Search Documents

By Thomas Varley

During the past few years, since flotation has become the paramount treatment method for most all kinds of ores, the Bureau has gathered the data on consumption of reagents used in the flotation treatment. The first report was issued in 1916. A brief review of such reports snows the progress made in the art of flotation, and each year brings forth the development of new reagent a or combinations of reagents that seem sure to survive, but research and progress spell their defeat, if not by entire elimination, at least subjects them to considerable modification.

Jan 1, 1928

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By R. Marshall

Electrical trailing cable handling techniques and practices used in metal and non-metal surface mines were investigated by obtaining information through actual visits to the mine properties located in a variety of geological areas and climatic conditions. An analysis was made of all accidents related to cable handling which are cataloged by HSAC* for the period from 1971, through June 1980. Information was also collected from mine operators concerning near accidents and non-reported accidents. The results of this investigation were presented to the U.S. Bureau of Mines in an effort to outline recommended practices for cable handling in surface mines and to recommend additions and/or changes in the present regulations now being enforced by MSHA** field inspectors. These recommendations are also intended to assist the U.S. Bureau of Mines in evaluating the need for assisting the mine operators in the areas of training and distribution of information related to material handling of trailing cable. * Health Safety Analysis Center ** Mine Safety & Health Administration

Jan 1, 1980

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Ernest A. Curth

The Bureau of Mines and Old Ben Coal Co. concluded a cost-sharing contract in 1975, the objective of which was to demonstrate the Herrin No. 6 coalbed in southern Illinois can be mined safely by longwall methods. Under the agreement, three longwall panels are to be mined at Old Ben No. 24 mine. A premining investigation laid the groundwork for specifying a roof-support system designed to control hazardous ground. Old Ben Coal Co. and Bureau engineers selected lemiscate-type roof shields. A rock mechanics program and geological mapping provide early warning capability and criteria for future equipment design. The effect of mining on the surface was monitored by a surface survey to develop subsidence-prediction criteria for the Illinois coal basin. The first of the three longwall panels started up in September 1976 and was completed in May 1977. The major adverse condition was the occurrence of limestone concretions, called coal balls, in massive pods. The shields provided adequate roof control even in faulty ground. Operation of the second panel started on August 1, 1977, following panel-to-panel transfer of the equipment. The accident rate was low.

Jan 1, 1978

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By L. J. Prosser, Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By Joseph A. Sutton

This study was undertaken by the Bureau of Mines to determine whether the sulfur-oxidizing bacterium Thiobacillus thiooxidans could use sulfur compounds to produce sulfuric acid in sufficient quantities to leach valuable metals from low-grade ores. The results of extended tests indicated that the bacterium is capable of extracting appreciable amounts of copper and cobalt from ore and mineral samples when sulfur is available in a state that can be readily assimilated by the organisms. Under the conditions of these tests, this organism was not able to assimilate and oxidize the sulfur as it occurred in the ores and minerals. Ores containing copper minerals in the silicate, carbonate, and oxide forms, in the presence of elemental sulfur, were more susceptible to bacterial action than ores containing copper minerals in the sulfide form. Thiobacillus thiooxidans remained active on elemental sulfur in the presence of some of the ores which were tested, but could not tolerate others. Therefore, strains of the bacterium were progressively adjusted to increasing concentrations (0.5 to 10 grams) of the individual ores until they could remain active on 10-gram portions of all ores being tested.

Jan 1, 1961

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982