between membrane-specific immunological properties and loss of growth control. Surface alterations on cells appear to be responsible in part for the malignant state and are not simply secondary effects of the transformation (Schnebli and Burger, 1973). Furthermore, membranes of cancer cells differ significantly from those of normal cells, particularly, in permeability properties (Rastogi, 1976). In dying cells, proteins, glycoproteins, peptides, aminoacids and their breakdown products are released, which block the permeation of the membrane itself. A mammalian cell can be considered as a 3-phase system (interior, boundary, environment) with the membrane forming a heterogeneous barrier between two subsystems. Under normal circumstances a difference of chemical potential is maintained on both sides of the membrane, causing an ion gradient across and fixed surface charges on the membrane. This results in a membrane resting potential (MRP) between cytoplasm and the bulk medium. It has been shown that MRP is a highly sensitive indicator for cellular reactions due to physical, chemical and biological agents, particularly whenever phenomena of transport and ion gradients as well as permeability are involved (Redmann, 1980). The primary interaction of the agent "ionizing radiation" with any form of living matter occurs at the cellular level. The component with the highest hit probability is the cell membrane. In the study presented MRP-changes of human cells were investigated with simultaneous measurements during irradiation and post-irradiation intervals up to six days. Furthermore, the suitability of MRP-measurements of human cells was tested as an indicator for early changes of cellular properties prior to the histological confirmation of carcinogenic transformation. EXPERIMENTAL METHODS Lung cells The biological specimen used were cultured human lung cells and human lung biopsy samples. Monolayers of lung fibroblasts (W138) were grown in petridishes using conventional culture techniques. In addition, transformed lung cells (W138SV13, subline 2RA) were used applying similar culture methods. All petridishes were incubated at 37°C and only cells in logarithmic growth phase were used. Freshly excised lung biopsy samples were obtained from randomly selected male and female patients (20 cases), where suspected or unclear malignancies were indicated by clinical or X-ray observations. At the time of sampling 80 % of the patients were or had been smokers in the past. The samples were taken by means of a stiff bronchoscope introduced into the trachea under local anasthesia with 1 % Novesinsolution (preparation with Atropin and Pantopen). This permitted the observation of both main bronchi down to the segmental bronchials. From each patient two tissue samples were excised from the mucusepithelial layer under visual control with fiber optics and transferred immediately into 1 % NaClsolution. One sample was taken from the suspected

Jan 1, 1981

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By Robert L. Randall

The mineral industries have a continuing need for market forecasting and analysis for a variety of purposes, among which are organization and control of the sales effort, financial and corporate planning, and evaluation of the anticipated revenue from investment in proposed projects. For anything beyond the simplest extrapolation, some kind of economic reasoning or analysis is called for, which may or may not be incorporated into a formal or quantitative model. The principles described here apply to most of the commercially significant minerals and metals. The examples are drawn largely from the copper market, as it is the one with which I have the most practical experience. Practical forecasting is the process of analysis and synthesis from three categories of knowledge: facts and statistics, theory, and practical knowledge and informed opinion. Although many attempts have been made to build forecasts on only one of these three pillars, none has been successful as an operating procedure because of the lack of balance. There are no facts about the future-only about the present and the past. Facts can illuminate the future, but the future can be described only in terms of probability or more or less likely states of affairs-not as a continuous extension of the past and present. Likewise, theory, although useful as an organizing discipline and for providing a methodology of analysis, is inadequate for the complexities of reality. This is especially so when there is feedback between plans and forecasts to produce a new outcome and when there are significant elements of unpredictable free will, such as presidential jawboning or foreign policy considerations. Such elements are difficult to accommodate in neat theories, although they must certainly be reflected in the forecasts. Pure opinion frequently suffers from both a lack of-disciplined reasoning and the presence of biases or self-interest. While the future is unknown, it tends to cast its shadow before it; hence, forecasting is the art and science of positioning oneself so that the shadow becomes visible to the forecaster.

Jan 1, 1979

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By D. F. Strong

Most Newfoundland. mineral deposits can be clearly classified as within rocks formed either as accreting plate margins (ophiolitic pyrite-chalcopyrite massive sulfides such as Betts Cove, Whalesback, York Harbour, chromite at Lewis Hills, and asbestos at Baie Verte), at consuming plate margins (Kuroko-type polymetallic massive sulfides such as Buchans and Pilleys Island, porphyry-type Mo-Cu at Rencontre, fluorite at St. Lawrence), or within plates (zinc deposits at Daniels Harbour, sedimentary iron ores at Wabana, manganese in Conception Bay.) As these metallogenic patterns can be convincingly extrapolated southward into the Appalachians and northward to the Caledonides, they provide an important means of eliminating and selecting areas for particular exploration targets. Sonic criteria are described for the recognition of these environments of differing economic potential.

Jan 1, 1973

By M. P. A. Hames, D. R. Beaumont

INTRODUCTION Legend has it that when Isembard Kingdom Brunel was confronted with the cost and consequences of one of his bridges having failed, he responded cheerfully that the event had saved investors and taxpayers a fortune because it prevented him from repeating the same design at several other locations. To meet the demands of rejuvenating and expanding the transportation system in an era of industrial growth Brunel and his contemporaries introduced bold designs and many innovations. Great advances in design and construction techniques resulted, yet these too had their practical limits as the story tells. In the gold mining industry today we face the same challenge of expansion, yet designers must respond mindful of economic restraints. Is innovation the answer? It has two meanings; to bring in novelties and to make changes. Distinguishing between improvement and novelties, or simply recognizing the benefits and limitations of new ideas over proven technology is part of good design. This paper will illustrate the practical aspects of selecting appropriate solutions to a design problem by examining a variety of examples common throughout the industry. Since a variety of engineering disciplines contribute to the design of a gold processing plant, and each has some old wisdom to impart or new development to boast this paper is divided into the different areas of expertise involved.

Jan 1, 1987

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what's ahead.

Jan 1, 1983

By S. S. Peng

This paper presents a computer program package for predicting surface movement and deformation caused by under-ground coal extractions. It is capable of: predicting final surface movement and deformation over underground openings; predicting dynamic surface movement and deformation process associated with underground lingual mining operations; processing and bookkeeping subsidence survey data; recommending subsidence parameters for those new coal mines where no subsidence data are available; and deducting subsidence parameters from collected subsidence data.

Jan 1, 1986

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999