Search Documents

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By L. B. Pankratz

Enthalpies above 298° K were investigated for four crystalline sodium borates by copper-block drop calorimetry. Determinations were made to 1,200° K for NaB02, 1,003° K for Na2B407, 1,005° K for NaB305, and 1,046° K for Na2Be013. No phase transitions or other thermal anomalies were found. The enthalpy determinations, when combined with known heats of formation at 298° K and other supplementary data, enabled the calculation of the heats and free energies of formation of the compounds to their melting points. Values of relative enthalpies, entropies, heat capacities, free energy functions, enthalpies of formation, free energies of formation, and equilibrium constants of formation were tabulated at even temperatures.

Jan 1, 1971

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By J. D. Hadden, Albert Sainato

The Bureau of Mines conducted drilling studies in the Pocahontas No. 3, the Pittsburgh, and a western coalbed to establish the gas migration characteristics for each. Gas pressures in the Pittsburgh coalbed were about 260 lb/in2 and in excess of 550 lb/in2 in the Pocahontas No. 3. Caving in drill holes prevented pressure measurements in the western coalbed. The Pittsburgh coalbed contained intersecting "clay veins" which formed gas pres- sure cells. Although these geological features hamper mining, they can be used to control the flow of methane into a mine working. Methane control techniques are proposed for the Pittsburgh and Pocahontas No. 3 coalbeds.

May 1, 1969

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By C. W. Owings

Recent recommendations of the Bureau of Mines regarding, rock dusting to prevent dust explosions in coal mines have been issued as Mine Safety Board Decision 32 and printed as Information Circular 7109.5/ The last paragraph on page 2 of I. C. 7109 states: After a mine or any part of a mine has been rock-dusted, samples of dust for analysis should be taken from the floor, ribs, roof, and timbers at such intervals of time as will give apple warning of need far redusting in order to maintain the required minimum percentage of incombustible in the mine dust. Details of the methods of sampling and analysis are given in Bureau of Mines Information Circular 7113.

Jan 1, 1940

By John P. Powell, J. L. Eakin

"INTRODUCTION AND SUMMARYNowata County, in the northeast corner of Oklahoma, is one of the principal oil-producing counties of this stripper area. Many fields in the county were opened and much oil was produced before statehood. The location of the major fields, as defined by the Oklahoma Corporation Commission, 2/ the outline of the areas of water-flooding activity, and the location of the several projects described in detail in this report are shown in figure 1.There was some drilling in the county earlier; but it was not until after 1904, when the Secretary of the Interior confirmed as valid the leases granted by the Cherokee Nation, that the major drilling activity began. Initial development in this part of Oklahoma was in the Chelsea field in Rogers County, which adjoins Novata County on the south. The activity spread rapidly northward to the Alluwe and Coody's Bluff fields, and then to the Nowata-Claggett field. Continued exploration resulted in discovery of the Delaware-Childers field, where some wells having an initial production of 1,000 barrels daily were completed. Fields discovered and developed during the next few years included the Lenepah (Elliott), Adair, California Creek, Curl Creek, Woody, and South Coffeyville. The oil-production history of Nowata County is shown in figure 2. In assembling the data for a production curve, it was found that the combined production records for Nowata and Rogers Counties were available for 1914 to 1951, inclusive, and that records for the individual counties were available only from 1926 to 1951, inclusive. The early production figures for the counties from 1905 to 1914, inclusive, except for 1909, were calculated from the initial production statistics of the Federal Geological Survey mineral resources bulletins and production data assembled by C. H. Beal. 3/ The production values for 1905 to 1926 for Nowata County were obtained by dividing the total production for the two counties by a percentage factor derived from known facts regarding the oil industry in the area. Production figures for the individual counties from 1926 to 1933, inclusive, were obtained from the files of the Oil and Gas Journal, and the figures from 1933 through 1951 were obtained from monthly reports of the Oklahoma Corporation Commission."

Jun 1, 1952

By Eugene T. Sheridan

This report presents data on individual plants of the fuel-briquet and packaged-fuel industries that were circularized by the Bureau of Mines, United States Department of the Interior, in its annual survey for 1958. Only plants that processed fuels of mineral origin were included; specifically, plants that manufactured briquets from charcoal were excluded. Fuel briquets and packaged fuel are manufactured by mixing fine-sized fuels with binders and compressing into small individual shapes. Both are used mainly for residential heating in the United States, but they differ considerably in appearance and physical characteristics. Briquets usually are produced as small, pillow-shaped forms, 2 to 4 inches in length, weighing from 2 to 4 ounces. Pack-aged fuel consists of 3-to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. Briquets are made with a water-insoluble binder and are designed for rough handling and outdoor storage, whereas packaged fuel generally is made with a water-soluble binder and must be stored indoors to prevent deterioration. Briquet plants are relatively large and usually are at mines or in dock areas where large quantities of fine-sized fuels accumulate. Packaged-fuel plants are smaller and are used chiefly by retail dealers to convert locally available coal and coke fines into a product that can be burned efficiently in residential beating equipment.

Jan 1, 1959

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

A computer model of an existing mine ventilation system can be executed using data developed from ventilation survey results. This model can then be used to analyze and evaluate proposed modifications to the system. The acquisition of field measurements during a ventilation survey and the corresponding development of this information into computer input data have been discussed in detail in the preceding chapters. In this chapter, the data are used in computer-oriented analysis of the mine ventilation system. The PSU/MVS was selected for use because of its advanced capabilities. MINE DESCRIPTION The mine chosen for this application is located in Western Pennsylvania. The Pittsburgh coal seam, having an average height of 5-1/4 to 6-1/2 ft, is mined under approximately 300 to 500 ft of cover. The mine preparation plant and shipping facilities are located at the seam outcrop along a river; mining has progressed from the outcrop to an area about 10 miles from the pit mouth so that there are extensive worked-out areas through which access is maintained to the current mining area. Coal haulage is by conveyor to an underground transfer point, located four miles from the pit mouth, and then by high speed rail haulage to the preparation plant. The rail haulage link is scheduled for replacement by a conveyor in the near future. Mining at the present time is limited to the room and pillar method using continuous miners. Longwall mining had been attempted in the past with only limited success; as a result, several panels originally laid out for longwall mining are currently being extracted by room and pillar work. The

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Computer input data for an operating mine is developed on the basis of a detailed ventilation survey which includes air quantity, air quality, pressure loss and fan performance measurements. Quantity measurements must be reviewed extensively and assumptions made about leakage quantities and airflow paths. Pressure measurements must be reviewed and developed into a pressure gradient for the mine system. Air quality measurements are used to determine methane sources and amounts. Finally, the fan test data is used to develop the correct fan characteristic curve. Quantities and pressure losses for each branch in the system are used to calculate the branch resistances which are then utilized in the ventilation simulator to model the mine system. QUANTITY BALANCE The quantity of air coming into a mine based on field measurements will rarely equal the quantity exiting the mine, even if allowances are made for methane or compressed air input to the system. The same statement can be made for airflow through any isolated part of the mine ventilation system such as individual working section or main aircourses leading to an area isolated from the rest of the mine. The reason for the apparent discrepancies is the accuracy of the indicated quantities which in turn is based on the accuracy of the individual velocity and area measurements. Even with measurements following the guidelines described in the previous section on quantity measurement, this error can only be minimized but not eliminated. As a result the ventilation system must be carefully balanced so that, for any loop, the quantity in plus any methane or compressed air injection will equal the quantity out. The continuity of flow described by the balanced system must approximate the

Jan 1, 1977

By Geo S. Rice

"The most authoritative compilations on the coal resources of the British Isles are given in ""The Coal Resources of the World"" issued by the 12th International Geological Congress, 1913. The reserve, calculated to a depth of 6,000 feet, in seams containing not less than two feet of merchantable coal are as follows: Mining at present is conducted at depths from about 800 to 3500 feet. The shallower coals have largely been exhausted. The present average hoisting depth probably is about 1500 feet.The thickness of individual beds at present mined varies from about 2-1/2 feet up to 40 feet in thickness, the latter thickness being found in North Staffordshire. The coal is rarely found level, but is approximately level in some parts of Yorkshire. Anthracite is mined in limited quantities in Wales, and Wales also produces a very high grade semi-anthracite or smokeless coal, which is fa famous the world round, and is equaled only by the Pocahontas and New River coals in the United States:As concerns the methods of mining, these vary widely according to the pitch of the bed, the thickness of coal, and natural conditions, but the prevailing method is some form of longwall or semi-longwall, by which all the coal is extracted. The other principal method is a so-called pillar and, stall method, by which the coal is mined out, leaving square or rectangular pillars which are extracted on the retreat, making it virtually, a retreating longwall system. This method is applied where the roof is strong, and particularly in the thicker beds, as the longwall method is not so well adapted for mining where the thickness exceeds five or six feet, unless it is what is called a multiple seam, one in which there are partings of rock that provide material for building walls, which the roof in subsiding gradually squeezes down."

Jul 1, 1920

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995