Search Documents

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies It discusses the concept of stress, Critical Incident Stress in emergency responders, and intro¬duces the Critical Incident Stress Debriefing (CISD) process. It is suggested that in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers and more universally, to those responsible for developing emergency management plans.

Aug 1, 1998

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

Provide minx operators with means for evaluating dust generation and bit wear effects on Production without costly and extensive underground testing. Approach Develop personal-computer-based cutting system models that will simultaneously evaluate machine, Coal seam, and mine-operator-controlled parameters for their interactive effects on dust generation, bit wear, and Production by either a longwall shearer or a continuous miner. How It Works CSM Programs have been developed to analyze relative dust generated by a double-drum, ranging arm, longwall shearer and a continuous miner. These interactive programs Provide relative dust, culling forces, and production values for any given set of mining machine parameters, specific seam conditions, and operator-controllable parameters. Expanded versions of each program provide a dynamic evaluation of the effects of bit wear, over time, on production.

Jan 1, 1989

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

By John W. Frey

This paper presents one of a series of digests of foreign mining legisla- tion and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Trinidad has been prepared from the best information available in ashington but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Sep 1, 1930

[ ]

Jan 1, 2011

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By M. H. Stanczyk

Bench-scale laboratory tests were made by the Bureau of Mines of a segregation-flotation concentrate, assaying 20.43 percent copper, to investigate the influence of various ratios and concentrations of ammonia and carbon dioxide on copper extraction. Leaching the concentrate with a solution containing 900 pounds of ammonia and 360 pounds of carbon dioxide per ton of feed, followed by washing the leach residue with 1.75 tons of a 10-percent solution of ammonium carbonate and about 1 ton of water (as steam) per ton of solids, resulted in a copper recovery of 96.3 percent. Resegregation and flotation tests of the washed residues revealed that 85 percent of the copper in the residue could be recovered. Steam distillation tests of a typical ammoniacal leach liquor, assaying 39 grams copper, 105 grams ammonia, and 77 grams carbon dioxide per liter, recovered over 99 percent of the copper as a mixed oxide-carbonate precipitate. The ammonia losses in leaching, filtering, washing, and distillation were 0.12 pound per pound of copper recovered in the precipitate. Calcination and subsequent hydrogen reduction of the precipitate yielded a metallic copper powder assaying 98 percent Cu, 0.87 percent Si02, 0.10 percent MgO, 0.54 percent CaO, and 0.41 percent R203.

Jan 1, 1961

By Ronald D. Hill, Elmore C. Grim

The cost of reclamation can vary widely, depending on the primary objectives of the restoration activities. statistics in this study originated from State files, publications, and personal communications relating to restoration and pollution control measures for previously mined lands (orphan lands) and active mines. Reclamation of orphan lands is generally considered a public burden and constitutes an economic problem. All work reported here was completed under government contract, by the lowest bidder, with money coming from State and/or Federal funds. Cost would have been substantially lower had the reclamation been concurrent with mining. Several persons connected with some of the projects have observed that costs could probably be reduced by at least one half, if the reclamation had been conducted along with the mining. The expense of clearing and grubbing of volunteer vegetation, disposal of buried trees and brush, loosing of compacted spoil, and re-establishing access to areas could be saved. In addition, a contracting firm doing the work for a government agency would have mobilization costs and receive a profit. Mining companies also are profit conscious and would consider these costs in anticipating their profits (e.g., overhead would be less if reclamation is integrated with mining). The data presented here should serve as a guide for estimating and determining cost ranges, however, it should be recognized that variations exist. Adjustments may be necessary from the standpoint of physical conditions, economic conditions, price changes, and more restrictive requirements of recent surface mining laws. Reclamation conditions, procedures and successes in the eastern United States, particularly in Appalachia, have no bearing on conditions to be expected in the western United States. The situations are wholly different. Reclamation in the West differs from th t in the East, primarily because of aridity especially a during the summer months 1). Because of the many variables and differences between reclamation in eastern and western areas, they will be discussed separately.

Jan 1, 1974

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFT test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 5, 1986

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Since 1990 and the publication of the Ergonomics Program Management Guidelines for Meatpacking Plants by the US Occupational Safety and Health Administration, numerous reports of companies implementing ergonomics program have been published. However, despite these numerous reports, no examples of implementing an ergonomics program in the mining industry have been reported. In 2000, NIOSH initiated a long-term project to demonstrate the implementation of an ergonomics process designed to identify and reduce exposures to ergonomic risk factors found in mining. The mine selected for this project was the Jim Bridger Mine, a surface coal mine located 35 miles northeast of Rock Springs, Sweetwater County, WY. This paper discusses how a large, surface coal mine implemented an ergonomics program and the lessons learned while doing so.

By H. A. Doerner

The Rare and Precious Metals Station of the U. S. Bureau of Mines has investigated several cases in which widely divergent amounts of molybdenum were reported by a number of custom laboratories to which quartered portions of the same sample had been sent for analysis . On an oxidized lead ore containing considerable vanadium and a little molybdenum , the amount of the latter reported ranged from 3.14 to 0.24 per cent M003 . The high results were due to the fact that vanadium was estimated with , and reported as , molybdenum . When analyzed by the method described in this paper , 0.15 per cent Moog was found, which is a fair agreement with the lowest figure previously reported . In another and more unusual example , a fine- grained rock containing considerable graphite was submitted for analysis . As a white residue could not be obtained by treating this material with acid , several chemists decomposed the ore by a prolonged fusion with soda ash and nitre and leached the melt with hot water in crder to insure the dissolution of any and all the molybdenum present . After precipitating and filtering the silica from the solution , acetic acid , ammonium acetate , and lead acetate were added to precipitate lead molybdate . The solution contained phosphorous derived from the ore , which precipitated as lead phosphate . The latter was mistaken for , and reported as , molybdenum. As two different chemists used essentially the same procedure , their results , although incorrect , checked . Other chemists using different methods found no molybdenum . From these and other instances it is evident that reputable and conscientious assayers may make serious errors in determining molybdenum, and even duplication of results by different chemists does not necessarily insure against error . The elements most likely to cause trouble are vanadium, tungsten, uranium , arsenic , antimony , titanium, tin , phosphorous , and chromium . The precautions necessary to eliminate these and other impurities vary with the type of ore and the method of analysis . Most texts present methods of limited application and omit or fail to emphasize adequately such precautions . No one method can be given that will best fit every case , but the following procedure has been selected as being the simplest reliable method for such occasional determinations of molybdenum in an ore as are encountered in customs work.

Sep 1, 1930

"The major thrust of this research is directed towards a better undstanding of the behavior of airborne dust particles in underground mine airways. Figure 61 shows a schematic of dust flow in mine airway. The work included development of a mathematical model of dust behavior in mine airways, experimental study of the behavior of dust clouds and comparison of computer model output and experimental results. Re-entraiment is a secondary source of dust in mine airways and factors affecting re-entrainment are being identified.Investigations have encompassed both experimental and theoretical research into the behavior of dust in mine airways. Experiments were performed in mine airways under both controlled and normal operating conditions (Figure 62). The controlled experiments included the documentation of the concentration and desposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using real-time aerosol monitors (RAM-1) (Figure 63).On the theoretical front, a convection-diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion. Comparative analyses of results of the controlled experiments with the predictions of the mathematical model were carried out. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion were examined in light of the experimental observations."

Nov 1, 1988

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Gerald A. Munson, E. P. Barrett

Rapid and accurate estimation of the proportions of mineral in rock mix- tures is essential in mineral-dressing research and industrial operation. Estimation of the proportions of potash and soda feldspars in ground pegmatite material by casual observation is almost impossible and may be tedious or even difficult by petrographic examination. Chemical analysis may not be an accurate measure, as pegmatite rock may contain the following minerals:

Jul 1, 1947

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985