Search Documents

By S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999

By R. R. Odman

The Malmberget Division of LKAB is located 70 km north of the arctic circle and has about 2000 employees. The dominating products are sinter feed concentrate and pellets. A general flow sheet for the operation is shown in Figure 1. About 20 percent of the ore body consists of hematite, which is mined separately and processed into sinter feed concentrate. That pert of the ore consisting of magnetite passes through a dry cobbing plant. The robbing process includes crushing, screening and dry magnetic separation. The entire cobbing product is used as feed for the wet concentrator. After rod mill grinding and magnetic separation the concentrated slurry is classified. The coarse fraction (+200 mesh) becomes sinter feed concentrate and the slime fraction after further ball mill grinding and magnetic separation, becomes pelletizing feed. A small quantity of the magnetite ore is processed into special iron-rich products in the the wet concentrator. Two types of pelletizing plant are used, shaft furnace and straight grate. This paper will deal only with experience gained at the straight grate plant.

Jan 1, 1979

In phosphate flotation, more than 90% of the finer fraction (-35, + 150 mesh) is recovered as opposed to 70% of the coarser material (-16, + 35 mesh). On the other hand, coarser fraction is higher in phosphate content than the finer feed. Consequently, improvement in the coarse recovery is highly desired. It was determined on bench scale that emulsification of the collector (fuel oil and fatty acid mixture) can lead to enhanced recovery of coarse particles. Flotation of phosphate with emulsified collector resulted in improved recovery and grade also on the plant scale.

Jan 1, 1992

By John William Carlson

The Y2K or "Millenium" bug is a tiny critter, comprising no more than two digits in a date field. This bug, like its' more lethal cousins of biological and computer virus fame, has the potential to derail the economy of the U.S. and the rest of world. Whatever the reader's perception, rest assured that you will be affected by Y2K along with every person in the civilized world. How did we get to this position? It is really quite simple. The Y2K problem is a creation of computer programmers who, in an effort to conserve valuable memory in the early days of computer development, used two digits as shorthand- to define the year in date sensitive applications. Instead of typing in "1982," our experts employed "82." They believed-correctly­that the problem of limited memory would be solved by technology and assumed (nasty word) that software would be modified to take care of any problems associated with a date rollover in the year 2000. Their assumption resulted in the problem facing us today.

Jan 1, 1999

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

The new generation of computer environment provides mineral processing plants with convenient tools to store and retrieve or to analyze on-line process variable values as given along time by the various sensors installed in the plant. The paper describes the application of classical tools, such as time series analysis, to retrieve the hidden information contained is such data. The concepts used in single signal processing (autocorrelogram, power spectrum, ARIMA descriptors) and multi-signal processing (cross-correlogram, cross-spectrum) are briefly reviewed. Some examples are given to illustrate their application (sampling, data filtering, process behaviour prediction, process evaluation, data synchronisation). Examples are taken from mixing, flotation and leaching processes.

Jan 1, 1990

By F. Robert Hollo

Programmable controllers have achieved remarkable acceptance over the relatively few years since their introduction. They provide some unique advantages over conventional relay and solid-state logic, which they often replace. Programmable controllers are discussed in both conceptual and functional terms, followed by an exploration of their applicability to material handling tasks with particular emphasis on conveyor systems.

Jan 1, 1973

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Wei Li

Carbothermic reduction kinetics of ilmenite concentrates catalyzed by sodium chloride and the microwaveabsorbing characteristics of the resulting reductive products were investigated; the reduction degree of the reaction was deduced to be . Results show that the activation energy is 112.03 kJ/ mol when NaCl is used as catalyst, lowering to 23.11 kJ/mol for the final stage activation energy using sodium silicate as a catalyst. There is a sharp change in the reduction rate constant at temperature ranges of 1,223 K - 1,273 K and 1,373 K - 1,423 K. Microwave-absorbing characteristics of reductive products were measured by the method of microwave cavity perturbation. It was found that microwave-absorbing characteristics of reductive products obtained at temperatures of 850° C, 1,100° C and 1,150° C show sharp changes. Through X-ray diffraction (XRD) characterization, it was found that the formation of Fe occurs at a temperature of 900° C during the reduction process of ilmenite concentrate. The decrease of FeTiO3 content results in the decrease of microwave-absorbing characteristics, while the increase of Fe content gives rise to the increase of microwaveabsorbing characteristics. The decreasing trend is larger than the increasing trend, which is the main reason for the sharp changes in the microwave-absorbing characteristics of reductive products at the temperature range of 850° C to 900° C. When the decreasing trend is smaller than the increasing trend, it becomes the main reason for the sharp changes in microwave-absorbing characteristics of reductive products at the temperature range of 1,100° C to 1,150° C. Kinetics results show that sodium chloride can catalyze the carbothermic reduction of ilmenite, and microwave-absorbing characteristic investigations indicate that microwave heating can be used in the carbothermic reduction of ilmenite.

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Pierre Dosmond

In ore mining technology, the loading and hauling operations are undoubtedly the area where the most spectacular progress has been made during the last twenty years. I shall draw some examples from the Eastern France iron ore mines which I how well and whose production of 62 million tons for 1962 and 1963 constitute a worthwhile experience worldwide. The iron ore deposits of Lorraine are of sedimentary origin. They contain many mineralized horizons with workable seams situated from 330 to 830 ft. in depth. The dip of these seams is generally less than six percent. Their thickness varies from 6 to 23 ft. All seams are not workable throughout the whole area of occurrence, but in some mines there are five mineable seams in the same vertical section, with from 5 to 20 ft. of barren ground intervening between them. The iron content of the mineral varies from 28 to 36 percent. Specific gravity of the ore is 156 lb. per cu. ft. m place and 100 lb. per cu. ft. blasted. Reserves of iron ore in the Lorraine region are estimated at six billion tons with an iron content of more than 28 percent. These mines operate by means of rooms and pillars process, with pillar robbing; the final recovery is very good and averages 90 percent. Some years back, competition from richer, imported ores incited these mines to make constant efforts to increase their productivity and reduce mining costs, thus placing them in a leading position in mining technology, as evidenced by the dramatic evolution of their output per manshift (Figure No. 1).

Jan 1, 1970

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By K. F. Unrug

Fractures of sedimentary rocks in the vicinity of the outcrop are commonly encountered around the world. Mine highwalls and numerous highway cuts give excellent views for detailed study of surface fractures. This paper gives an explanation of the origin of fractures as well as characterization of the distribution and extent of joint system with reference to lithologic composition of the rocks. Practical implications of the joint system affecting mine operations are described. Among the subjects discussed are: discontinuous deformation as an effect of surface subsidence, stability of mine portals and near outcrop underground operations, and stability of highwalls, when using highwall miners and strip operations. Some design procedures are recommended that can minimize the problems encountered in mining areas with intense joint systems.

Jan 1, 1994

By Lawrence Neal Post

Introduction Synthetic soda ash production began to decline in the late 1930s. This was due to high operating costs and waste disposal problems. Since soda ash was used as a major component in manufacturing glass, an alternate method of producing that chemical was necessary. A process to produce soda ash from trona was developed by FMC Wyoming Corp.'s predecessor, as well as an economical way to obtain trona. Existing trona operations are located about 40 km (25 miles) west of Green River, WY. Five operators presently mine trona in this area. FMC's property has 153 km2 (59 sq miles) leased. Its eight shafts reach 488 m (1600 ft) deep to the uniform trona deposit. The seam ranges in thickness from 2.4 to 3.6 m (8 to 12 ft). History Egyptian tombs, dating from 4000 to 3000 BC, contained mummies preserved by an embalming process using soda ash. For many years, soda ash was produced by burning marine plants, then dissolving the soluble material (sodium carbonate) from the ashes. The name soda ash is derived from this method of production. In 1791, Nicola LeBlanc developed black ash, or salt cake, from salt, sulfuric acid, coal, and limestone. This process remained in use until 1863, when Ernest Solvay developed a method for producing soda ash from salt, coke, and limestone with ammonia as a catalyst. This Solvay process was widely used. And, in the 1930s, there were 17 plants in the US alone. High plant operating costs and waste disposal problems, however, necessitated finding an alternative to the Solvay process.

Jan 10, 1985

By James W. Cooksley

This report concerns a seismic geophysical exploration program which was conducted 3 miles southeast of the Carlin Mine, in Lander County, about 18 miles north of Carlin, Nevada. A twelve-fold reflection seismic line was executed over a one-mile traverse in section 32, Township 35 North, Range 51 East. This study is part of an exploration pro- gram directed toward finding Carlin-type gold deposits which are concealed under younger alluvium and volcanics. The exploration objectives of this program are as follows: 1) measure the thickness of the younger, sedimentary and volcanic deposits which overlie the "productive rock sequence", 2) delineate the Roberts Mountains thrust fault, 3) investigate the origin of the geochemical anomalies present in the western portion of section 32.

Jan 1, 1985

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn't like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we've already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn't exist without concrete. And you can't have concrete without aggregates,

Jan 1, 1977

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Wayde Esplin

At the Barrick Goldstrike processing facilities in northeastern Nevada, sulfide ore is pressure-oxidized at a temperature of 440° F and 420 p.s.i. in six autoclave circuits. The low pH, high temperature, and abrasive characteristics of the oxidized slurry present many new and unique maintenance challenges. To meet these challenges, the Barrick Goldstrike autoclave department formed a reliability group in August 1998. One of this group's critical missions is to reduce both maintenance costs and unscheduled downtime through the application of predictive maintenance technologies and Reliability Centered Maintenance Analysis. This paper discusses some of the successes of the reliability program at the Barrick Goldstrike autoclave.

Jan 1, 2000