Search Documents

By D. B. Starkey

Investigation into the expressions of the field produced by a loop over a conducting half space or in an infinite conducting half space are well documented. Reasonably complex descriptions of the effects of stratification also are reported. However, a model which must contain all of these complexities because of transmission to depths of 15,000 feet and also include the pertibation of the field by a verticle cylindrical steel casing loses its facility in the field or for quick, accurate approximation to field magnitudes and phase. This paper describes the results of two field tests to determine the attenuation and phase versus depth and frequency of an electromagnetic wave (induction field). A simple two-layer model is postulated to predict the magnitude and phase of the induced field which does not require sophisticated computing tools. Correlation of the model with experimental results show agreement of most amplitude measurements to within 3 db and most phase measurements to within five degrees. The tests were conducted in a 7400 foot deep well in Nevada and an 11,000 foot deep well in Wyoming which had conductivities ranging from .0025 mhos/m to .25 mhos/m. The surface transmitting dipole had an area of ~ 10 6 feet squared and constant frequency signals of 1.5 Hz to 20 Hz were transmitted through the earth utilizing less than 65 watts of power. Model Description The magnetic field intensity components generated by a magnetic dipole immersed in an infinite homogeneous medium can be expressed in spherical coordinates as: [ ] where N, I, and (p a ) are the transmitting antenna turns, current, and effective area, respectively, and r is the range from the loops circumference to the measurement point. The case of interest for these experiments, however, is the special case of coaxial dipoles, i.e., ? = 180° . For this case H?= 0 and H reduces to: [ ]

Jan 1, 1973

By Donald N. H. Chi

This Bureau of Mines report is concerned with a theoretical study of the aerodynamic response of a single mine entry to flame-induced disturbance. The unsteady, one/dimensional, compressible flow equations were solved using the method of characteristics. This study was primarily undertaken to determine the feasibility of extending the method of characteristics to study the aero-dynamic response of complex mine networks. It was demonstrated that although the technique has merit in studying the complex wave interaction in single entries, it appears to be too unwieldly and too expensive for network analysis. Effort was also directed at a further study of the dispersion and filtering characteristic of aerodynamic disturbances in mine passageways.

Jan 1, 1975

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984

By A. R. Elliott

In the early part of the your 1919 the Bureau of Mines undertook a study of methods of handling oil after it had buon produced, with the view of pointing out the losses due to evaporation and other causes. Observations on present methods show that the oil is subject to largo losses in both quantity and quality from the time it loaves tho well until it is recoivod by the pipe-lina company. During this time it is splashed into four or more tanks of various sizes and with little or no protection over the tops. From the settling tank, where the flow of oil is tamporarily stopped in order to permit sparation of ter and sediments, through the gago tanks and leaso gathering tanks to the largo tank storage where it is hold for many days, rich gasoline vapors roadily escape, especially from tho ghor gravity oil. As no effort is made to measure the oil before it reached the storage tanks, where it is delivered to the pipe-line company, the lossos of the light products of the oil can only be approximated, and, as final results will show, are no doubt usually very much underestimated. In conducting this investigation, the Bureau has endeavored to make tests that would show quantities and values lost, in order to impress better upon those concerned what might be saved through a little more diligence. Eperiments were conducted on both California and Mid-Continent oils. The field operimental work done in California, on which a report is to be published in the near future, is cutlined briefly below: The field work consisted in collecting from operating companies data on storage of oils in large tankage and in performing experiments in the field on storing and piping oil to small lease tanks under practical conditions. Acourate Easurements were takon on the volume, gravity and gasoline content of the oil as it passed through the various stages in its removal from the lease. The work extended over the four seasons of the year in order to obtain better the effect of varying winds and high and low atmospheric temperatures during those periods. Thanks are due to the many oil operators who have taken a personal interest in the work and gave valuable information and assistance. One company furnished the oil and tanks and much of the apparatus and labor. This company also per- mitted the work to be done on its properties in the Coalinga field. This was of material aid, as the results were to be comparative and therefore it was necessary that the same gravity oil be used throughout the experiments.

Oct 1, 1920

By F. D. Osgood, A. C. Fieldner, W. A. Selvig

In connection with investigations being conducted by the Bureau of Mines regarding pulmonary disease which is prevalent among metal miners in certain districts , a large number of rock- dust samples have been collected , and have been examined in the Bureau's laboratories . The earlier work has been described in Bureau of Mines Technical Paper 105 , " Pulmonary disease among miners in the Joplin district , Missouri , and its relation to rock dust in mines " by A. J. Lanza and Edwin Higgins , 1915 , and in Bureau of Mines Bulletin 132 , " Siliceous dust in relation to pulmonary disease among miners in the Joplin district , Missouri , " by Edwin Higgins , A.J. Lanza , F.B.Laney , and Geo . S. Rice , 1919. The methods of collecting and examining dust samples have been greatly improved during the investigation , much valuable information having been made available by similar investigations conducted by the Miners ! Phthisis Prevention Committee , Union of South Africa . The latter are described in the " General report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1916 " , and " Final report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1919. " The investigations by the Bureau of Mines and the South African committee show that by prolonged inhalation of air containing minute particles of sharp and insoluble rock dust , the lungs retain sufficient dust particles to cause decided injury to the lung tissue , the injured lung becoming very susceptible to the development of tuberculosis .

May 1, 1920

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968

By H. H. Schrenk

[A calorimetric method3/ for the determination of benzene in amounts as low as 0.001 m has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel from the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations.]

Jan 1, 1935

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

Produce an annotated bibliography to serve as a comprehensive source of published information available on the use of soil amendments in coal mine reclamation and the characterization of coal mine soils. The Problem There is a substantial amount of information available tin coal mine reclamation and revegetation, particularly on the use of soil amendments to ameliorate site conditions and aid vegetation establishment, growth development, and productivity. Additionally, site characterizations based on chemical, physical, and mineralogical properties have been thoroughly researched. This information, however, is widely disseminated throughout various professional and scientific journals, State and Federal documents, proceedings of conferences, theses, and other technical writings. A critical need exists for a comprehensive and up-to-date summary of published information concerning the uses, methodologies, and types of soil amendments that arc necessary for reclamation success.

Jan 1, 1991

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By E. P. Youngman

The law now in effect (January 30, 1931) in the Netherlands with respect to the prospecting for and the developing of minerals is regulated by , or based upon , the French Act of April 21 , 1810 , "Concernant les mines , les minières et les carrières ( Bulletin des Lois No. 285) . " A second edition of a compilation ( by Drs . Ccuvee and Ritter ) of the mining legislation of Holland , including this act with other legal requirements , was published in 1928 under the title of "De Nederlandsche Mijnwetgeving , " by H. T. Tjeenk Willink & Zoon , Haarlem. In this abstract reference is made to the Act of 1810 , the Royal Decree of September 18, 1818 , the Mining Act of 1903 , and the Act of June 20 , 1924 .

Aug 1, 1931