Search Documents

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By E. Milke, A. Arnold, B. Friedrich, A. Sydykov

CaF2is often used as a fluoride addition to the chloride salt flux in the melting of aluminium scrap. The solubility of CaF2in the chloride salt system is limited. Dissolved CaF2is considered to improve the properties of salt fluxes. Experimental investigations indicated that the solubility ofCaF2in 70 wt % NaCl/30 wt % KCl, German salt flux used in aluminium scrap melting, might be lower than expected according to literature data. The pseudo binary section CaF2-(70 wt % NaCl-30 wt % KCl) was investigated by differential thermal analysis (DTA). The determined solubility of CaF2appeared to be considerably lower than presented in the literature. The pseudo binary section calculated using thermodynamic data partially confirmed the results. DTA allowed us alsoto determine the crystallization temperature interval of the two phase eutectic consisting of the solid solution NaCl-KCl and CaF2. Keywords: aluminium recycling, phase system, salt flux, CaF2, NaCl, KCl, solubility

Jan 1, 2004

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Junior S.J. Ramokgopa Immediate Past President J.R. Dixon Honorary Treasurer J.A. Cruise [ ] Annual report In accordance with the current management policy, this report on the activities of the Institute is presented under eight main headings: 1. Interests of Individual Members 2. Technical Meetings 3. Publications 4. Regional Development 5. Engineering Science and Technology in South Africa 6. International Liaison 7. State Liaison 8. Management and Administration.

Jan 1, 2001

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

The functional design of a pavement relates to the selection of appropriate wearing course materials which optimise the trafficability of a pavement. Trafficability is dictated to a large degree by the choice, application and maintenance of locally available wearing course materials. Poor functional performance results in decreased safety and operational efficiency and increasing road and vehicle maintenance requirements. An optimal functional design will include a certain amount and frequency of maintenance (watering, grading etc.) and thus maintenance itself can be planned, scheduled and optimized within the limits of required road performance and minimum vehicle operating and road maintenance costs. Since no wearing course material selection guidelines, tailored to the specific needs of surface mines, were available, there was the need to identify appropriate selection guidelines for the range of materials commonly encountered for road building on South African mines. The aim of this paper is to present an overview of the functional design method for mine haul roads and, through an analysis and quantification of existing wearing course material performance, to recommend appropriate wearing course material selection guidelines. The functional design technique has been applied at a number of mines and is illustrated by an application case study which demonstrates the potential reduction in total transportation operating costs associated with the optimal functional design.

Jan 1, 2000

Tracey Khanna, Assistant Editor of UK?s Mining Magazine discusses some of the new and important environmental challenges, physical and social, that are facing mining companies. The tide of public opinion has turned strongly against those companies which are unable to show that they are practising responsible environmental stewardship. This is, no doubt, in part due to the recent focus of the international media on environmental issues and constantly improving means of communications, which has brought the whole subject of mining and the environment to those who, in the past, had only a limited awareness of the industry. Mining companies today face new and important challenges with regard to the environment, both physical and social. New technology and a greater understanding of waste management techniques has helped to bring about improved handling and disposal of mines wastes, so reducing some of the impacts. However, improved technology has also brought about the economic viability of exploiting increasingly lower-grade ore from open pits, resulting in a greater visual impact.

Jan 1, 2000

By H. Aykul

The choice of which mining method to use at many large surface coal mines is often dicated by what machinery is available or what experience the mine management can offer. One of the most significant surface coal mines in Turkey is owned and operated by the Turkish National Coal Board, located to the west of the city of Kütahya. The Seyitömer Lignite Enterprise (SLE) extracts low quality coal, the majority of which is supplied to an adjacent power station. The coal seems at SLE contain bands of ash which under normal mining conditions are extracted with the coal. This increases the ash content of the run of mine coal and results in lower efficiency at the power station and financial penalties for SLE. In this paper, therefore, selection of the best possible equipment and production method was identified to achieve high selective mining at SLE. The research found that two different high selective mining methods were suitable for selective excavation of the B3 seam, which were hydraulic excavator and truck and surface miner and truck combinations. It was also found that high selective excavation could provide the desired coal quality at 52% lower costs when the whole process (excavation, transportation, processing, etc.) was considered. Keywords: coal mining, surface mining, selective mining.

Jan 1, 2007

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

Council for 2005/2006 President W.H. van Niekerk President-elect R.P.H. Willis Vice-presidents Senior R.G.B. Pickering Junior A.M. Garbers-Craig Immediate Past-president F.M.G. Egerton Honorary Treasurer J.A. Cruise

Jan 1, 2006

By M. E. Rossi

All large-scale applications of conditional simulations intend to benefit from the ‘correct’ (or’ accurate’) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. This paper discusses a number of relevant issues that highlight the extent to which, in reality, a model of uncertainty is dependent on the random function model chosen. Often in the presence of large number of conditioning data most available random function models will provide similar models of uncertainty. When conditioning is scarce, the resulting models of uncertainty will vary more widely, since the final output will depend mostly on the underlying assumptions of the model chosen. The application described in this paper is taken from a large porphyry Cu operation in northern Chile, and it demonstrates the impact of several variables on the resulting models of uncertainty. In particular, some of the decisions involved include the number of conditioning data and the underlying Random Function model used (Gaussian or indicator-based). Also, implementation-specific parameters must be decided upon, such as grid size used, random number generator, simple or ordinary kriging, multiple-grid simulation, and simulation of irregular three-dimensional bodies (as opposed to regular grids). Some practical guidelines are proposed to deal with these decisions.

Jan 1, 2003

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By J. M. Sabio, A. W. Stalberg

Keywords: Pyrometallurgy, furnace, calcium carbide, acetylene, Newcastle The manufacture of calcium carbide in Newcastle, South Africa, was started in the late 1950s by a company called South African Carbide, at the Ballengeich site. In 1978, this operation was bought by the forerunner to the present AECI Ltd, a large producer of commodity chemicals at the time. Production continued at this site until 1992. In the meantime, Karbochem, an operating division of Sentrachem Ltd, was also manufacturing carbide in Newcastle, as a building block for the manufacture of synthetic rubber. In 1990, the Karbochem calcium carbide operation was closed down. In 1992, the AECI carbide business and the Karbochem production facility were amalgamated, and production continued under the Karbochem name. In 1997, the Dow Chemical Company bought the holding company of Karbochem, and the carbide business continued operations until 2003. In June 2003, the business was sold to a management consortium as SA Calcium Carbide (Pty) Ltd. Later, in October 2004, 100% of the shares were acquired by the Andina Group. Today, the Andina Group, consisting of SACC from South Africa, CIL from UK, and ANDINA from Argentina, has become a global leader in the manufacture and supply of calcium carbide and calcium silicon, ferro silicon 75% and derivatives, recarburizers with low nitrogen content, acetylene, carbon black, micro-silica, and silicon metal. The production facilities at Newcastle comprise a 52 MVA submerged arc furnace of a closed design, carbon monoxide gas recovery, recovery of fine raw materials via a hollow electrode system, and an extensive computer-controlled process. These all enable an efficient state-of-the-art operation. The downstream processing facilities consist of screening and drumming facilities, milling facilities, an acetylene generation plant, and an acetylene carbon black plant. Clearly, SA Calcium Carbide (Pty) Ltd has a long history of supplying quality calcium carbide to the industries that it proudly serves.

Jan 1, 2006

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005