Search Documents

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By Haydn H. Murray

The area from Ohio on the east, Tennessee on the south, and Minnesota on the west: contains some very unique and useful clay deposits. Included are fireclays and plastic clays in Ohio, Kentucky, Indiana, Illinois, and Missouri; flint clays in Kentucky and Missouri; ball clays in Kentuckv and Tennessee; adsorbent clays (fuller's earth) in Missouri, southern Illinois, and Tennessee; and alluvial clays and shales for structural clay products from every state. Unique kaolin clays are known in Minnesota, Missouri, and southern Illinois and halloy-site localities are known in southern Indiana. The geology, physical properties, and uses or potential uses of these midwestern clays are described.

Jan 1, 1980

By J. Kang

Supercritical fluid extraction (SFE) has became an attractive alternative technology to be a new process to recover metal, of which can be substitute the existing Leaching/Solvent extraction processes. Solvent extraction of metallic ions is a technically important and also well-established process that is used in the chemical and hydrometallurgical industries.1 Solvent extraction techniques use the chelation of metallic ions dissolved in liquid solution with organic ligands. Conventional solvent-extraction technique needs large amount of organic solvents and often creates environmental problems.2 More environment-friendly technology is needed nowadays, and there have been increasing attentions to extract metal ions by SFE. CO2 becomes one of the most notable alternative organic solvents due to its nonflammable, nontoxic, nonpolluting, and relatively inexpensive properties with its moderate critical point (73.8 bar, 31.06 °C). Many works have been reported in metal extraction under the supercritical CO2 (scCO2) solvent.3-5 In this study, to recover cobalt from wastes especially from spent lithium ion battery scrap, we selected two ligands ? Cyanex 272 and DEA (diethylamine) for the metal extraction in scCO2. Cyanex 272 is a commercially available extractant along with its series, Cyanex 301 and Cyanex 302. Smart and coauthors measured the metal extracting abilities of these three extractants, and found that Cyanex 301 and Cyanex 302 extracted metal ions much better than Cyanex 272 in the scCO2 solvent.10 The pH of water contacted with high pressure CO2 (70-200 bar, 25-70 oC) is about 2.8-2.95 based on the calculation and the measurement.6-7 Cyanex 272 is known to be less effective as a metal extractant in this low pH environment compared with other Cyanex series. However, when DEA is added to metal extraction reaction with Cyanex-272, DEA works as a strong base to Cyanex 272 converting Cyanex 272 to a deprotonated form (Figure 1), which results in an easy formation of metal complex and the enhanced extraction rate of metal ion.8 Therefore, the purpose of this paper is the metal extraction from spent lithium ion battery waste using scCO2 with Cyanex 272 and DEA.

Jan 1, 2010

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By Shane Yanagisawa

The Mineral Creek Diversion Project is at the Asarco Ray Mine Complex, about128 km (80 miles) east of Phoenix, Arizona. The new tunnel will intercept the waters of Mineral Creek about 2,134 m (7,000 ft) upstream from an existing tunnel. The 5.74 m(18.83 ft) hard rock TBM will break into the old tunnel about 2,162 m (7,090 ft) in from the old portal after mining 3,888 m (12,753 ft). The TBM will mine through a series of igneous and metamorphic formations including volcanic tuff, soft volcanic ash, massive diabase, fractured quartzite, and schist. The TBM will hole through into the existing 4.88 m (16 ft) dia. horseshoe tunnel where the TBM will be disassembled and removed from the tunnel.

Jan 1, 2001

By Mohammed Laraba, Rodrigo Alvarez Garcia, Juan Maria Menendez-Aguado, Roula Abdelmalek

The aim of this research is the study of the WHIMS parameters on the improving process of a local (DD: Djebel Debbagh, East of Algeria) kaolin. The obtained results of performed XRF, SEM, and XRD characterization showed that this local material is an alumino-silicate containing kaolinite and halloysite with MnO and Fe2O3 impurities (respectively 39.30% and 34.67% alumina and 38.18% and 39.70% silica in both samples (DD2 and DD3). After homogenization, crushing, and milling, a multiparameters factorial experimentation (grain sizes, intensity, and dimension of matrix balls) showed that WHIMS is an effective process to improve the quality of this kaolin, mainly: removing their impurities. Dimensions of matrix balls (Db) = 2 cm, intensity of the applied magnetic field (I) = 1.5 T, and grain sizes (Dp) = > 100 < 250 μm) are the optimal values to reach 91.06% for manganese and 93.45% for iron as removing yield. The statistical analysis of these results sorted the investigation parameters and showed that Db has the highest and most significant influence on the recovery of iron and manganese particles. The magnetic field intensity (I) has a less important influence while the grain size has an average influence (positive on the iron recovery but a negative one on the recovery of manganese).

Jun 11, 2022

By C. Iglesias

Innovation in the tilemaking ceramic industry is stressing properties like powder flowability, ability to toughen green tiles, so turning technological requirements of ball clays ever stricter in terms of plasticity, dispersion in water, rheological behavior, workability in the green state, refractoriness and firing colour. Technological performance of ball clays was improved by taking as benchmark the highest quality raw materials on the market. The mineralogy, plasticity, methylene blue index and ceramic response of the Patagonian ball clays are analogous to those of European clays, but improvement is needed to approach the highest quality materials. On this basis, the Frente A, Super, Puma, and Lote 8 deposits were selected and their characteristics enhanced by additions of highly plastic and white-firing corrective clays targeted on the benchmark. Porcelain stoneware formulations, containing improved ball clay mixes, were experimented at both laboratory and industrial scale. The improved ball clays behave like the best raw materials currently used, although modest changes occur in the mechanical properties, water absorption and whiteness of the fired products.

Jan 1, 2010

By J. Hallowell, M. Conley, R. Cook

Inflatable friction rock bolts (IFRBs) are often considered temporary ground support due to their susceptibility to weakening from corrosion. The effective service life of an IFRB can be difficult to estimate due to the multitude of factors that affect the rate of corrosion. Some mine sites have experienced several-year-long service lives of IFRBs without issue, while others experience corrosion-related falls of ground only weeks after installation. The most common industry method of assessing bolt performance is by pull testing the fixture. However, due to the IFRB’s ability to mobilize its full tensile capacity with less than 2 feet of anchored length, corrosion along the bolt at depths greater than 2 feet from the collar cannot be identified using this approach. Alternatively, reinflation testing is a simple and non-destructive method of evaluating the condition of an entire bolt length for breaches in the bolt wall. This can be particularly useful when assessing the extent of corrosive conditions within a particular mining area where instabilities have already occurred and the condition of nearby bolts is unknown, or when re-entering historic mine workings which have not been monitored.

Feb 1, 2023

By Irwan Halim, Young Jin Park

A new tunnel lining was designed for rehabilitation of the existing unlined Weehawken Tunnel in New Jersey. Structural assessment using beam spring models was performed for the lining design as a drained structure at the invert with a waterproofing umbrella. Empirical Federal Highway Administration (FHWA) guideline was typically adopted for estimating hydrostatic pressure, which recommends full hydrostatic pressure at the crown and ten or twenty-five percent gradual reduction from the initial pressure toward the invert. Finite element seepage analyses were conducted for the actual conditions based on anticipated drainage behind the lining and impact on the structural design. Considerations will be provided on the existing guideline for estimating hydrostatic pressures.

Dec 1, 2022

By I. Demers, A. Blier, M. Mbonimpa, M. Benzaazoua, B. Bussière

The Doyon Mine in Quebec, Canada, evaluates the possibility of desulfurizing its tailings to produce material to be used as cover for the acid-generating tailings disposal site. Laboratory tests showed that a single-layer cover made of desulfurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modeling with the software Vadose/W was used to optimize the design parameters, namely, cover thickness, water table position and residual sulfide content of desulfurized tailings following laboratory work. It was found that the optimal configuration includes a 1-m (3.3-ft) desulfurized tailings cover containing 0.8% S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux toward acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective for oxygen flux chosen for the Doyon Mine (10 mol/ m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2009

By G. Simmons

Santa Fe Pacific Gold Corporation (SFPGC) conducted pressure oxidation pilot plant studies at Hazen Research, Inc. on the Twin Creeks refractory carbonaceous gold ores during 1993 and 1994. Previous laboratory investigations demonstrated very good gold recoveries of 90 to 95%, using CIL cyanidation after batch pressure oxidation. However, results from the pilot plant showed that several ore types responded very poorly, with gold extractions of only 45 to 75%. Since these poor recoveries were unexpected, pilot plant testing was suspended for approximately four months while extensive research activities were conducted to determine the cause(s) and identify potential solutions. This paper describes the batch and pilot plant test results, the research activities that eventually identified the cause of the gold recovery problem, and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions.

Jan 1, 1997

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The early mining of iron ore in Minnesota was carried on with the most primitive kind of tools. The pioneers used only such equipment as could be packed from Duluth through one hundred miles of forest to the first mines on the Vermilion Range and the operations were carried on with picks, shovels, hand drills and wheelbarrows, the ore being hoisted in buckets with a horse winch and carted in horse drawn wagons to the stockpile. This was about the extent of the mechanical equipment of the Minnesota iron mines in the early eighties.As soon as a railroad was pushed through from Two Harbors to the Vermilion Range the equipment began to be improved upon; wood burning steam boilers were installed and small steam puffers displaced the horse-winches, wheelbarrows were aban¬doned and small cars were introduced. Hauling the hoisted ore in wagons was discontinued and trestles were built so that the ore could be stockpiled more cheaply through the use of cars and high piles. These same stockpiles were loaded by hand into the 10 and 15 ton capacity railroad ore cars.Within a few years a marked change took place—the hand drill gave place to the air drill, such as No. 3 Rands, Ingersolls, Sargents and some Sullivans. Tramming was done by mules, the ore hoisted in. self-dumping skips, hoisting engines were intro¬duced and it seemed as though mining as a business in Minnesota had come to stay. At this stage someone conceived the idea of making the stockpile floor about three feet above the top of the ore cars to facilitate the hand loading of stockpile ore for trans¬portation. This was done through the use of wheelbarrows at first and later by using I-ton cars running on tracks laid on the stockpile floor."

Jan 1, 1920

By Dr. Ing. Hermann Boldt

The Bituminous Coal Mining Industry of the Federal Republic of Germany produces nearly 100 million t/yr of clean coal. The largest coal mining area is the Ruhr District with dimensions of 100 x 40 km (65 x 25 miles). Figure 1: Here is the general administration of Ruhrkohle Akteingesellschaft RAG with its three divisions. Other coal mining areas in Germany are the Saar District and the Aachen District. Ruhrkohle produces 70 million t/yr of clean coal. The company operates 28 mines in the Ruhr District with an average raw coal production of 18000 t/day. Their average mining depth is 831 m (2740 ft.) and the average seam thickness is 177 cm (70 in.). Figure 2: Preparation plant reject is 44.6%. All following production figures will be with reference to raw coal because the raw coal production is the technically relevant number. Mining operations are mainly in non-dipping coal deposits whereby mechanized equipment for flat seams is also applied to deposits dipping up to 45? Coal extraction is done exclusively by the longwall method. Approximately 200 longwall installations are in production at any time. The average longwall length is 221 m (730 ft) ranging between 140 and 290 m (460 ft and 960 ft). The average longwall advance of all operations is 2.8 m/day (8.4 ft per day). Average production

Jan 1, 1977

By R. R. Klimpel

This paper describes four new families of flotation products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1992

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only &apos; about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980