Search Documents

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By J. F. Barry

Newmont Mining Corporation and Barrick Goldstrike Mines, Inc. concluded an exchange of land and reserves in an agreement signed May 3, 1999.This exchange of assets allowed Newmont to develop the Deep Post underground mine from within Barrick’s Betze-Post open pit, thus reducing capital expenditures, lowering operating costs, and advancing the production schedule by nearly three years. Based on previous experience, Newmont is confident that the Deep Post underground mine can be successfully developed and operated within a large, active, open pit mine. The project also faces difficult geotechnical conditions including weak ground, scattered pockets of groundwater, and elevated rock temperatures.

Jan 1, 2000

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

By Brian F. Osborne

A continuous on-line particle size analysis system for solid/liquid suspensions is described. The basic sensor utilizes a centrifugal principle to separate particles according to size, the resultant separation being measured by means of beta-ray attenuation. Results obtained when analyzing a variety of materials at sizes from 65 mesh (210 microns) to 20 microns are discussed in de- tail. Accuracies better than 2% are demonstrated. The effects of particle specific gravity, and mixtures of materials of diverse specific gravities, are discussed from a practical and theoretical viewpoint. It is demonstrated that particle specific gravity has a minimal effect on the size reading obtained. This renders the instrument suitable for handling materials where the ratio of light to heavy component may change. The design of the first commercial installation of this instrument is described in detail. This installation will be capable of analyzing three streams in sequence, measurement at three particle sizes being effected on each stream.

Jan 1, 1973

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By Rambabu Pothina, MELO EDUARDO PIMENTA DE, Rajive Ganguli

 The mining industry is home to a mass of sensor-generated data that are critical to real-time and long-term optimization. This heavy reliance on sensor data has resulted in an undesirable development. The industry is reluctant to verify the accuracy of sensors as it would mean shutting down important processes. Sensors are typically calibrated once a year, if at all. Errors in sensors go undetected until the next calibration or until errors are so gross as to be obvious

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Pratt Rogers, Aaron Young

This paper considers the mining industry’s need for digital transformation (DT) and presents a three-part review of the foundational components of the DT process: ubiquitous data, connectivity and decision-making. It also provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By Lixue Wen, Jun Xiao, Dongping Shi, Yan Xue, Jinmiao Wang

Mine ventilation energy consumption is one of the main sources of energy consumption in mining production, accounting for about one-third to one-half of the total energy consumption. Therefore, reducing the energy consumption of the mine ventilation system is crucial for mining production. With the premise of meeting the airflow requirements of the underground work areas and achieving sustainable development of mining production, this paper establishes a nonlinear optimization mathematical model for the mine ventilation network with the objective of minimizing the total power. Regarding the model, optimization of the decision variables was carried out using the method of minimum spanning tree. The constraints for air flow balance, wind pressure balance, and fan operating conditions were optimized using the exterior penalty function method, thereby transforming the model into a nonlinear unconstrained model. Based on this model, a modified sooty tern optimization algorithm (mSTOA) was proposed to achieve optimization. Improved the sooty tern optimization algorithm (STOA) by using the uniform reverse strategy, fitness value-distance balance selection strategy, and mutation strategy. The STOA, mSTOA, and three other classical optimization algorithms were applied to the optimization of a ventilation system of an actual mine. The experimental results show that after using mSTOA to optimize the ventilation network airflow distribution in the mine, the total energy consumption can be reduced by about 35.06% while meeting the constraints and demands of the ventilation network regulation and usage. This is of great value to mine roadway operation environment safety and clean production.

Dec 20, 2023

By Changshou Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,175 t (3,500 st) of ore per day with an average gold grade of 12.6 g/t (0.4 opst). The mine has a large horizontal extent of 762 by 152 m (2,500 by 500 ft) and a vertical extent of 6 to 61 m (20 to 200 ft). Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for mining design and operation in the Leeville underground mine. Three methods are used to collect the geotechnical data in the Leeville underground mine: • Core logging. Most geotechnical data are collected by this method, which is based on exploratory drills and estimates parameters for rock quality designation (RQD), fracture frequency (FF), compressive strength and rock mass rate (RMR). • Site investigation. This method collects more detailed geotechnical data and geostructural data from work done in the underground drifts and stopes. Parameters of RQD, FF, compressive strength, RMR, rock tunneling quality index (Q) and geostructural data are estimated. • Data collected from drill holes made for the critical infrastructure facilities. This method provides the best detailed geotechnical information for areas in which the critical infrastructure located. A complete geotechnical database has been constructed using this geotechnical data collection system. The database can be used for the design of ground support, stopes and stope blasts, among other critical applications.

Jan 1, 2010

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By Lei Zhang, Zhibo Ma, Pingye Guo

The mechanical behavior of hard roofs often leads to significant deformation and strong mine seismicity in gob-side entry retaining (GER) of the longwall mining, affecting the mining safety and efficiency of coal mines. Field investigations indicate that the failure process of the retained entry by hard roofs can be divided into three stages. In this paper, theoretical analysis and numerical simulations are first used to evaluate the damage process of the retained entry under the hard roof. The results show that the instability of the retained entry in the conventional GER method results from the combined static-dynamic loads (in stage II and stage III) from the hard roof. Then, an innovative method, through fracturing roofs to maintain entry (FRME), based on GER with the hard roof is introduced to solve this problem. In this method, the roof of the mining area is pre-fractured, and when the coal seam is mined, the direct hard roof will collapse along the fractured surface due to its deadweight and mining pressure. The hard roof control effect on the static and dynamic loads, taking into account the innovative method, is verified with simulations and theoretical analyses. The results are compared with those of the conventional GER method. Furthermore, based on the numerical simulation study of dynamic responses, it is found that compared to the GER method, the dynamic response of the retained entry using the innovative method is more moderate and more conducive to the stability of the entry. Field application also validated the effectiveness of the innovative method to control the mechanical behavior of the “massive sudden collapse” of the hard roof.

Aug 14, 2023

By Nikhil Dhawan, SHAILA MIR

The emerging problem of electronic waste has promoted the interest in exploring metal recovery from secondary sources under the umbrella of urban mining. This study presents the physical and chemical characterization of various components present in end-of-life laptops to help ascertain the sites of metallic values and develop sustainable and environment-friendly recycling. The recycling potential of a laptop is evaluated by sequential disassembly, separation, and characterization of components such as body (49.8 wt.%), printed circuit board (9.7 wt.%), hard disk drive (4.9 wt.%), and battery (12.4 wt.%). The printed circuit boards comprise metallic values, majorly copper (25 wt.%), tin (5.8 wt.%), and lead (3.1 wt.%). The precious metals (Au, Ag) with an economic advantage are abundantly present in electronic components such as integrated circuits, capacitors, resistors, and processors. Critical elements such as lithium, cobalt, and rare earth elements are detected in the discarded laptops' batteries and hard disk drives. The recycling potential representing the amount of material that can be recycled in various components, depending on the type, concentration, and purity, is determined in the range of 36–100%. On average, a unit laptop contains~ 386 g of Cu (14.45 wt. %), 49.73 g Co (1.86 wt. %), ~346 mg Ag, ~141.2 mg Au, ~650 mg of rare earth elements (Nd, Dy). This study presents a database for investigating integrated and economical recycling techniques from different components of a laptop, and an overall process flow is also proposed.

Jul 24, 2021

By Georgene Renner, Chee Theng, William Gleason

"With more than 900 booth spaces sold and 630 exhibiting companies displaying their wares, there was something for all 7,804 attendees on the exhibit floor of the 2015 SME Annual Conference & Expo in Denver, CO Feb. 15-18. The following is a sample of what was offered at the 2015 meeting.3D Laser MappingData collection and data analysis are changing how mining is done. One field in which technological advancements have made safer and more efficient operations possible is through site and slope monitoring.3D Laser Mapping, a United Kingdom-based company, was on hand at the 2015 SME Annual Conference and Expo to display its solutions for the mining industry, including its SiteMonitor4D system.The state-of-the-art laser measurementbased system was developed in partnership with geotechnical engineers and mining surveyors, and is a simple-to-use, reliable solution that has the flexibility and performance to function in a range of monitoring applications.The system measures and monitors the stability of rock faces, landslips and man-made structures, including ongoing, periodic measurement of volumes - stockpiles, cutbacks and waste dumps and has high-speed laser scanning for regular mapping of large areas by mounting the scanner on a vehicle.With specifications that other monitoring techniques cannot achieve, laser scanning opens up a new dimension in mine measurement and monitoring.www.sitemonitorsystems.comA.R. Wilfley and Sons Inc.Founded in 1919, A.R. Wilfley and Sons Inc. has been manufacturing dynamic-seal and static-seal pumps in Colorado for nearly 100 years, delivering its high-reliability, low-maintenance, heavy-duty process pumps and slurry pumps to the global mining industry. The family-owned company is now in the hands of the fifth generation."We are the dynamic-seal experts," regional sales manager Cesar Murillo said. "Most other companies are unable to do 100 percent dynamic seals and have to use mechanical seals or packing," he said, but Wilfley’s sealing technology does away with the need for mechanical seals and packing and their associated problems. As a result, solids and slurry handling capabilities are high, the pump can be run dry, and product dilution is eliminated. The pump can tolerate more misalignment, more cavitation, and more vibration in the pump during operation."

Jan 1, 2014

By Ben Benally, Joseph M. Hans

INTRODUCTION The decontamination of the former Shiprock uranium millsite and the interim stabilization of its tailings piles began in March 1974, and ended in June 1978. Personnel monitoring for whole body gamma ray exposure was conducted for selected individuals working at the mill site throughout most of this period. The millsite and exposure conditions are briefly described to develop a basis for interpretation of the exposure data. Millsite The Shiprock uranium millsite is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the millsite are located on the Navajo Indian Reservation. About 1.5 million tons of tailings were produced on the millsite during its operation from 1954 to 1963. The tailings were pulped with waste process fluids and water, and discharged to form two tailings piles. The piles (ponds, dams) were formed with earth starter dikes and the dikes were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and tailings reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a tribal enterprise. In addition to its regular activities, NECA established an on-site training school for heavy equipment operators. The trainees principally used the south tailings pile as a practice area and spread the tailings into a 10 hectare row of raffinate ponds located along the southwest side of the millsite. Overall, the training activities inceased the effective area of the tailings piles from 20 to 35 hectares. Another 56 hectares were contaminated with wind and water eroded tailings. Exposure Conditions Persons decontaminating a millsite may be subject to radiation exposures from several sources. Only whole body gamma exposures are discussed in this report. These exposures are arbitrarily divided into three levels: high, intermediate, and low. The levels are related to areas in which the decontamination work was being done and have no connotation concerning imminent hazards. High exposures would result when persons were working with raw tailings, and intermediate exposures would occur when persons were working in the ore storage and mill yards. Low exposures would result from working in areas where surface contamination exists from wind and water erosion. [ ] The millsite and its contaminated environs were divided into major areas to facilitate the decontamination work (Figure 2). Areas A, B, and C are defined as perimeter areas containing surface contamination. Work in these areas was expected to result in low exposures. Areas D, E, and F are the

Jan 1, 1981