Search Documents

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By Eugene T. Sheridan

This circular presents data on individual plants of the fuel-briquet and packaged-fuel industries that responded to the Bureau of Mines annual economic survey and reported production for 1959. The companies named herein represent virtually all producers of processed fuels of mineral origin. A few small companies may not have been canvassed or failed to respond, however, as some plants operate intermittently, and the survey is voluntary. No consideration was given to size of the plant and all plants that reported commercial production were included. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, fabricated from fine-sized mineral fuels by mixing with binders and compressing into small individual shapes. Briquets usually are produced as small, pillow-shaped pieces, 2 to 4 inches long, weighing 2 to 4 ounces. Packaged fuel consists of 3- to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. The overall size of a popular package is 10-112 x 7 x 3-1/2 inches. Briquets are durable, may be stored outdoors, and shipped and used as bulk fuel. Packaged fuel is fragile, and must be stored indoors to keep it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times as a supplement to other fuels. Package fuel is burned without removing the paper and referred to as the "white-glove" fuel.

Jan 1, 1960

By Louis C. Brichta

This report summarizes the progress made by the Federal Bureau of Mines in assembling and compiling a catalog of available logs of drill holes and maps of mine developments in the Tri-State Zinc-Lead District in northeastern Oklahoma, southeastern Kansas, and southwestern Missouri. It supplements an interim report (11)3/ published in 1955, and for convenience of the reader repeats much of the general descriptive matter pertinent to the district contained in that report. The work of procuring and recording the data was begun in August 1949 and was recessed in May 1959. The catalog preserves the records of accomplished explorations and mine developments in the district and provides a readily available source of information for individuals and firms interested in planning mineral explorations, Government agencies estimating of reserves of mineral resources, and the mining industry for general use.

Jan 1, 1960

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By Charles L. Kimbell

Comprehensive data on market prices for crude minerals and mineral products for the world as a whole do not exist, and even the data that are available are not necessarily compatible between countries, particularly between the market economy countries and the centrally planned economy countries. Further, it should be evident that the actual delivered price for a small quantity of any specific commodity at some point substantially removed from a production facility or a seacoast port will differ appreciably from that for a large volume of the same product at or near its production source or a major import center. Nevertheless, the regularly published prices of selected major mineral commodities in key market areas can be regarded as indicative of general world price trends.

Jan 1, 1992

By Jack E. Fraley

The Bureau of Mines has successfully developed and tested a machine for spraying sealant onto coal mine roof and ribs. Dry material is transported pneumatically to a water-adding nozzle designed to provide dust-free spraying while being nonplugging and self-cleaning. The machine is self-cleaning, 35 inches in height, and capable of applying l/2-inch-thick coatings at over 1,000 ft2/hr.

Jan 1, 1978

By Charles L. Kimbell

In broadest overview, UN global industrial production indicators released and shown in table 2 suggest that the extractive sector of the world's mineral industry in aggregate registered a very slight upturn in 1991 relative to its 1990 performance. It also shows a continued rebound in the industry from the recessionary period of the mid-to late-1980's. These same indicators as calculated in late 1991, however, reflected a very minor downturn in extractive mineral industry operations between 1989 and 1990. This latter downturn represented a notable revision from the data reported in the immediate previous edition of this chapter, which suggested a tiny upturn. The apparent slight 1991 upturn in extractive sector industrial output generally was not mirrored in the performance of the processing sectors of the global mineral industry. Although the aggregate index for the chemicals, petroleum, coal, and rubber products manufacturers (see table 3) showed a notable gain in 1991, similar indices for nonmetallic mineral products and for base metals registered declines between 1990 and 1991. Examination of regional performance indices shows that the difficulties experienced in 1990 in maintaining output levels within the countries that formerly constituted the CMEA were reinforced by trends toward reduced gains in output levels, if not actual reductions in output, in several other areas. Generally speaking, the traditional developed market economy countries recorded downswings in overall industrial activity in 1991, particularly after midyear, whereas developing market economy countries logged gains. The developed market economy country downturns, however, were not nearly as significant as were the downturns recorded for the former centrally planned economy states - those that before 1992 were either constituent Republics within the U.S.S.R. or the latter's CMEA partners.

Jan 1, 1993

By Jon C. Volkwein

Advances in mining technology have enabled deeper seams of coal to be mined from the surface. Highwall mining is frequently used to mine areas at the perimeters of a surface mine when removal of the overburden becomes uneconomical or threatens environmentally sensitive surface features. At the same time, advances in materials and technology have enabled highwall mining of coal that create blind headings over 300 meters in length. Deeper surface mining and deeper highwall penetration depths have lead to more frequent encounters with methane gas. While this coal is remotely mined from the surface, underground ignitions of methane have propagated to the surface and injured miners. Methods described in this paper show how this hazard can be correctly monitored and controlled for auger type highwall mining machines. Research indicates that small quantities of gas liberated during mining migrate to the face, creating higher gas concentrations than would otherwise be expected. Using the same principles that cause the gas to migrate to the face, researchers have shown that inert gas introduced at the collar of the hole can inert the entire hole, thus ensuring safe conditions for mining.

By Donald P. Mickelsen

The raining and quarrying trends data shown in this report were reported to the U.S. Bureau of Mines (USBM) by mining and quarrying companies on the Mine Information Supplement survey, as well as by mineral producers on 58 annual USBM production and consumption surveys covering 59 nonfuel mineral commodities. The 1993 data presented in the tables of this chapter, were processed for the first time using the USBM Automated Mineral Information System. Domestic mining of nonfuel mineral materials totaled 3.7 billion metric tons in 1993, including 2.2 billion tons of crude ore nun& or quarried and 1.5 billion tons of mine waste and ore from development. This \vas an overall increase of 11% over that of 1992. These data do not include construction sand and gravel which until 1993 has been surveyed biennially. Starting in 1994, construction sand and gravel and the stones, which were also surveyed biennially, will be surveyed annually.

Jan 1, 1993

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

Develop a means for estimating vertical stress conditions in or around an underground mine so that appropriate measures for ground control can be taken before hazardous conditions arise. Background High vertical stress in an underground mine could cause or enhance hazardous ground control conditions which might lead to accidents, fatalities, and loss of reserves. An understanding of the vertical stress conditions at the mining level would allow a mine operator to take precautions that will minimize the occurrence of ground control problems. A knowledge of the underground stress conditions prior to mining could be used as an aid in future mine plan development to avoid or minimize ground control problems. Approach The Bureau of Mines developed a computer program for calculating the vertical stress resulting from the pressure of overlying rock masses on a mine or geologic surface at various depths.

Jan 1, 1990

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986