Search Documents

By Launa Mallett, PhD, Charles Vaught, PhD

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

Enable mine personnel to determine the effectiveness of and to optimize the mine fire stench warning system without resorting to costly trial and error fire drills. Approach The mine fire stench warning system is used by underground metal/nonmetal mines to warn mine workers of a fire or other emergency. Stench is released directly into the mine ventilation and/or compressed air lines, and its repulsive odor warns miners to evacuate the mine or to follow other established emergency procedures. Unfortunately, since most deep metal mines have complex ventilation systems, some areas of the mine may receive nauseatingly high concentrations of stench while other areas, in more remote locations, may receive no warning or greatly delayed warring at best. The Bureau of Mines, through research, endeavored to solve this problem with a computer modeling system designed to calculate the distribution of odorant by the stench warning system.

Jan 1, 1986

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.

By R. V. Ramani, A. S. C. Owili-eger

The rapid depletion of shallower coal reserves dictate that mining in the future will be deeper and more complex with more difficult natural conditions. Consequently, an increase in methane emission is expected. It is becoming evident that more accurate predictions and better planning are necessary to design efficient methane drainage systems. This objective can be achieved by the utilization of the knowledge of the physics of gas flow through coal seams and rock strata and by the application of digital computers in the solution of methane flow problems. Although the methane emission models described here have not been adequately applied to existing field operations, good agreement between actual field measurements reported in literature and the simulation results indicates the potential of these models for initial flow quantity approximations and ventilation planning. This report has, therefore, introduced to the mine operator yet another application of computers as a planning tool. AREAS FOR FURTHER RESEARCH The study reported here is by no means complete. Extensive research efforts should be directed to the following areas: (a) Better understanding of the physics of gas flow through porous media which exhibit fracture permeability. (b) Determination of field parameters which control gas migration. (c) Investigation of the effects of the rate of penetration on the emission rate and fracture propagation.

Jan 1, 1974

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By Michael J. Sapko, Gregory M. Green, Harry C. Verakis, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of U.S. coal mines. The last comprehensive survey of this type was performed in the 1920’s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA’s ten bituminous Coal Mine Health and Safety Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920’s. The significance of these finer coal dust sizes is discussed relevant to the amount of rock dust required to prevent coal dust explosions.

By D. J. Parker

Du.ring the past two years a number of oases of successful first-aid treatn . .)nt have been reported by or through the employees of the O. s. Bureau of -anes safety cars and stations. Among such cases are the following: At Benbush, w. Va., a boy or 16 years of age who ba.d just started to work in the mines was trained in first-aid by the crew of Bureau of Mines car 8. The local rr.ine superintendent afterwards reported tba.t a few dS¥s later this boy, Melvin Hollingsworht, found droming in a spring a. baby about three years old who bad wandered away fron.. har.e alone. The boy rescued the baby and perf'oxmed artificial re­suscitation upon it, thu.s saving the child's life. The Schaefer method of resuscitation bad bean ta"Ugbt the boy as a routine art of the regular first-aid course.

May 1, 1922

"Reports are sometimes heard of one ill effects of pneumatic tools on the hands of workmen. In consequence of such reports, Dr. Francis M. Barnes, Jr., M..D. of St. Louis, Missouri, was retained by the operators to make an investigation of conditions in the Bedford, Indiana, region, and the result of this investigation was published the Journal of the Missouri State Medical Association, Volume 16, February 1919. A brief review of this report may be of interest to all users of pneumatic tools, or operators of plants where such tools are employed.The investigation was made during December 1917, and involved an examination of general working conditions, and a careful physical examination of stoneworkers who had long used pneumatic tools. As the Bedford district is the most important structural limestone producing center in the country, the results of this investigation may be regarded as fairly conclusive as to the general effect of pneumatic tools on limestone workers."

Jan 1, 1920

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

By T. E. Marshall, D. R. Dolinar, C. S. Cornpton, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

The U.S., Australian, and United Kingdom coal and the Canadian hard rock mining industries have long recognized the significance of high horizontal stresses as a factor affecting the stability of roof and rib conditions in underground mines. Recently, a growing segment of the U.S. underground stone mining industry has also begun to recognize that horizontal stresses occur in some of its more than 90 mines. Considering the typically high strength and massive nature of limestone, this fact is a revelation in itself. High horizontal stresses produce extensive and sudden rock failures and, in some cases, resulted in injuries to mine workers. Through the years diverse control strategies have been proposed and experimented with. Reorientation of mine entries to reduce stress concentrations have proven successful and are widely accepted in practice. Other solutions, like rock reinforcement, are poorly understood and less accepted in practice. It is the purpose of this National Institute for Occupational Safety and Health (NIOSH) study to develop a better fundamental understanding of these ground control strategies under high horizontal stress conditions through a series of field and laboratory studies. To this end a design technique is presented which provides stone miners with a method for making stability assessments. The consequences of widening rooms, changing geology and horizontal stresses, and different rock bolts on roof beam failures are discussed.

By Chas F. Jackson

 The annual reports of the supervising engineers of the several sections of the Mining Division are assembled herein and comprise the annual report of the division. During the year under review the work was oriented entirely to the war program by applying apparatus and technique previously developed in research directly to war problems, as well as by intensified search for and exploration of deposits of minerals necessary in the war.

Oct 1, 1942

By Arno C. Fieldner

In connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character of the coal and the value of the fuel in the public lands, many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The systematic collection and analysis of coal samples in connection with investigations of fuels was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geo- logical Survey for six years. Descriptions of the coal samples col- lected in connection with these investigations between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22. The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1911 to 1913. In order that the material in this bulletin may be used to supplement that presented in Bulletin 22, the same plan of geographical classification has been fol- lowed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1914

By Arthur E. Goddard

Radio propagation measurements were conducted in a coal mine at UHF (200 to 1000 MHz) and VLF (1 to 50 kHz) to characterize the transmission loss of intra-mine paths. The basic experimental parameters included frequency, polarization, path orientation and distance. Further tests evaluated the performance of roof-bolt vs. loop antennas at VLF and parasitic reflectors at UHF. Measurement results are summarized in a series of transmission loss curves. Examples are presented to show the use of these curves in predicting the performance of radio communication systems in mines.

Jan 1, 1973

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977