Search Documents

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior ofTiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was 150 and that of the silica in the same system was 0.02, resulting in a separation factor of 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

Coal that meets customer specifications is often stored in silos before being loaded into cars. It is often found that coal in a particular car does not meet customer specifications due to the mixing of coal inside the silo. Some new contracts require meeting specifications on a per car basis. Silo flow models are used to predict quality in such cases. However, coming up with an accurate silo flow model for each case is very difficult and time consuming. This paper examines the viability of using an online analyzer at the loading end of the silo in conjunction with a feedback circuit, to optimize the quality of the coal being loaded into trains, so that each car meets quality specifications.

Jan 1, 2000

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By Ed Cope

The newly discovered South Arturo deposit is a Carlin-type, breccia-hosted, oxide gold deposit located on the Dee Mine property at the north end of the Carlin Trend in Nevada. The Dee Gold Mine was discovered in 1981 by Dee Delamar, a Cordex geologist. The property was put into production by Rayrock Mines in 1984. During its 16-year mine life, the Dee Mine produced about 18.6 t (600,000 oz) of gold from oxide ore at an average production rate of about 1.24 to 1.55 t/a (40,000 to 50,000 oz/year). In October 1997, Bar-rick Gold Exploration acquired the right to earn a 60-percent interest in the Dee property from Dee Gold Mines through an exploration farm-out agreement. Barrick Gold Exploration began exploration activities on the property in 1998 and vested in its 60 percent operating interest in 2004. However, the discovery hole at South Arturo was not drilled until July 2005 from atop the historic mine dumps located 300 m (985 ft) south of the Dee openpit. The discovery hole (BD-72) encountered a cumulative 75.6 m (248 ft) of oxide mineralization grading 1.9 g/t (0.055 oz/st) gold beneath 260 m (855 ft) of dump material and post mineral Tertiary Carlin Formation volcanic and sedimentary rocks. Oxidation within the deposit extends to depths greater than 610 m (2,000 ft). The deposit has passed the prefeasibility test and is presently in the feasibility stage. Exploration is on-going to enhance or enlarge the known deposit. The current resource for the deposit stands at 40.4 t (1.3 million oz) of gold. The South Arturo discovery is an example of an historic mining property yielding a new discovery through the diligent application of area selection criteria of the model type and persevering when early results were generally negative. Barrick?s original exploration pro-grams on the property were focused on the discovery of deep, high-grade sulfide deposits that would likely be mined by underground methods. As it turns out, South Arturo is mostly oxidized and will be amenable to mining by openpit methods

Jan 1, 2008

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By Robert A. Jankowski, J. Harrison Daniel, Fred N. Kissell

Introduction Longwall coal mining in the US has steadily increased since its introduction in 1960. There are now 108 systems operating. (Sprouls, 1986). Advantages of longwall mining include higher productivity, improved safety, and greater coal recovery. Respirable dust, however, is one of the more serious obstacles to realizing the full potential of longwall mining. Early in 1980, the US Bureau of Mines (USBM) initiated extensive in-house and contract research to identify and evaluate effective methods of controlling respirable dust exposure of longwall face personnel (Niewiadomski, Jankowski, and Kissell, 1981). It was found that several control procedures must be combined to assure compliance, using control techniques appropriate to the dust source. These techniques can typically be grouped into the following categories: reduction of dust generation; dilution of dust; capture or knockdown of dust; and dust avoidance. Control techniques can be divided into basic and effective dust control techniques; additional necessary controls; and optional supplementary controls. This information should allow longwall mine operators to select control methods applicable to their particular operations and to develop a dust control plan that meets Federal dust standards. Basic and effective dust control techniques There are three basic dust control techniques (Taylor and Jankowski, 1982) that should be implemented on all longwall mining operations. • A passive barrier or external water spray system design that confines shearer generated dust near the face and away from the operators. • Large quantities of water through the sprays, particularly the drum sprays, to aid in dust knockdown and prevent dust becoming airborne. • A cutting sequence that allows the shearer operators to work primarily on the intake-air side of the lead cutting drum. Shearer clearer There are some poorly designed shearer-mounted spray systems with nozzles directed upwind at the cutting and loading zone of the intake-side drum. These actually carry dust away from the face and upstream of the drum. Where, it mixes with the clean intake air (Fig. la,) and is carried out into the walkway over the shearer operators. The Bureau developed a novel shearer spray system, called the shearer clearer. It takes advantage of the air-moving capabili-

Jan 10, 1986