Search Documents

By H. Kenworthy

The investigations described in this report were undertaken to demonstrate, on a laboratory scale, the possibility of recovering several million pounds of tin plus tungsten contained in stockpiled and currently rejected slags from the Longhorn tin smelter at Texas City, Tex. At the same time, it was anticipated that the treatment procedures developed might be applicable to slags from other tin-smelting operations. Results of the laboratory work show that it is possible, by pyrometallurgical means, to separate the tin and tungsten into products of intermediate grade that may be returned to the smelter circuits for further upgrading. Several methods of treatment were investigated. The methods that proved effective were: Fusion reduction, chloride volatilization, sulfide volatilization, and carbide formation. Over 90 percent of the tin and tungsten could be removed from the slat by any of these methods. Each type of treatment has advantages and disadvantages, and it could not be determined from the small-scale work which method was the more meritorious. Tungsten and (in some types of treatment) tin-bearing products were diluted by iron, the separation of which will require additional studies. Prevention of a portion of the iron from reporting with the tin or tungsten is a distinct advantage and possibility that will require inure laboratory work to develop the needed techniques for its accomplishment. Tin products from single treatments of stag ranged up to 75 percent in tin content but were more generally under 35 percent. Tungsten products were usually under 15 percent; but segregated portions could be selected, at a sacrifice in recovery, that contained up to 50 percent tungstic oxide equivalent.

Jan 1, 1957

By R. D. Currie

"INTRODUCTION Compressed air for operating coal-mining equipment is seldom considered in conjunction with modern methods and appliances. But the Jamison Coal & Coke Co. has proved the economy and efficacy of compressed air for this purpose at its Mine 8 near Farmington, 8 miles west of Fairmont, Marion County, W.. Va., and the mining industry as a whole concedes its superior safety in gassy or dusty coal mines.The uses for compressed air in coal mining are now generally associated with such equipment as coal punchers, chain-breast machines, and to a lesser extent the ""radialaxe"" type of mining machines.Electricity has rapidly superseded compressed air for power in coal mines during the past 20 years; and in the last few years the general, and often unwise, use of electricity at the face region has taken on added impetus through the widespread use of mechanical loading equipment.Some of the unfavorable results of this increased use of electricity are shown in the growing number of mine explosions and fires of electrical origin. In the past four years 59 explosions of this type took the lives of 672 men, or 74.8 per cent of the total number of deaths from explosions were due to explosions of electrical origin.3In 1926, an explosion in Mine 8 of the Jamison Co. killed 19 men. The exact source of ignition was not determined, although it was definitely decided that it was of electrical origin and probably was at an electric coal-cutting machine.Prior to this disaster the company had done some experimenting with compressed-air-driven mining machines, and its Mine 9 had been completely equipped with air-driven chain-breast machines; a few of these machines were also in use in Mine 8. The explosion, however, gave impetus to the adoption by this company of compressed air for operating face equipment. The chain-breast machines were as satisfactory as electric machines of the same type; but the trend in the industry was toward faster cutting machines, which required less physical exertion on the part of the operating crews. A track-mounted machine of the arcwall type was found to be suitable for the conditions and system of mining, so that one of these operated by compressed air was developed by the Jeffrey Manufacturing Co. working with the officials of the Jamison Co.The first of these machines was installed in the latter part of 1926 and additional machines were delivered from time to time, until at present there are nine of them in the mine. Necessary improvements have been made, with the result that a fast-cutting, easily handled, efficient, and safe mining machine has been developed for cutting the hard Pitts¬burgh bed coal of the Fairmont field."

Oct 1, 1932

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

By A. L. Johnson

In this Bureau of Mines report, time-resolved infrared emission spectra and corresponding pressure and temperature histories are reported for large-scale propagations of CH4-air, CH4-air-N2, and CH4-air-CF3Br ignitions in a 12-ft-diam sphere. Absolute spectral radiances were obtained throughout combustion over the 1.6- to 4.8-gym range, and the radiance growth patterns for the H20 (2.5-µm) bands are presented as a function of methane stoichiometry and diluent concentration. Flame temperatures were determined from the C02-band emissions, which approximated unit emissivity shortly after ignition. Burning velocities are also given for some of the test-mixture compositions. Measured flame temperatures were in excellent to fair agreement with theoretical adiabatic values for the CH.-air and CH4-air-N2 mixtures; the best agreement was for the stoichiometric CH4-air mixture. The CH4-air-CF3Br mixtures with =2 pct CF3Br gave poor agreement with theory. The measured temperatures were significantly lower during the early stage of combustion; furthermore, the later stage of combustion was uninhibited and yielded unexpectedly high pressures. Supplemental data from a 2-ft-diam sphere at various initial pressures confirmed that the CF3Br inhibition effectiveness decreases with increased pressure. The possible effects of buoyancy, turbulence, and changing kinetics are discussed.

Jan 1, 1977

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in numerous applications. Normal Accident Theory (NAT) explains that these accidents are inevitable because of system complexity. Complex systems, such as computer-based systems, are highly interconnected, highly interactive, and tightly coupled. We do not have a scientific methodology to identify and quantify these complexities; specifically, NAT has not been operationalized for computer-based systems. Our research addressed this by operationalizing NAT for the system requirements of safety-related computer systems. It was theorized that there are two types of system complexity: external and internal. External complexity was characterized by three variables: system predictability, observability, and usability -the dependent variables; internal complexity was characterized by modeling system requirements with Software Cost Reduction dependency graphs, then quantifying model attributes using 15 graphtheoretical metrics the independent variables. Dependent variable data were obtained by having 32 subjects run simulations of our research test vehicle: the light control system (LCS). The LCS simulation tests used a cross-over design. Subject perceptions of these simulations were obtained by using a questionnaire. Canonical correlation analysis and structure correlations were used to test hypotheses 1 to 3 - the dependent variables predictability, observability, and usability do not correlate with the NAT complexity metrics. Five of 15 metrics proposed for NAT complexity correlated with the dependent data. These 5 metrics had structure correlations exceeding 0.25, standard errors < 0.10, and a 95% confidence interval. Therefore, the null hypotheses were rejected. A Wilcoxon signed ranks test was used to test hypotheses 4 to 6 - increasing NAT complexity increases system predictability, observability, and usability. The results showed that the dependent variables decreased as complexity increased. Therefore, null hypotheses 4 to 6 were rejected. Lastly, this work is a step forward to operationalize NAT for safety-related computer systems; however, limitations exist. Opportunities addressing these limitations and advancing NAT were identified. Lastly, the major contribution of this work is fundamental to scientific research - to gain knowledge through the discovery of relationship between the variables of interest. Specifically, NAT has been advanced by defining and quantifying complexity measures, and showing their inverse relationship to system predictability, observability, and usability.

By I. A. Jacobson

In a closely controlled laboratory retorting system for oil shale, a relationship was developed by the Bureau of Mines between the temperature in the retort and the weight ratio of ethylene to ethane in the gases produced. Reciprocal temperature was shown to be directly proportional to the log ([ethylene]/[ethane]). From this relationship a number, called retorting index, was developed. The retorting index has the dimension of temperature, but its magnitude depends on both temperature and residence time for the reactants in the heated zone in the oil-shale retort. The slopes of the lines relating reciprocal temperature and the logarithm of the ethylene-ethane ratios are nearly constant for each of the retorting processes for which data have been presented. The retorting index should be a valuable tool to control the operation of oil-shale retorts, either aboveground or in situ. If an optimum operating condition can be established, the maintenance of the optimum or the departure from it should be easily monitored by use of the index.

Jan 1, 1974

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a &apos;cascading pillar failure&apos; (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure&apos;, `massive pillar collapse&apos;, &apos;domino-type failure&apos; or &apos;pillar run&apos;. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes&apos; that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By Larry Patts, Michael J. Brnich

Approximately 45% of U.S. coal is produced from underground mining. The use of diesel engines to power under- ground mining equipment has steadily increased over the past four decades in an effort to improve mine safety and productivity. Several advantages realized with the use of diesel-powered mining equipment in underground coal mines are listed in Table I. The primary disadvantage of using diesel equipment in underground coal mines is that diesel exhaust emissions can contaminate mine ventilation air. The major constituents of diesel exhaust are gaseous emissions (which include carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons) and diesel particulate matter (DPM). The Mine Safety and Health Administration (MSHA) has incorporated threshold limit values for all gaseous components of diesel exhaust into their regulations. These have been established by the American Conference of Governmental Industrial Hygienists.

"Health standards in the U.S. are among the highest in the world. Achieving these standards have often had an impact on productivity, slowing output, and raising prices to levels that make it difficult to compete with many foreign industries. The answer to many of these problems lies in the development of new and advanced control techniques. This overview has identified some of the major respirable dust technological hurdles that have been overcome, and provided some insight into current and future approaches underway to remove these obstacles and to provide the United States with the most advanced state-of-the-art mining industry in the world from a respirable dust standpoint. The necessary developmental research is costly and time-consuming. The long-term, high-risk aspects of this effort are being addressed by the Bureau and the Generic Center on Respirable Dust, with support by industry. This should be recognized as one of the principal agents through which the great mineral potential of this Nation can be realized, and our international status as a mining power be assured without compromising the health and welfare of those who ensure it.The problem of more stringent dust standards will continue to grow. To date, approximately 40 pct of the coal mining industry has been placed on more stringent dust standards due to quartz. Control techniques must be improved if mandated levels are to be met. As longwall production increases, dust levels will also increase. In light of the industry trend toward longwall mining, if no new control technology is available, the Federal dust standard will act as a constraint on future output per hour. The Bureau has recently completed a survey of 18 coal preparation plants; 50 pct of these operate at dust levels which exceed 2.0 mg/m3; future work will be directed toward solutions in this area. The 2.0 mg standard for respirable dust is for dust particles which are below 10 pm in diameter. Recent studies have shown that dust in the range between 10 and 25 pm can cause obstructive airway disease. The Bureau is currently determining the extent of exposure to dust in this size range from various mining operations."

Nov 1, 1988

By P. G. Barnard

The Nation&apos;s steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

By Loyal Clarke, H. H. Storch

"The discovery of large deposits of polyhalite (K2S04.MgS04.2CaSO4.2H2O) in Texas has led to an investigation of possible industrial proecsses for the extraction of potash from this material. This mineral was first discovored in small quantities in the European potash deposits in or about the year 1800. Chemists fire thought it to be a form of calcium sulphate, but a more accurate analysis by Strohmiyer indicated the composition as given by the above formula.The decomposition of polytalite by aster is very slow and results in the formation of a layer of gypsum at the surface of the polyhalite which retarts the solution of the potaseium and magnesium sulphates. To obtain a substantial yield of K2S04 in solution it is necessary to use large amounts of water at room temperature, for he concentration of K2S04 is limited by the low solubility of syngonite (K2S04.CaS04.H2O) whereas at 100º C. several days boiling are necessary to obtain more than a 6 per cent K2S04 solution even when finely powdered polyhalite is employed.In 1854 H. Rose discovered that calcination, followed by leaching with water, resulted in a larger extraction of the potassium and magnesium sulphates, as compared with leaching without precalcination. During the course of a series of investigations concerning formation of oceanic salt deposits, Van't Hoff and his pupils obtained sufficient data to construct the equilibrium diagram for the system K+Mg+SO4--Ca++.H2O for 25° C. and for 83° C. These data are very well summarized. in the International Critical Tables' and by Boeke and Eitel. From a consideration of the diagrams for 83º C. one would conclude that an extraction of polyhalite with moderate amounts of water at 33º C. would result in a solution whose maximum concentration of K2So4 would be about 3.6 grams per 100 grams of water and of M2SO; about 4.0 grams per 100 grams of water, corresponding to equilibriumwith the solid phases: Polyhalite potassiam-calcium pentasulphate and anhydrite.The fact that it has been found possible to obtain as high as 11.4 grams of K2S04 per 100 grams of water (see table 6) and an equivalent amount of MgSo4 (8.1 grams per 100 grams of water was obtained corresponding to a ratio K2/Mg of 0.98; indicates that the formation of these complex salts is very slow. To be sure, this results was obtained at 100° C. instead of 83º C. However, the work of Anderson and Nestall 9 on the double salts of calcium and potassium sulphates at 100º C. indicates that the diagram at 100º C. C. would not be greatly different from that at 83º C. This slow rate of approach to equilibrium when combined with precalcination of,of polyhzli-,a is the 17,asis of some of the more p:olisinE methods of extracting potash from polyhalite."

Jun 1, 1930

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau&apos;s efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By Peter J. Clarke

Afghanistan&apos;s mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan&apos;s gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan&apos;s total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country&apos;s natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan&apos;s development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981

By Robert H. Lambeth

The Madison RARE II study area has four prospects with identified resources. These are listed in table 1 and are described in the following text. A high potential for Sillimanite exists at the Placer Creek occurrence (fig. 1, no. 7) and potential for phosphate rack in all areas underlain by the Phosphoria Formation. Some prospects exhibit minor potential for copper, lead, zinc, silver, and gold in the southern portion and very minor potential in the northern portion. Deposits in the northern end also have low potential for rare earth, asbestiform anthophyllite, or kyanite group minerals (including sillimanite).

Jan 1, 1982

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User&apos;s guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936