Search Documents

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

By Nobuzwe Makhotla, Sasha Boskovic, Steve Hearn

"Mineral separation efficiency in flotation depends, to an extent, on the type of frother used. Huntsman develops and manufactures unique frothers which are suited for mineral processing applications. This paper discusses the Huntsman approach to understanding the industry’s flotation frother requirements to optimise frother selection and introduce the Huntsman’s POLYFROTH® frother range. Specific case studies where the frothers are used are discussed. INTRODUCTION Froth flotation is a process of using bubbles to separate minerals based on their relative affinity for water. Bubbles are induced in the slurry through aeration. Chemistry is used to aid the flotation process and chemical reagents are added to enhance the separation process. The flotation reagents include frothers, collectors, surface modifiers and pH regulators that control physical and chemical conditions of solid, air and liquid phases, respectively. As described by Harris (1976), the key effect is that of bubble size control by way of preservation of the generated bubble size, which is attributed to the coalescence inhibition by the presence of the frother on the bubble surface. Following this, the frother must stabilize the froth phase. Frothers are also added to create optimal conditions for bubble creation and stability by decreasing the surface tension of the water. Depressants may be added, depending on the ore treated, to assist the hydrophilic particles to stay in the water phase. Clay particles may need to be dispersed to prevent them from attaching to the bubbles. Hydrophobic particles attach to the bubbles and are carried to the surface of the slurry where froth is formed. It is important for these bubbles to have the mobility to carry the mineral to the launder where the concentrate is collected. Types of Frothers There are generally three main groups of frothers used in froth flotation. Alcohol Type These frothers have a molecular structure that usually includes 5 to 8 carbon atoms in a hydrocarbon chain and their solubility in water is limited. Methyl isobutyl carbinol (MIBC) belongs to this category and is widely used in the industry. The weaker alcohol-type frothers are more selective and typically suited to finer particles. There are three sub-categories under this group: aliphatic, cyclic and aromatic alcohols."

Jan 1, 2015

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By H. Yilmaz

A testing method for assessing the shear-bond strength of thin spray-on liner (TSL) on rock substrate was developed at Wits University Rock Mechanics Laboratories. The gap between a 20 mm thick steel ring and a rock core is filled with TSL along the depth of the ring. After the curing of the TSL for a predetermined period, the sample is placed on a base, which offers support to the steel ring and the TSL but not to the rock core. A compressive load is applied on the rock core displacing the core on TSL contact and punching it towards the void in the support base. Shear-bond strengths for different TSL products as well as shotcrete were measured. This paper describes the test set-up and points out the important aspects and procedures during sample preparation and test execution. The test results are also presented and discussed.

Jan 1, 2007

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By N. Z. Jovanovic

Irrigation of agricultural crops may be a cost-effective option for the utilization of gypsiferous minewater as it may also create an opportunity to produce crops during the dry winter season on farm sin South Africa, such as in Mpumalanga. In this study, intensive field monitoring systems were developed and implemented to assess the feasibility and sustainability of irrigation with gypsiferous mine water. Soil water and salt balance components, as well as crop yields, were monitored in field trials carried out at Kleinkopjé and New Vaal Collieries (Anglo Coal), and at Syferfontein (Sasol). Field measurements indicated that high crop and pasture yields can be obtained, provided fertilization and irrigation water management are appropriate. Soil water and salt balances indicated that considerable amounts of minewater can be used and considerable masses of salts can be removed through precipitation of gypsum in the soil profile. With appropriate management, water and salt runoff and salt leaching can be intercepted, thereby minimizing the impact on groundwater. The SWB model is being validated through on-going monitoring. This will allow the use of the SWB model at other sites to predict the long-term impact of irrigation with mine water on soil and groundwater, as well as to run scenario simulations in order to recommend sustainable management of irrigation with minewater.

Jan 1, 2004

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By M. Seeger

The demographics and the growing numbers of people provide a strong signal that the demand for electrical power in Southern Africa will grow considerably over the foreseeable future. Without a steady and increasing supply of electricity development of the continent is likely to be constrained. The inventory of solar, wind, hydrothermal, geothermal and biomass resources will probably provide sources of energy for the future The parallels between extraction of natural resources in the minerals industry and the green energy industry is striking, and the well-established project development process in the minerals industry provides an ideal and useful template for comparing the establishment and development of green energy projects. The potential levels of power generation and carbon savings are described.

Jan 1, 2010

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004