Search Documents

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969

By Donald I. Bleiwas

The U.S. Bureau of nines evaluated the potential availability of tungsten from 57 tungsten mines and deposits in 19 market economy countries (1). The 38 properties that were producing at the time this study was performed contain approximately 375,000 tons1 of W03 (tungsten trioxide). The total estimated recoverable resource from all properties studied, both producers and nonproducers, was 1.2 million tons W03 (demonstrated level). Approximately 143,000 tons of W03 is recoverable from producing properties with costs at or below the January 1983 market prices. The study indicates that by 1990 production from currently operating mines in market economy countries will decrease as their demonstrated resources become exhausted. Some of this potential decline may be offset by lower than anticipated levels of market demand, discoveries of additional resources at producing mines, development of other known deposits, and/or discoveries of new deposits. Development of new tungsten resources in market economy countries will likely result in costs higher than exist at currently producing properties. The People's Republic of China has been steadily increasing production and export of tungsten in various form and currently supplies about 25 pct of U.S. imports. China's tungsten mines are large, high-grade operations capable of producing at relatively low cost. These factors, coupled with China's apparent need for foreign exchange, could lead to further expansions of production and exports from China, with a consequent increased dependence by market economy countries on China for tungsten requirements and a threat to the survival of the market economy countries' tungsten industries.

Jan 1, 1984

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world's largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

Careful financial analysis of capital investments has always been a vital task in mining which is one of the most capital intensive sectors of the economy. Furthermore, mining costs have leapt ahead at an astonishing rate in recent years not just due to accelerated inflation, which affects everyone, but also due to the imposition of enormous costs of enviromental regulation and the continuing decline in ore tenor. Not only have unit costs risen, but the amount of effort expended to recover a pound of metal has increased due to the inexorable decrease in ore grades. New low-margin, high-volume mining investments place increasing importance on sound financial planning. Owing to the enormous investments involved, a greater share of individual corporate resources is committed to these projects than is normally the case in other industries. Thus, the consequences of failure are extremely grave, and a close examination of all inputs to the evaluation equation is clearly indicated.

Jan 1, 1979

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy&apos;s (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984

By Bauer, Steve, Colin Goodwin, Gerald, Randy Dempsey, Courtland

"The City of Ottawa’s Combined Sewage Storage Tunnel consists of two interconnected tunnels totaling 6.2 km with a diameter of 3m including access shafts and hydraulic structures which connect to the City’s most critical sewers. This tunnel will be built 15m to 30m below ground in the downtown core adjacent to, and crossing below, the Light Rail Tunnel, which introduces additional considerations in terms of sequencing and risk mitigation. The City embarked on a unique Procurement Process to address the risks involved with a large tunnel project and those associated with tunneling below downtown, underneath and adjacent to UNESCO World Heritage Sites, and connecting to live critical sewers. This paper describes the unique procurement approach employed and the contractual risk mitigation measures developed to provide the best value while minimizing risk. Specific features include Market Sounding, using a Fairness Commissioner, Contractor Prequalification and Risk Mitigation Measures in the Tender documents. INTRODUCTION This paper describes how the City of Ottawa (the City) and the project design team developed a strategic Procurement Process and Tender that incorporated industry best practices for technical and contractual risk management for the Combined Sewage Storage Tunnel (CSST) project. The process was unique in that, while it employed a systematic review of project risks, it also solicited input from industry, stakeholders and provincial and federal partners to develop the request for Tender for this traditional design-bid-build project. Key drivers for this approach were initiated from the City’s concerns for cost control, cost certainty and overall project risk mitigation. To address these concerns, the City implemented the risk review and mitigation process right from the project design team selection. It was critical that the project design team embraced this risk management philosophy and carried it through each phase of the project. This paper serves as an excellent resource for municipalities or other owners embarking on a similar tunnel project, on how to properly apply industry best practices and the benefits of using them."

Jan 1, 2016

By Manuel Gomez

This, report presents correlative data on ash and sulfur forms for Pittsburgh seam coal from Greene County, Pa. Prediction equations were developed for sulfur form distributions and washability characteristics. The equations developed were evaluated with an independent set of exploration core samples. It was demonstrated-that both sulfur distributions and washability characteristic&apos;s can be predicted from exploration core data ahead of mining. This information can improve the efficiency of selective mining techniques for the production of a uniform metallurgical coal product.

Jan 1, 1967