Search Documents

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By G. Robson

"From monitoring gas levels and air quality in coal mines to protection from collisions for large vehicles at mine sites, SICK offers a wide range of sensors and systems to improve safety and to monitor potentially dangerous situations. SICK offers solutions for the analysis and monitoring of underground coal mining atmospheres. These systems supply the coal mine operator valuable safety and ventilation information, as well as data which identify and monitors atmospheres of those production areas within the mine which may or may not be worked, such as Goafs and sealed areas. Underground coal mines contain dangerous gases, which must be monitored and controlled in order to allow productive mining operations to take place and to minimize the risk of explosion. Underground mines are a potentially dangerous place for mine workers. These are the main reasons for using Tube bundle systems SICK has had great success in selling these systems into the Australian and New Zealand Markets and this is helped by the strong drive for mine safety from both the Mine Owners and the Regulatory bodies charged with the responsibility of ensuring Mine Regulations are met. The Australian mining industry uses Tube Bundle Systems at almost all underground sites, even after mining has ceases and the mine is placed in care and maintenance. Sick has been working in international markets for some time now but has had limited success in selling Tube bundle Systems to these markets. However in recent times there has been raised interest in Tube Bundle from China, India and Turkey as these countries strive to improve mine productivity and lessen the risk of explosion or Spontaneous Combustion. Our lack of penetration into International Coal markets has been very much based on the perceived cost of the system, not the benefits to safety and productivity. Unless a mine has had an event such as spon com or a Methane explosion they rarely consider the very low level measurement capability (20 PPM CO & 100 PPM CH4) or the long term trending benefits of the Tube Bundle system. It is only after a catastrophic event the System is considered. Real Time or electrochemical Sensors are commonly used to monitor the Mine Atmosphere, the real problems of methane build up or potential Spon Com in Goafs and sealed areas cannot be monitored using Real Time Sensors as the electrochemical cell deteriorates after approx. 12 months and in sealed areas these cells cannot be maintained or replaced. Whilst the Technique of Tube Bundle Systems is quite old SICK have spent many years redesigning the Tube Bundle System into a cost effective and real value for money product. The system uses state of the art sampling and highly accurate Infra-Red wide Spectrum Analysers."

Jan 1, 2016

By W. M. Cross

The hydrophobic character of sapphire surfaces in SDS solutions was examined with respect to the aggregative nature of the adsorbed surfactant phase. It was found that, at equilibrium, sapphire surfaces having adsorbed SDS bi-layers exhibited no contact angle. Conversely, when the adsorbed SDS was found to be mi-cellar in nature, sapphire surfaces developed significant hydrophobic character. The surface states as detected by Fr -IRIIRS conformational analysis were found to be reversible with temperature. The variation in adsorption density with temperature was studied by in situ Fr-IRIIRS. The isosteric heat of adsorption was calculated to be -1.6 kcal/mole. Although the adsorbed SDS was found to undergo a reversible phase change between 25 and 32°C, similar to SDS in solution, the extent of adsorption was not reversible with temperature.

Jan 1, 1993

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By Walter B. Hester

All persons and communities that have experienced strong-motion earthquakes are convinced of the importance and complexity of earthquake problems thatmust be solved in order to reduce the personal hazards and property losses to a reasonable minimum. It is also clear that absolute elimination of all risks is impossible. Reduction of existing hazards and precautionary measures which will minimize chances for disaster can be accomplished by realistic appraisal of the effects of recent earth- quakes on modern structures and installations. Localities that have reason to expect so-called strong- motion earthquakes can anticipate these effects by taking appropriate steps. Valid earthquake information can only be obtained from earthquakes. Each earthquake contributes to the body of knowledge by additional facts and by clarification of previous observations. Rational interpretation of the data followed by practical application of the conclusions can contribute greatly to the safety of persons and property. The general public expects the architectural and engineering profession to accept this obligation and render this service. Most earthquake hazards are man-made and arise from the imperfections of the works of man and his failure to anticipate the consequences when the natural characteristics of his environment are ignored. If it is not given to man to prevent such natural phenomena as earthquakes, it is sometimes within his power to control their destructive effects and to reduce to a minimum the toll of life and human suffering.

Jan 1, 1958

By A. D. Davis

Naturally occurring arsenic has been detected in water from inactive mines and several wells in the Keystone area of the Black Hills. Keystone City Well #4 showed a total arsenic concentration of 69 parts per billion (ppb) during pumping in 2004. The well is not used currently except for arsenic-removal research. Water also can be pumped from a mine shaft in the abandoned Keystone ? Columbia ? Bullion gold mines, whose interconnected workings flooded after mining ceased in the 1930s. This water has been considered for local supplies, although it would require treatment or blending because of arsenic concentrations. According to historical records, the Bullion Mine produced 100,000 pounds of white arsenic. An aquifer test on the mine workings was performed at a pumping rate of about 550 gallons per minute. The arsenic concentration in pumped water was 33 ppb. In addition to wells within Keystone, samples from the water supply at nearby Mount Rushmore National Memorial have shown arsenic concentrations greater than 10 ppb, the U.S. Environmental Protection Agency?s maximum contaminant level for arsenic in drinking water. Limestone-based technology for removal of arsenic from drinking water is an innovative and promising method that has been considered for treatment of water at Keystone. In batch testing with water from Keystone Well #4, limestone removed about 65% of arsenic from solution. A related problem of arsenic removal from drinking water involves disposal of the waste product, which is critical for commercial viability of removal technologies. Current research is investigating thermal stability of the waste in order to determine the potential for recycling of the material during manufacture of cement.

Jan 1, 2010

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By P. A. Mingione

AEROPHINE® 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn-and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treat-ing different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.

Jan 1, 1991

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020