Search Documents

By Nicholas P. Kripakov

The U.S. Bureau of Mines examined the applicability of existing material models to solve practical geotechnical mining-related problems by solving a yielding pillar stability problem considering confining effects on strength. Numerical difficulties normally encountered with modeling strain softening behavior were eased with a simplified computational procedure using a quasi-elastic approach to account for residual strength after initial failure. Although in agreement with a confined-core pillar design method using actual mine conditions that include mine layout geometry, overburden geology, and rock properties of the deposit and surrounding structure, the results cannot be verified because measured field data are not available at this writing.

Jan 1, 1981

By C. Travis Anderson

"A recent critical study by Ralston3 of the iron system points out the importance of and necessity for work upon the preparation of ferrous oxide. Not only are ferrous oxide samples desired for determination of the important physical and chemical properties, such as specific heats and heats of formation, bat also information on the stability and behavior of this material is of considerable technical importance. Related. problems where the properties of Fe0 are important have to do with desulphurization of iron, the formation and occurrence of magnetite in copper smelter slags, and sulphur elimination in copperFerrous oxide also has valuable catalytic properties, as is demonstrated in nitrogen fixation.Pure ferrous oxide has never been prepared in quantities large enough to furnish adequate physical and chemical data on its properties. Only two or three experiments4 have produced a fraction of a gram in a state approximating purity and have collected evidence that has been sufficient proof of their having done so. Ferrous oxide is stable only above about 570°C., and below that splits into magnetite and iron according to the reactionUp to about 1920, those who had endeavored to prepare FeO made no provision for rapid chilling, so that although their product. may have had the proper iron oxygen ratio for FeO, in reality it-probably did not consist of pure FeO. The above reaction is reversible; above 570oC. magnetite and iron are supposed to recombine almost completely, and if so, should constitute a direct and easy method of preparation. The data, however, were somewhat conflicting, and the extent to which the reaction goes in either direction needed checking. Preliminary experiments on the interaction of molten Fe304 with solid Fe gave Fe0 of about 85 per cent purity, corresponding to. the approximate purity obtained by some previous investigators. The present work is concerned chiefly with the results cf repeated interaction between partly reduced magnetite and iron, and the calculations which may be made from such results. Repeated treatments are necessary, because molten impure ferrous oxide and iron can not be kept in contact for more than short periods of time."

Oct 1, 1928

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals4/ and. investigations of their chemical and physical properties.5/ The coal represented by the sample from weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By Jon K. Ahlness

The Bureau of Mines, in cooperation with the Institute of Mineral Research of Michigan Technological University, and the Upper Great Lakes Regional Commission, conducted an investigation of electronic sorting of native copper ore from Upper Michigan. This report is based on research by the Institute of Mineral Research under contract to the Bureau. The test program evaluated the use of belt and rotary sorters on various size and grade fractions of ore. Both plant-scale sorting and lab sorting tests were run. The plant sorting objectives were to determine the sortability of different ores and the efficiency of the electronic ore sorters. High-and low-grade ores from both conglomerate and amygdaloid types were separated into four size fractions. The two larger sizes were sorted on belt sorters and the two smaller ones on rotary sorters. Copper recoveries ranged from 20.0 pct from a feed grade of 0.40 pct to 80.3 pct from a feed grade of 1.08 pct. Lab sorting tests of conglomerate ore were run to determine the efficiency of a belt sorter equipped with a second sensing coil located above the belt and to determine the sorting characteristics of larger ore size fractions than those used in the plant sorting. Copper recoveries from the combined feed sizes ranged from 47.0 pct from a feed grade of 0.13 pct to 96.8 pct from a feed grade of 4.87 pct. For all the ore types except one, it was found that the copper recovery increased with the feed size.

Jan 1, 1980

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By R. Van A. Mills

[In previous contributions** the writer has called attention to important relations that faulting bears to the migration and accumulation of oil end gas. It has been pointed that favorably situated parts of oil and gas bearing, sands have been enriched by migration art segregation incident to faulting. The escape of water through natural passages such. as fault fissures has induced wide spread hydraulic currents through the beds toward these, points, of diminished pressure and these water currents, plus buoyancy hove contributed largely toward the migration of oil to favorable rock entrapments in the vicinity of the faults.*** The propulsive force of expanding gas has been one of the contributing causes for the hydraulic currents. Paradoxical as it may seem, the escape of gas with entrained oil through fissures has been on important factor In the migration, and accumulation of oil in many faulted areas. Compressed gas is the propulsive force by which oil generally moves to producing wells. It is also one of the propulsive forces by which oil has moved with or even ahead of water under conditions: of differential pressure brought about by faulting.]

Jan 1, 1922

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By Thomas P. Holden, Todd M. Ruff

Problem: An average of three workers a year are killed in surface mining operations when a piece of haulage equipment collides with another smaller vehicle or a worker on foot. Another three workers are killed each year when haulage equipment backs over the edge of a dump point or stockpile. Devices to monitor the blind areas of mining equipment are needed to provide a warning to operators when a vehicle, person, or change in terrain is near the equipment. Method: A proximity warning system (PWS) based on the global positioning system (GPS) and peer-to-peer communication has been developed to prevent collisions between mining equipment, small vehicles, and stationary structures. Results: A final system was demonstrated using one off-highway haul truck, three smaller vehicles, and various stationary structures at a surface mining operation. The system successfully displayed the location of nearby vehicles and stationary structures and provided visual and audible warnings to the equipment operator when they were within a preset distance. Summary: Many surface mining operations already use GPS technology on their mobile equipment for tracking and dispatch. Our tests have shown that it is feasible to add proximity warning to these existing systems as a safety feature. Larger scale and long-term tests are needed to prove the technology adequately. Impact on Industry: A PWSs that incorporates a combination of technologies could significantly reduce accidents that involve collisions or driving over an edge at surface mining operations.

By Edmond Chin

Mineral production was of minor importance to the country's economy, and Bangladesh was not a ranking world producer of any mineral commodity in 1980. Natural gas was the most important mineral exploited, and reserves were sufficient to allow a significant increase in its use. A greater proportion of the domestic heat and electrical energy needs could be filled by increased production and distribution of natural gas. Also, the export of natural gas was feasible either by pipeline to India or in the form of liquefied natural gas (LNG). Some nonmetallic minerals could be developed, as well as coal and peat, given sufficient capital investment. Bangladesh's strongly agricultural economy made fair progress in 1979.80.1 The major harvest of November-December 1979 turned out to be better than had been anticipated after an early drought left poor planting conditions. Secondary crops (harvested in February-March 1980 and June- July 1980) were excellent. There were prospects for a record harvest in fiscal year

Jan 1, 1982

By D. E. Seizinger

The Bureau of Mines has developed analytical methods, primarily gas chromatographic, for measurement of exhaust oxygenates produced from selected simple fuels. The resulting data were used to estimate levels of carbonyls and noncarbonyl oxygenates in exhaust from gasoline fuels. Estimated noncarbonyl oxygenates in gasoline exhaust may comprise as much as 30 pct of total oxygenates which include unsaturated carbonyls and noncarbonyls believed to be significant potential pollutants.

Jan 1, 1972

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free- port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By R. V. Ramani, C. B. Manula, A. Owili-Eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMRC, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. These applications were developed initially as a part of the instructional material for the course Mng 422, "Mine Ventilation and Air Conditioning" at the Department of Mineral Engineering, The Pennsylvania State University. This ventilation simulator was developed under contract from the Department of Environmental Resources, formerly the Department of Mines and Mineral Industries, Commonwealth of Pennsylvania.

Jan 1, 1975

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By R. V. Ramani, A. S. C. Owili-eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. Part of the research reported here was originally done on a grant from the Department of Environmental Resources, Commonwealth of Pennsylvania and reported in Special Research Report No. SR-95 (February 25, 1973) of the Coal Research Board, The Pennsylvania State University.

Jan 1, 1974

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973